Mechanical Engineering Commons^™

Formula Sae Turbocharger Engine Development, Eric Griess, Kevin Mccutcheon, Matthew Roberts, William Chan

Mechanical Engineering

This project, Formula SAE Turbocharger System Development, was sponsored by the Cal Poly, San Luis Obispo Formula SAE team. The team proposed this project in order to have a powerful yet lightweight engine so they can be extremely competitive at their competition. The baseline output of the single cylinder 450cc engine (2006 Yamaha WR450F) was 46 horsepower and 27 ft-lb of torque. The goal of this project was to increase the output of that engine to 60 horsepower and 35 ft-lb through the use of a turbocharger.

Integrating Qplm And Biomedical Test Data With An Anisotropic Fiber Distribution Model And Predictions Of Tgf-Β1 And Igf-1 Regulation Of Articular Cartilage Fiber Modulus, Michael E. Stender, Christopher B. Raub, Kevin A. Yamauchi, Reza Shirazi, Pasquale Vena, Robert L. Sah, Scott J. Hazelwood, Stephen M. Klisch

Mechanical Engineering

A continuum mixture model with distinct collagen (COL) and glycosaminoglycan elastic constituents was developed for the solid matrix of immature bovine articular cartilage. A continuous COL fiber volume fraction distribution function and a true COL fiber elastic modulus ( Ef) were used. Quantitative polarized light microscopy (qPLM) methods were developed to account for the relatively high cell density of immature articular cartilage and used with a novel algorithm that constructs a 3D distribution function from 2D qPLM data. For specimens untreated and cultured in vitro, most model parameters were specified from qPLM analysis and biochemical assay results; consequently, Ef was …

Handitrike - Recumbent Tricycle, Sean Higginson, Kevin Howie, Vinay Patel

Mechanical Engineering

This report covers the design and construction of the recumbent racing tricycle for Mr. Robert T. Kelly, a disabled veteran. Unfortunately Rob’s right leg is five inches shorter than his left one and therefore is unable to properly operate standard cranks. Our team HandiTrike is composed of Sean Higginson, Kevin Howie, and Vinay Patel and our project requires us to come up with a design that is feasible to complete within the given three quarters, as well as allow Rob to gain full use of his tricycle. Currently Rob ‘s trike uses the standard crank set up found on most …

Micro-Grid Wind Energy System, Aaron Steinkraus, Brian Huntziker, Cesar Hurtado

Mechanical Engineering

With the completion of a 3.5kW wind turbine located on Esculea Ranch, the power generated from the turbine was dissipated through electric resistance heaters. ABC Wind was given the task to design, build, and implement a system what will efficiently use the turbine’s harnessed power. After interviewing with the Beef Operations Manager of Escuela Ranch, it was decided to use the turbine’s power to supply supplementary water to anywhere on the ranch where and when needed by grazing cattle. The purpose of this project was to research, design, build and implement a system that would harness the generated power and …

Solar Turbines Creep Test Fixture, Rene Maciel, Eric Nelson, Chris Ewald

Mechanical Engineering

No abstract provided.

Silicon Wafer Temperature Distribution, Daniel Gonzalez, Nathan Jones, Dylan Justice

Mechanical Engineering

Applied Materials is a global company that designs equipment for use in the semiconductor manufacturing industry. The scope of this project covers process chambers used for depositing thin chemical films onto silicon wafers. These processes must take place in particularly specific environments– including extremely low pressures and high temperatures. One challenge engineers face when designing these processes is carefully controlling the thermal behavior of silicon wafers. Typically, behavior is predicted using time consuming and computationally expensive CFD simulations. We have been asked to address this issue with a simpler, faster model which will allow engineers to reduce the total number …

Wolfpack Gear Inc. Composite Frame Firefighter Backpack, Gabriel Mountjoy, Blair Ridings, Carl Drummond Buchenroth

Mechanical Engineering

No abstract provided.

Hepa Filter Evaluation Furnace Control Unit, Matt Gainer, Marc Goupil, Andrew Woolrich

Mechanical Engineering

No abstract provided.

Cryogenic Heat Switch, Daniel Brodkey, Esteban Ruiz, Cristal Vasquez

Mechanical Engineering

A prototype cryogenic heat switch capable of transferring heat at cryogenic temperatures, while decoupling to prevent irreversible heat damage and minimizing parasitic heat loads, is to be developed for the Jet Propulsion Laboratory. Various material properties and cryogenic heat transfer processes will be investigated to determine the best solution for this project. A working proof of concept model will be constructed that may eventually be integrated onto a spacecraft’s passive cooler systems to protect them from the irradiation emitted by the sun, from the albedo of planets, and other malicious heat sources.

