Mechanical Engineering Commons^™

Investigation Of The Quenching Characteristics Of Steel Components By Static And Dynamic Analyses, Pratik Sarker

University of New Orleans Theses and Dissertations

Machine components made of steel are subjected to heat treatment processes for improving mechanical properties in order to enhance product life and is usually done by quenching. During quenching, heat is transferred rapidly from the hot metal component to the quenchant and that rapid temperature drop induces phase transformation in the metal component. As a result, quenching generates some residual stresses and deformations in the material. Therefore, to estimate the temperature distribution, residual stress, and deformation computationally; three-dimensional finite element models are developed for two different steel components – a spur gear and a circular tube by a static and …

Modal Characterization And Structural Dynamic Response Of A Crane Fly Forewing, Jose E. Rubio

University of New Orleans Theses and Dissertations

This study describes a method for conducting the structural dynamic analysis of a crane fly (family Tipulidae) forewing under different airflow conditions. Wing geometry is captured via micro-computed tomography scanning. A finite element model of the forewing is developed from the reconstructed model of the scan. The finite element model is validated by comparing the natural frequencies of an elliptical membrane with similar dimensions of the crane fly forewing to its analytical solution. Furthermore, a simulation of the fluid-structure interaction of the forewing under different airflows is performed by coupling the finite element model of the wing with a …

Utilizing Failure Information For Mission Assessment And Optimization For Complex Systems, Charlie Destefano

Graduate Theses and Dissertations

This paper presents a new failure analysis method, Failure Identification for Mission Analysis (FIMA), which performs a general failure analysis for the overall state of a system, as well as a mission-specific analysis that identifies how failures may have differing effects on the various mission tasks that a system must complete. The FIMA method is capable of being implemented at any point in the design process. During early design stages, the FIMA method will identify various qualitative failure scenarios based on programmed functional relationships and any number of initial failures wished to be simulated. The functional relationships for this method …

Highly Transparent, Self-Cleaning, And Antireflective Nanoparticle Coatings, Corey Seth Thompson

Graduate Theses and Dissertations

Current solar panel technologies require a sheet of glass to serve as both mechanical support and to protect the cells from the environment. The reflection from the glass sheet can reflect up to 8% of the incident light, reducing the power output of the panel. Antireflective coatings can be used to allow more light to enter the panel to be converted into usable electricity. However, no solid thin film materials exhibit a low enough index of refraction to serve as antireflective coatings for common solar glass. The main goal of this research was to investigate the self-cleaning, antifogging, and antireflective …

Cold Roll Extrusion Machine Redesign Final Design Report, Foja Bains, Bryan Cyr, David Van Schooten

Mechanical Engineering

This report is a comprehensive review of a redesign of subsystems for a Cold Roll Extrusion Machine, a forging operation, for PCC Rollmet. Three subsystems were addressed in this project: A new Loading system, Feed system, and Lubrication system. The Loading system, and support system during developmental design stages, addressed the timely loading process of pipes onto the forging machine. After two quarters of design iteration, the group decided on a lever arm, hydraulic actuated, loading design. In the final quarter of the project, a quarter scale model of this lever arm was constructed to prove the concept of the …

Team Nathan Suspension, Frankie J. Wiggins, Alex D. Seitz, Justin P. Bautista

Mechanical Engineering

Nathan Cooper is an 8-year old boy with Spinal Muscular Atrophy (SMA). SMA has affected Nathan’s muscle development and requires him to use the Standing Dani™ mobility device. The Standing Dani is a motorized standing wheelchair, or Wheelstand. Nathan controls and uses it to get around. Though the Standing Dani performs well for most functions, it has some distinct issues. The primary issue that this project addresses is its lack of suspension and the discomfort that Nathan feels as a result. After talking with our client, we developed several specifications generally related to geometry, safety, vehicle dynamics, and reliability. Many …

Simulations Of Diffusion Driven Phase Evolution In Heterogenous Solids, Subramanya Gautam Sadasiva

Open Access Dissertations

With reduction in size, ever greater operational demands are placed on electronics components at all levels of the device, starting from the transistor level to the level of the package and the solder interconnects. Concurrently, there has been a move to more complicated materials systems in order to meet health and environmental guidelines. These trends of reducing size, increasing loads have increased the necessity to understand the mechanisms of the failure. ^ As the length scales are reduced, it becomes increasingly important to consider interfacial and micro-structural effects that can be safely ignored at larger length scales owing to the …

Structural Response Analyses Of Piezoelectric Composites Using Nurbs, Vijairaj Raj

