Mechanical Engineering Commons^™

Experimental And Numerical Characterization Of Multiphase Subsurface Oil Release, Feng Gao

Dissertations

Subsurface oil release is commonly encountered in the natural environment and engineering applications and has received the substantial attention of researchers after the disastrous Deepwater Horizon Blowout oil spill in 2009. The main focus on the present research is to systematically study the hydrodynamics of underwater oil jet under a variety of conditions, including the effect of dispersant and different gas to oil ratios (GOR) by using experimental measurement as well as a Computational Fluid Dynamics (CFD) approach, from which the measured turbulent characteristics (e.g., velocity, turbulent kinetic energy, turbulence dissipation rate, etc.) of underwater oil jet are thoroughly examined …

Elevated Temperature Progressive Damage And Failure Of Duplex Stainless Steel, Darren P. Luke

Civil Engineering ETDs

Ductile failure of metals has been the focus of research efforts within academia and industry for many years since it is tremendously important for understanding the failure of structures under extreme loading conditions. However, limited research has been dedicated to elevated temperature ductile failure, which is critical for evaluating catastrophic events such as industrial, structural or shipping vessel fires. A detailed investigation was conducted on the structural response of Duplex Stainless Steel at elevated temperatures. The temperature dependence of elastic modulus, yield strength, ultimate strength, and ductility was measured up to 1000°C and a continuum damage plasticity model was developed. …

Towards Environmentally Sustainable And Cost-Effective Food Distribution In The U.S., Jasmina Burek

Graduate Theses and Dissertations

Distribution centers (DCs) and supermarkets have an important role in food sustainability, but no previous research has accounted for their environmental impact. The purpose of this research was to assess environmental sustainability of grocery, perishables, and general merchandise DCs; to estimate food storing and retailing impact; and to provide cost-effective strategies to reduce DCs’ environmental impacts. The importance and relevance of the research is threefold: improving sustainability of DCs, food storing, and food retailing. The main method used in this research was the life cycle assessment (LCA) method. An initial study calculated environmental impacts of the Wal-Mart Stores, Inc. DCs, …

Transient Analysis Of Full Scale And Experimental Downburst Flows, Junayed Chowdhury

Electronic Thesis and Dissertation Repository

Downbursts are highly transient natural phenomena which produce strong downdrafts evolving from a cumulonimbus cloud They induce an outburst of damaging winds on or near to the ground causing an immense damage to the ground mounted structures and aircrafts. This study investigates the transient nature of downbursts using wind speed records from full scale downburst events employing an objective methodology. This method can detect the abrupt change points in a downburst time series based on statistical parameters such as mean, standard deviation and linear trend. In addition to the analysis of the full scale downburst events, several large scale experimental …

Selecting The Most Effective Energy Modeling Tool Based On A Project Requirement, Sodiq Akande

Electronic Theses and Dissertations

Building energy usage can be derived and controlled by performing building energy modeling. BEM can be performed using numerous software tools such as DesignBuilder, OpenStudio, EnergyPlus etc. These modeling tools can be sorted into three different modeling categories: Black-box, Gray-box and White-box. It is important for a modeler to be able to quickly select the proper tool from the proper category to meet the need of the project. To validate the method of categorizing tools, the three models generated using tools from each category and the modeling outputs required were compared. Each model was designed to estimate the amount of …

Microstructural Characterization Of Shear Transformation Zones And Modeling Indentation Size Effect In Amorphous Polymers, Leila Malekmotiei

LSU Doctoral Dissertations

The first aim of this work is developing a procedure for experimental and analytical characterization of nano-scale microstructures which mediate large scale deformation in amorphous polymers. Glassy polymers are extensively used as high impact resistant, low density, and clear materials in industries. Nevertheless, their response under severe loading conditions is yet to be appropriately unraveled. Due to the lack of long-range order in the microstructures of glassy solids, their plastic deformation is different from that in crystalline solids. Shear Transformation Zones (STZs) are believed to be the main plasticity carriers in amorphous solids and defined as the localized atomic or …