Polygrasp: Reach; Myoelectric Prosthetic Hand Iteration, Devon Patrick Augustus, Mighells Blaed Deuel, Ian Noel Fraser, Nicholas Philip Moesser

Mechanical Engineering

Amputations are a common occurrence in soldiers returning home who have suffered the effects of IED and munitions explosions. For upper limb amputees, trans-radial amputations are the most common. Traditional hook devices do not offer an adequate level of normalcy for users, prompting the use of myoelectric devices. While current myoelectric devices do offer a more natural experience, they come with a host of other problems that makes their adoption by service personnel not desirable or not permitted by the VA. PolyGrasp Reach seeks to reduce weight and cost and improve performance. This addresses several of the issues with devices …

Thermocouple Calibration Device, Angelica M. Larios, Cameron D. Peck, Andrew J. Smith

Mechanical Engineering

The goal of this project is to develop a thermocouple calibration unit with a high degree of confidence and accuracy. This thermocouple calibration device will be designed and developed at Cal Poly San Luis Obispo and delivered to Tesla Motors Inc.

To best utilize thermocouples, they must be calibrated to a known accuracy. Non-commercially produced thermocouples have unknown accuracies. The final deliverable will be a semi-automated device that produces a calibration curve for each thermocouple with a known confidence and accuracy.

Recreational Nordic Sit Ski, Mathew Bissonnette, Johnathon Gorski, Kevin Izumiya

Mechanical Engineering

The purpose of this project was to design, build, and test a recreational Nordic sit ski for use by Disabled Sports Eastern Sierra. The goal was to improve adjustability and reduce weight compared to previous sit ski designs. The project was completed by Cal Poly Mechanical Engineering seniors Mathew Bissonnette, Johnathon Gorski, and Kevin Izumiya. Kinesiology seniors Harpreet Saini and Carl Anderson provided discipline support and disability etiquette training.

The project was sponsored by the National Science Foundation Research to Aid Persons with Disabilities (RAPD) grant. The grant was proposed by and awarded to Dr. Brian Self and Dr. James …

Design Of A Releasable Snowboard Binding, Rex Crossen, Brian Kruse, Timothy Scott

Mechanical Engineering

A releasable snowboard binding will be proposed to our sponsor. This binding will allow the user to release and engage on demand for aerial tricks, comfort, and increased safety. The releasable snowboard binding we will come up with will be revolutionary within the snowboard industry and make current bindings old and inferior.

The Hovering Ball Exhibit, Matthew Bauzon, Will Lennox, Michelle Swan

Mechanical Engineering

No abstract provided.

Design Of An Independent Star-Clip Organizer (Iso), Christopher Gonzales, Greg Lovasik, Daniel Silveira

Mechanical Engineering

Discussed below is a new concept to sort and deliver star clips for flight deck safety net manufacturing. Multiple methods were generated, along with the necessary research, and were narrowed down to a single concept: the tray-loading preprocess design, named ISO (Independent Star-Clip Organizer). The overall design has been finalized and designed. Due to budget constraints, an actual prototype was not built. However, the design of such a prototype is described by this report, backed with calculations and experimental testing.

Innovative Cargo Rack Solutions, Travis Mccart, Brian Blummer, Whit Ratcliff

Mechanical Engineering

This report describes the process of designing, building, and testing a lowering mechanism for a roof-mounted SUV cargo box. It provides a detailed problem description and a specific list of requirements that our design must comply with. Existing products and concepts are presented which meet one or more of our design requirements. Six design concepts are discussed and down-selected to three for further development. A final design has been chosen and described in detail. A team management plan is included to specify member responsibilities and a schedule details major deadlines and goals. Manufacturing processes and testing procedures are described in …

Design Of A Human Powered Helicopter Airframe, Sheen Kao, Daniel Layton, Philip Sobol

Mechanical Engineering

In 1989 Cal Poly’s Da Vinci III was the first human powered helicopter (HPH) to achieve flight; our goal is to research and develop a new airframe for the next generation Da Vinci. This report outlines a brief history of human powered flight and details a method of constructing for the airframe. An optimized airframe geometry was also researched and is explained in detail.

Robotic Fingerspelling Hand For Deaf-Blind Communication, Brian Fang, Colby Dixon, Trevor Wong

Mechanical Engineering

Robotic fingerspelling hand for the deaf-blind. The hand forms the shapes of the American Manual Alphabet with 11 servos. The project was sponsored by The Smith-Kettlewell Eye Reaserch Institute.

Human Powered Helicopter: Rotor Structure, Joseph Ram, Juan Carlos Olvera

Mechanical Engineering

The following report encompasses the Human Powered Helicopter Rotor Team’s conceptual models and ideas based on research and modeling analysis. The following gives an overview of material researched, concept generation, analyzation, manufacturing, and testing for a rotor structure to be installed in a Human Powered Helicopter.

Senior Project #7: Longboard Test Apparatus, Derek Chan, Colin Harris, Nico Lee

Mechanical Engineering

The aim of this project is to create a machine that will test longboards made by Method Sports and Freebord. Through analysis and many iterations, Board Busters has assembled a design to fulfill the requirements set forth by these companies, who also sponsor the project. Through use of a four-bar, frame, and two spinning disks, the machine will accurately simulate riding conditions seen by a board in use by customers, allowing the sponsoring companies to improve designs and verify warranties.