Electronic Thesis and Dissertation Repository

Variational method deduced on the basis of the minimum potential energy is an efficient method to find solutions for complex engineering problems. In structural mechanics, the potential energy comprises strain energy, kinetic energy and the work done by external actions. To obtain these, the displacement are required as a priori. This research is concerned with the development of a numerical method based on variational principles to analyze piezoelectric composite plates and solids. A Non-Uniform Rational B-Spline (NURBS) function is used for describing both the geometry and electromechanical displacement fields. Two dimensional plate models are formulated according to the first order …

Creasing Instability Of Hydrogels And Elastomers, Dayong Chen

Doctoral Dissertations

CREASING INSTABILITY OF HYDROGELS AND ELASTOMERS MAY 2014 DAYONG CHEN, B.S., TIANJIN UNIVERISTY M.S., TIANJIN UNIVERSITY M.S., UNIVERSITY OF MASSACHUSETTS AMHERST Ph.D., UNIVERSITY OF MASSACHUSETTS AMHERST Directed by: Professor Ryan C. Hayward Soft polymers placed under compressive stress can undergo an elastic creasing instability in which sharp folds spontaneously form on the free surfaces. This process may play an important role in contexts as diverse as brain morphogenesis, failure of tires, and electrical breakdown of soft polymer actuators. While the creasing instability has been used for collotype printing since as early as the 1850s, the scientific appreciation of this instability …

Atomistic Simulation And Virtual Diffraction Characterization Of Alumina Interfaces: Evaluating Structure And Stability For Predictive Physical Vapor Deposition Models, Shawn Patrick Coleman

Graduate Theses and Dissertations

The objectives of this work are to investigate the structure and energetic stability of different alumina (Al₂O₃) phases using atomistic simulation and virtual diffraction characterization. To meet these objectives, this research performs molecular statics and molecular dynamics simulations employing the reactive force-field (ReaxFF) potential to model bulk, interface, and surface structures in the θ-, γ-, κ-, and α-Al₂O₃ system. Simulations throughout this study are characterized using a new virtual diffraction algorithm, developed and implemented for this work, that creates both selected area electron diffraction (SAED) and x-ray diffraction (XRD) line profiles without assuming …

Electroencephalography(Eeg) Data Collection And Processing Through Machine Learning, Jayshree Desai

Graduate Theses and Dissertations

Machine learning methods are an excellent way for understanding the neural basis of human decision making. Some machine learning systems try to eradicate the need for human intuition in data analysis whereas others embrace a collective approach between humans and machines. The objective of this project is to collect Electroencephalography (EEG) signals through wireless sensors, and the process the collected signals through machine learning methods. The EEG data is collected using three EEG electrodes, each being the positive, negative and ground terminals respectively. Since the signal measures in the unit of micro-volts it needs to be amplified using amplifier circuit. …

Influence Of Approach Flow Conditions On Urban Street Canyon Flow, Karin Blackman

Electronic Thesis and Dissertation Repository

The turbulent flow within a street canyon and the approaching boundary layer has been studied using idealized wind tunnel models and a semi-idealized field experiment conducted in Nantes, France. The effect of upstream roughness on street canyon flow (lateral length/height, L/h = 30) using either 3D (cube) or 2D (rectangular block) upstream roughness, of the same height as the canyon, has been studied for two streamwise canyon width to height aspect ratios (AR) of 1 and 3 using Particle Image Velocimetry. A further wind tunnel model of equivalent geometry to the field experiment was used to compare with flow data …

An Experimental Fatigue And Finite Element Study Of A Welded Joint Of A Snowplow Blade, George Ernest Selburg

Master's Theses (2009 -)

This study describes a method to evaluate the fatigue life of a welded joint of a snowplow. Fatigue specimens were then fabricated, which simulated the joint and its loading characteristics. The joint in the specimens were characterized by measuring the geometry of the weld and the hardness of the parent material, weld material, and heat affected zone. It was determined that the fatigue crack that developed in the joint was exposed to mode I fracture forces in the normal plane of the crack. The specimens were then tested in a hydraulic closed looped system to determine the mechanism of fatigue …

Transverse Compression Of High-Performance Ballistic Fibers, Zherui Guo

Open Access Theses

High performance ballistic fibers have been in use for decades, specifically in protective applications against ballistic impact such as bulletproof vest layers and aircraft turbine engine fragmentation barriers. These high performance fibers have extremely high strength-to-weight ratios and high moduli of elasticity in the axial direction, making them extremely suitable for high impact situations. In particular, para-phenyleneterephthalamide (PPTA for short) fibers such as Kevlar^® and ultra-high-molecular-weight polyethylene fibers such as Dyneema^® are amongst the more popular high performance fibers in today's world. While the longitudinal mechanical response of these fibers have been extensively researched, their transverse mechanical response …

Meshless Mechanics And Point-Based Visualization Methods For Surgical Simulations, Rifat Aras

Computational Modeling & Simulation Engineering Theses & Dissertations

Computer-based modeling and simulation practices have become an integral part of the medical education field. For surgical simulation applications, realistic constitutive modeling of soft tissue is considered to be one of the most challenging aspects of the problem, because biomechanical soft-tissue models need to reflect the correct elastic response, have to be efficient in order to run at interactive simulation rates, and be able to support operations such as cuts and sutures.