Efficient Adjacency Queries And Dynamic Refinement For Meshfree Methods With Applications To Explicit Fracture Modeling, James Olliff

USF Tampa Graduate Theses and Dissertations

Meshfree methods provide a more practical approach to solving problems involving large deformation and modeling fracture compared to the Finite Element Method (FEM). However meshfree methods are more computationally intensive compared to FEM, which can limit their practicality in engineering. Meshfree methods also lack a clear boundary definition, restricting available visualization techniques. Determining particle locations and attributes such that a consistent approximation is ensured can be challenging in meshfree methods, especially when employing h-refinement. The primary objective of this work is to address the limitations associated with computational efficiency, meshfree domain discretization, and h-refinement, including both placement of particles as …

Fundamentals Of Applied Smouldering Combustion, Marco Zanoni

Electronic Thesis and Dissertation Repository

Smouldering combustion is defined as a flameless oxidation reaction occurring on the surface of the condensed phase (i.e., solid or liquid). Traditional research on smouldering was related to economic damages, fire risk, and death, due to the release of toxic gases and slow propagation rates. Recently, smouldering has been applied as an intentional, engineering technology (e.g., waste and contaminant destruction). Smouldering involves the transport of heat, mass, and momentum in the solid and fluid phases along with different chemical reactions. Therefore, numerical models are essential for the fundamental understanding of the process. Smouldering models either neglected heat transfer between phases …

Experimental, Analytical, And Numerical Evaluation Of The Mechanical Properties Of The Brain Tissue, Aref Samadidooki

LSU Doctoral Dissertations

A true understanding of the mechanisms behind most of the brain diseases is still out of reach. For several years, the interest of scientists has been focused on the genetic and biological causes, however, recent studies unraveled the importance of the biomechanics of the brain growth, folding, impact resistance, and deformation on its pathological conditions. While, a wide range of different methods have been used for characterization of the mechanical properties of the brain at the tissue level, the obtained results from different studies are extremely scattered and sometimes in contrast to one another. Since the brain tissue is extremely …

Diesel Particulate Generation, Matthew Ferdenzi

Honors Theses

The goal of this project is to design a diesel particulate generator to test aerogels as diesel particulate filters. Diesel particulate generators are machines that generate diesel particulate matter, or diesel soot. Diesel particulate filters have been recently put into the market to help many car companies meet the ever-changing diesel emission regulations set by the EPA and other international agencies. The main goal of the filter is to block soot from exiting to the environment. Once the filter is full, the soot is oxidized and released. The problem with these filters is that they are large, costly, detrimental to …

Preliminary Investigation Of Tensile Strength And Impact Characterization Of Cementitious Composite Incorporating Carbon Nanotubes, Robabeh Jazaei

UNLV Theses, Dissertations, Professional Papers, and Capstones

Cement has been largely used in the construction industry, specifically as a matrix for concrete. Recently, a new generation of cement-based composite that greatly increases mechanical properties is replacing conventional concrete. With periodic advances in the field, researchers considered particles with high-aspect ratios such as Carbon Nanotubes (CNTs) to reinforce cement matrices. Although there is not much literature to draw upon in research, some research on improving the tensile strength of cementitious composite incorporating with CNTs does exist. However, there had been no evidence of investigation into impact strength until this study.