Aerodynamic Test Platform For Human Powered Vehicle (Hpv), Spencer Wangerin, Spencer Lillywhite, Colburn Davis

Mechanical Engineering

The Aerodynamic Test Platform (ATP) for the Cal Poly HPV Club is a system that was designed by Cal Poly mechanical engineering students to measure aerodynamic characteristics of a human-powered vehicle (HPV). The HPV team desired a system that could quantify the lift, drag, and other aerodynamic qualities of a full scale HPV at various orientations in oncoming airflow. Established methods for determining aerodynamic characteristics include computational fluid dynamics (CFD) and wind tunnel testing of scaled models. The ATP was devised to simulate the test results given by a full-scale wind tunnel without requiring a wind tunnel large enough to …

Supermileage Chassis Dynamometer, Jose Garcia, Steve Janning, Timothy Lui, Kyla Purvis

Mechanical Engineering

This report describes the final design and analysis of a hydraulic chassis dynamometer as a testing tool for California Polytechnic State University, San Luis Obispo Supermileage Vehicle Team (CPSMV). Literature review was conducted to understand the various types of chassis dynamometers on the market as of the year 2011. After rigorous research, it was determined that a hydraulic system was the best system for a chassis dynamometer in terms of functionality, performance, and cost. Critical study of hydraulics, dynamometers, and data acquisition systems (DAQ) was followed by a complete design of a hydraulic system. The chassis dynamometer proposed in this …

California Olive Ranch Hedger, Tyler Enos, Seth Abbott, David Gamba

Mechanical Engineering

The purpose of this project is to evaluate the problems of the current KCI (Kingsburg Cultivator Incorporated) olive tree hedger in use at California Olive Ranch (COR) in Artois, CA, and then correct these problems which should yield a better performing, more efficient, and reliable machine. These problems include: the hydraulic oil temperature getting too high, the saw blades not having enough horsepower, and poor cutting performance due to operator error as well as terrain variations.

Main Reduction Gear Debris Identification And Removal Device, Gordon Cline, Alex Tittiger, Michael O'Brien

Mechanical Engineering

This report details the development of a tool to remove objects and debris from a large gearbox found on ships of the United States Navy, specifically to be used by NAVSEA. The tool is to be used in situations where an object or contaminant cannot easily be removed or found without completely disassembling the gearbox. This will be done using a boom arm, a cable, a gripper and a borescope. This combination will allow for a large amount of mobility and versatility when searching for the object or contaminant, which is necessary for use in different gearboxes. The process we …

Design And Testing Of A Low Cost Prosthetic Foot, Shalan Ertis, John Kearns, Seija Maniskas

Mechanical Engineering

No abstract provided.

Throwing Frame For Athletes With Dissabilities, Andrew Higgins, Stefan Owechko, Gabriel (Gabe) Terrasas, Kevin Crisfield

Mechanical Engineering

Team Zeus’ senior project was to design, build and test a working throwing frame system for Bridge II Sports, a nonprofit organization in North Carolina. The throwing frame is used to allow athletes and individuals with disabilities to throw shot-put, discus, and javelin using a frame to sit against. Team Zeus was specifically tasked to build a frame that is lighter weight and more transportable than products that are currently on the market. This frame also is adjustable to accommodate a wide range of athlete weights, sizes, and abilities. The final result is a 35lb aluminum frame with two different …

Mini Pump, Stephen Scruggs, Britta Berg-Johansen, Kyle Kriete

Mechanical Engineering

No abstract provided.

Formula Hybrid Drivetrain Design, Zachary (Zak) Mcfarland, Alex Pruitt, William Domhart

Mechanical Engineering

The Formula Hybrid senior project group was tasked with designing and building a drivetrain system for the Cal Poly Society of Automotive Engineers (SAE) Formula Hybrid (FHSAE) team. FHSAE gave customer requirements for performance and geometry for the drivetrain and the FHSAE rulebook has guidelines regarding safety requirements. The team chose to compete in the electric category of the 2012 FHSAE competition. After getting feedback from previous car performance and researching different powertrain options, the senior project team arrived at three conceptual ideas. Using a quality function deployment method, the senior project team chose the concept where two motors independently …

Polycart, Ryan Bolton, Vincent Contreras, Rodrigo Sanchez

Mechanical Engineering

No abstract provided.

Sole Power: Pedal Phone Charger Final Report, Nicole Hensley, Anthony Ruh, Krista Schmidt, Joseph Garcia

Mechanical Engineering

The device design was conceived to meet the energy needs of rural populations in India. These communities have cell phones but lack access to reliable grid power, especially during monsoon season. The charger is designed to be affordable, durable, and easily repairable for each owner family. It uses off-the-shelf components and is intended to be replicated by backyard manufacturing startups in developing countries.

Its purpose is to efficiently transfer human foot motion via a treadle, four-bar-linkage, and sprocket-chain step-up to drive a rotor & stator generator from a common gas scooter. The single-phase alternating current from the generator is passed …