Mesh-based solutions, where the connections between the individual degrees of freedom (DoF) are defined explicitly, have been the traditional choice to approach these problems. However, when the problem …

Mechanistic Failure Criterion For Unidirectional And Random Fibre Polymer Composites, Jamaloddin Jamali

Electronic Thesis and Dissertation Repository

Polymer composite design in energy absorbing components requires a failure criterion that can predict the energy involved in its fracture under different modes of loading. Present mixed mode criteria are mainly empirical or semi-empirical, and are only suitable for a small range of composite types.

The purpose of this study was to develop a mechanistic failure criterion that is applicable to a wide range of polymer composites. An energy based mechanistic failure criterion is proposed to characterize the toughness of unidirectional (UD) and randomly oriented short fibre composites (random fibre composites).

In UD and random composites, the criterion predicts the …

Cnc Torch, Steven Chiu

Computer Engineering

This CNC Torch cuts steel plate. It can cut up to a maximum area of 3x3 feet. The user builds a cut list on the touchscreen from a selection of predefined shapes and enters the parameters need for each shape. When the user is ready, the cut list is sent to an Arduino that will move each motors accordingly to the shapes desired.

Modification Of A Draw Bar Type Arena Harrow To Three Point Mounted Type Harrow, Clayton Alan Brown

BioResource and Agricultural Engineering

This senior project will be the design, and construction of a three point hitch to be attached to a draw bar type spike tooth harrow. Currently used by the Cal Poly Rodeo Team to cultivate their arena before performances, and practices.

The attachment will allow the harrow to be pulled in both directions to create different types of soil affects.

Also the fabrications has a minimal budget so the majority of the materials will be scrap material already in position of the rodeo team or donated to the project.

Formula Sae Hybrid Carbon Fiber Monocoque / Steel Tube Frame Chassis, Matthew Hagan, John Rappolt, John Waldrop

Mechanical Engineering

The Cal Poly Formula SAE Team created this project in order to design and fabricate a high-performance chassis which would be competitive at 2013 FSAE Lincoln, and to document the process so that future teams could more easily create a chassis. One of the main goals was to reduce weight from the 143- lb 2012 chassis subsystem. A weight of 95 lb was achieved, with 82 lb in the chassis structure itself and a predicted torsional stiffness of 1700 lb*ft/deg. Composite materials design and manufacturing techniques were developed during the project. Design, testing, and manufacturing processes are detailed, and results …

Folding Wheelchair Improvement, Matthew Edison Grace, Kevin Alan Miyamoto, Andrey Lee Oliveira

Mechanical Engineering

No abstract provided.

Automated Foosball Table, Jim R. Stefani, Alex J. Herpy, Brett Gordon Jaeger, Kevin S. Haydon, Derek Alan Hamel

Mechanical Engineering

This project is the second iteration of an automated foosball table for Yaskawa America as a trade show display. The table is meant to provide an interactive experience which highlights the speed and precision of the Yaskawa hardware. The first iteration of the project was mainly focused on creating the physical hardware for the system and to begin the basic programming for the system. This phase of the project was focused on finalizing the physical hardware of the system, implementing the vision system and to continue the basic programing of the system AI. A third team will be assigned to …

Adaptive Basketball Shooter - Final Project Report, Jenna N. Becker, Richard A. Galanti, Justin D. Haley, Brett Y. Nayudu

Mechanical Engineering

The Friday Club is a joint venture between the Cal Poly Kinesiology Department and the San Luis Obispo Special Olympics that offers people with varying degrees of disability the opportunity to meet weekly and learn various sports and games. At Friday Club, athletes in wheelchairs with limited arm strength use devices built by Cal Poly mechanical engineering students in order to participate in various sports. Many devices are designed to attach to the Universal Play Frame (UPF), a wheel-chair attachment. The purpose of this project was to design and build a UPF device that will launch a basketball, so that …

Friction Test Machine, Kyle Raymon Schless, Lynda Beatriz Tesillo, Mustapha Nadri

Mechanical Engineering

No abstract provided.