Most papers presented examined the effect of multi-walled …

Effects Of Tension On Resonant Frequencies Of Strings, Blake Burnett

Senior Theses

This project tests and explores resonance of strings. Since all materials and mechanisms are affected by vibrations, it is important to know the frequencies at which resonance occurs. To explore this subject, strings were used as a model material to test the effect tension has on resonance. The fundamental frequencies and the corresponding modes of resonance were used to analyze the data. The results of this experiment show that increasing tension on a string increases its resonance frequency. Understanding the physics behind resonance frequency allows systems to be designed to take advantage of resonance properties, or to avoid resonance where …

Simplified, Alternative Formulation Of Numerical Simulation Of Proton Exchange Membrane Fuel Cell, Russell L. Edwards

Mechanical & Aerospace Engineering Theses & Dissertations

Three-Dimensional proton exchange fuel cell (PEMFC) operation in steady-state is simulated with computational fluid dynamics / multiphysics software that is based upon the finite-element method. PEMFC operation involves the simultaneous simulation of multiple, interconnected physics involving fluid flows, heat transport, electrochemical reactions, and both protonic and electronic conduction. Modeling efforts have varied by how they treat the physics occurring within and adjacent to the membrane-electrode assembly (MEA). Several approaches treat the MEA as part of the computational domain, solving multiple, and coupled conservation equations via the CFD approach within the 3 regions of the MEA. The thickness dimensions of the …

Modeling Deformation Behavior And Strength Characteristics Of Sand-Silt Mixtures: A Micromechanical Approach, Mehrashk Meidani

Doctoral Dissertations

This dissertation is comprised of six chapters. In the first chapter the motivation of this research, which was modeling the deformation behavior and strength characteristics of soils under internal erosion, is briefly explained. In the second chapter a micromechanis-based stress-strain model developed for prediction of sand-silt mixtures behavior is presented. The components of the micromechanics-based model are described and undrained behavior of six different types of sand-silt mixtures is predicted for several samples with different fines contents. The need for a more comprehensive compression model for sand-silt mixtures is identified at the end of this chapter. This desired compression model …

Quantitative Phase-Field Modeling Of Crack Propagation In Multi-Phase Materials, Arezoo Emdadi

Doctoral Dissertations

”Research presented in this dissertation is focused on developing and validating a computational framework for study of crack propagation in polycrystalline composite ceramics capable of designing micro-architectures of phases to improve fracture toughness and damage tolerance of ZrB₂-based ultra-high temperature ceramics (UHTCs). A quantitative phase-field model based on the regularized formulation of Griffith’s theory is presented for crack propagation in homogenous and heterogeneous brittle materials. This model utilizes correction parameters in the total free energy functional and mechanical equilibrium equation within the crack diffusive area to ensure that the maximum stress in front of the crack tip is …

Dust Control Examination Using Computational Fluid Dynamics Modeling And Laboratory Testing Of Vortecone And Impingement Screen Filters, Ashish R. Kumar

Theses and Dissertations--Mining Engineering

Heavy industries, such as mining, generate dust in quantities that present an occupational health hazard. Prolonged exposure to the respirable dust has been found to result in many irreversible occupational ailments in thousands of miners. In underground mining applications, a variety of scrubbing systems are used to remove dust near the zones of generation. However, the wire-mesh type fibrous screens in the flooded-bed dust scrubbers used on continuous miners, are prone to clogging due to the accumulation of dust particles. This clogging results in a reduced capture efficiency and a higher exposure to the personnel. This research establishes the Vortecone, …

Optimal Sintering Temperature Of Ceria-Doped Scandia Stabilized Zirconia For Use In Solid Oxide Fuel Cells, Amanda K. Assuncao

Honors Undergraduate Theses

Carbon emissions are known to cause decay of the Ozone layer in addition to creating pollutant, poisonous air. This has become a growing concern among scientists and engineers across the globe; if this issue is not addressed, it is likely that the Earth will suffer catastrophic consequences. One of the main culprits of these harmful carbon emissions is fuel combustion. Between vehicles, power plants, airplanes, and ships, the world consumes an extraordinary amount of oil and fuel which all contributes to the emissions problem. Therefore, it is crucial to develop alternative energy sources that minimize the impact on the environment. …

An Integrated Closed Convergent System For Optimal Extraction Of Head-Driven Tidal Energy, Michelle Ann Vieira