Lightweight Uav Launcher, Ben Miller, Christian Valoria, Corinne Warnock, Jake Coutlee

Mechanical Engineering

This report discusses the design, construction, and testing of a lightweight, portable UAV launcher. There is a current need for a small team of soldiers to launch a US Marine Tier II UAV in a remote location without transport. Research was conducted into existing UAV launcher designs and the pros and cons of each were recorded. This research served as a basis for concept generation during the initial design development stage. It was required that the design weigh less than 110 lbs, occupy a smaller volume than 48" x 24" 18" in its collapsed state, be portable by a single …

Strain-Based Design Methodology Of Large Diameter Grade X80 Linepipe, Mark D. Lower

Doctoral Dissertations

Continuous growth in energy demand is driving oil and natural gas production to areas that are often located far from major markets where the terrain is prone to earthquakes, landslides, and other types of ground motion. Transmission pipelines that cross this type of terrain can experience large longitudinal strains and plastic circumferential elongation as the pipeline experiences alignment changes resulting from differential ground movement. Such displacements can potentially impact pipeline safety by adversely affecting structural capacity and leak tight integrity of the linepipe steel.

Planning for new long-distance transmission pipelines usually involves consideration of higher strength linepipe steels because their …

Thermal Hydraulic Characteristics Of Fuel Defects In Plate Type Nuclear Research Reactors, Isaac Thomas Bodey

Doctoral Dissertations

Turbulent flow coupled with heat transfer is investigated for a High Flux Isotope Reactor (HFIR) fuel plate. The Reynolds Averaged Navier-Stokes Models are used for fluid dynamics and the transfer of heat from a thermal nuclear fuel plate using the Multi-physics code COMSOL. Simulation outcomes are compared with experimental data from the Advanced Neutron Source Reactor Thermal Hydraulic Test Loop. The computational results for the High Flux Isotope Reactor core system provide a more physically accurate simulation of this system by modeling the turbulent flow field in conjunction with the diffusion of thermal energy within the solid and fluid phases …

Investigation Of Boiling Performance Of Graphene-Coated Surfaces, Daniel C. Stack

Honors Capstone Projects - All

In this Capstone Project, I sought to investigate the boiling performance of graphene-coated surfaces. Boiling was accomplished in a pool boiling chamber, with samples of graphene-coating SiO₂ wafers. I developed a procedure for graphene transfer for sample fabrication. Samples were prepared with graphene grown on copper substrates by chemical vapor deposition (CVD). Graphene was transferred from copper substrates to SiO­₂ wafers by a thermal release transfer tape. Copper was etched away from the tape-graphene combination by ferric chloride, and the tape was peeled away after heating, leaving graphene on the SiO₂ substrate. Contact angles were measured to …

Rotordynamic Analysis Of A Two-Pole Synchronous Motor With Sleeve And Pressure Dam Bearings, Justin Matthew Garrard

Masters Theses

A two-pole synchronous motor was recently rewound for the von Karman Gas Dynamics facility at Arnold Engineering Development Complex, Arnold Air Force Base, Tennessee. After installing the rewound rotor, unexpected vibration amplitudes were recorded during motor checkouts. To resolve this issue, an investigation was initiated to investigate the causes of the vibration issues. The investigation discovered that the original design used sleeve bearings rather than pressure dam bearings. A study was formed to determine the effect of changing the pressure dam bearings back to sleeve bearings. Because only one spare bearing shell existed, the bearing with the highest vibration amplitudes …

Study Of Aluminum Honeycomb Sandwich Composite Structure For Increased Specific Damping, Aditi S. Joshi

Open Access Theses

The aluminum honeycomb sandwich composite structure is commonly used in the aerospace and automotive applications where high strength to weight ratio is desirable. However the poor performance of the aluminum honeycomb sandwich composite structure in terms of the vibration damping and the sound transmission makes their applications limited. Studying the effect of different structural modifications on the damping has become an interesting area of research in past few decades. The present study addresses the effect of adding a mass on the composite beam at various locations on the damping loss factors for the modes of vibration present in the frequency …

An Assessment Of Flow Regime Maps And A Numerical Heat Transfer Correlation For The Stratified/Annular Regime Of Shear-Driven Internal Condensing Flows, Fnu Nikhil Shankar

Dissertations, Master's Theses and Master's Reports - Open

Several modern-day cooling applications require the incorporation of mini/micro-channel shear-driven flow condensers. There are several design challenges that need to be overcome in order to meet those requirements.

The difficulty in developing effective design tools for shear-driven flow condensers is exacerbated due to the lack of a bridge between the physics-based modelling of condensing flows and the current, popular approach based on semi-empirical heat transfer correlations. One of the primary contributors of this disconnect is a lack of understanding caused by the fact that typical heat transfer correlations eliminate the dependence of the heat transfer coefficient on the method of …