UNF Graduate Theses and Dissertations

As the demands for energy increased with the global increase in population, there is a need to create and invest in more clean and renewable energy sources. Energy derived from the movement of the tides is an ancient concept that is currently being harnessed in a handful of large tidal range locations. However, the need to move from fossil fuel driven energy sources to those that are clean and non-polluting is a priority for a sustainable future. Globally, hydropower potential is estimated to be more than 16,400-Terawatt hours annually. Given that the electricity consumption worldwide was at 15,068-Terawatt hours in …

Numerical Modeling Of Capillary-Driven Flow In Open Microchannels: An Implication Of Optimized Wicking Fabric Design, Mehrad Gholizadeh Ansari

Masters Theses

"The use of microfluidics to transfer fluids without applying any exterior energy source is a promising technology in different fields of science and engineering due to their compactness, simplicity and cost-effective design. In geotechnical engineering, to increase the soil's strength, hydrophilic wicking fibers as type of microfluidics have been employed to transport and drain water out of soil spontaneously by taking advantage of natural capillary force without using any pumps or other auxiliary devices. The objective of this study is to understand the scientific mechanisms of the capability for wicking fiber to drain both gravity and capillary water out of …

Pressure-Driven Stabilization Of Capacitive Deionization, Landon S. Caudill

Theses and Dissertations--Mechanical Engineering

The effects of system pressure on the performance stability of flow-through capacitive deionization (CDI) cells was investigated. Initial data showed that the highly porous carbon electrodes possessed air/oxygen in the micropores, and the increased system pressure boosts the gases solubility in saline solution and carries them out of the cell in the effluent. Upon applying a potential difference to the electrodes, capacitive-based ion adsorption occurs in competition with faradaic reactions that consume oxygen. Through the addition of backpressure, the rate of degradation decreases, allowing the cell to maintain its salt adsorption capacity (SAC) longer. The removal of oxygen from the …

Building Entry Flood Barrier, Richard Esker, Shannon Mccall, Andrew Udovich, Brian Foust

Williams Honors College, Honors Research Projects

The purpose of this project is to develop a flood barrier that would resist flood water from entering through the doorways of a building. The goal is to mitigate extensive flooding within a structure. After the disastrous weather events that impacted American citizens late in the year of 2017, the team was inspired to develop a project to help disaster victims. Through extensive preliminary and market research, it was discovered that flooding is a serious issue that affects people all over the world. A product to stop flooding could benefit people in developed countries, but it could also help citizens …

Potential Replacement Of The Us Navy's Rapid Penetration Test With The Method Of Multichannel Analysis Of Surface Waves, William Fletcher

UNF Graduate Theses and Dissertations

The United States Navy (USN) currently utilizes a Rapid Penetration Test (RPT) on both land and in water as the means to determine whether sufficient soil bearing capacity exists for piles in axial compression, prior to construction of the Elevated Causeway System (Modular) [ELCAS(M)] pile-supported pier system. The USN desires a replacement for the RPT because of issues with the method incorrectly classifying soils as well as the need to have a less labor-and-equipment-intensive method for geotechnical investigation.

The Multichannel Analysis of Surface Waves (MASW) method is selected herein as the potential replacement for the RPT. The MASW method is …

Designing And Testing 3-D Printed Wafer-Box With Embedded Pzt Sensors To Identify The Shape Effect On Energy Harvesting, Ahmad Jami Safayet

Electronic Theses and Dissertations

Piezoelectric energy has been recently paid attention in the field of alternative energy. Day by day the traditional energy sources including Coal tar and oils are becoming scarce. People are heading to an alternative energy source to meet the future energy demand. Piezoelectric energy is one of the competitive energy sources compared to the conventional renewable energy sources including solar, wind, and geothermal power and so on. This energy production method bears enormous research potential because it can be used as the roadway for a new method of power generation. This research project aimed to identify which shaped wafer-box produced …