Mechanical Engineering Commons^™

Aerodynamic Design And Analysis Of A Modified 2006 Mazda Miata, William N. Recher

Honors College Theses

Aerodynamic forces developed by automobiles have destabilizing effects at high speed. These forces tend to skew toward a vehicle’s rear which can present safety concerns, especially for rear-wheel-drive automobiles like the Mazda Miata. To address oversteer and high-speed instability, a vehicle’s design can be tailored to bring about aerodynamic balance and improve traction. LiDAR was used to bring the physical automobile into the digital space. Then, a splitter and diffuser were added to reduce the magnitude of the destabilizing forces. Next, the size and shape of the rear-wing required to balance the vehicle was calculated using a combination of parameters …

Finite Element Analysis Of Thermal-Mechanical Instabilities In Nonmetallic Friction Composite Material, Joseph-Shaahu Shaahu

Electronic Theses and Dissertations

Thermal-mechanical instability (TMI) has been a research topic of interest as it focuses a lot on transportation systems. Thermal-mechanical instability was first noticed in railway and experimentally studied with a pin-to-pin or pin-to-surface setup of sliding contact. The topic has been extended into brakes and clutches which are two of the most common sliding systems most susceptible to thermal buckling and thermoelastic instability (TEI), where thermal buckling and thermoelastic instability are two sub-categories of thermal-mechanical instability. Thermal-mechanical instability is an ongoing research to better understand the phenomenon and the limits at which such instability occurs. This work delved into the …

Comparison Of Methods For Estimating Instantaneous Turn Radius Of Ackermann Steering Vehicles, Kenneth Gennaro Stutts

Doctoral Dissertations and Master's Theses

The instantaneous turn radius of an Ackermann steering vehicle is the distance to a point in space about which the vehicle will travel in an arc during a turn. There are at least six ways to estimate instantaneous turn radius and each method uses different inputs and has distinct advantages and disadvantages. In this thesis, six different methods will be used to estimate the instantaneous turn radius of a vehicle traveling on a closed circuit. This testing will clarify similarities and differences between the methods. This thesis clarifies which method will be the most appropriate for a given set of …

Experimental Study On The Impact Of Low Thermal Inertia Thermal Barrier Coatings On Ppci-Diffusion Gci Combustion, Kunal Vedpathak

All Theses

The application of thermal barrier coatings (TBCs) has been studied in homogenous charge compression ignition (HCCI), conventional diesel combustion (CDC), and spark ignition (SI). Gasoline compression ignition (GCI) combines the low soot and NOx emissions of HCCI with combustion controllability through fuel stratification. GCI has become an interesting prospect due to the reduction in gasoline consumption due to the electrification and hybridization of the light-duty sector. It can be used as a preferred combustion mode in heavy-duty engines to reduce emissions with minimal modifications. GCI exhibits better combustion efficiency than HCCI. Advances in material technology have combined low thermal conductivity …

Safe Navigation Of Quadruped Robots Using Density Functions, Andrew Zheng

All Theses

Safe navigation of mission-critical systems is of utmost importance in many modern autonomous applications. Over the past decades, the approach to the problem has consisted of using probabilistic methods, such as sample-based planners, to generate feasible, safe solutions to the navigation problem. However, these methods use iterative safety checks to guarantee the safety of the system, which can become quite complex. The navigation problem can also be solved in feedback form using potential field methods. Navigation function, a class of potential field methods, is an analytical control design to give almost everywhere convergence properties, but under certain topological constraints and …

Cfrp Delamination Density Propagation Analysis By Magnetostriction Theory, Brandon Eugene Williams

All Dissertations

While Carbon Fiber Reinforced Polymers (CFRPs) have exceptional mechanical properties concerning their overall weight, their failure profile in demanding high-stress environments raises reliability concerns in structural applications. Two crucial limiting factors in CFRP reliability are low-strain material degradation and low fracture toughness. Due to CFRP’s low strain degradation characteristics, a wide variety of interlaminar damage can be sustained without any appreciable change to the physical structure itself. This damage suffered by the energy transfer from high- stress levels appears in the form of microporosity, crazes, microcracks, and delamination in the matrix material before any severe laminate damage is observed. This …

Controlled Manipulation And Transport By Microswimmers In Stokes Flows, Jake Buzhardt

All Dissertations

Remotely actuated microscale swimming robots have the potential to revolutionize many aspects of biomedicine. However, for the longterm goals of this field of research to be achievable, it is necessary to develop modelling, simulation, and control strategies which effectively and efficiently account for not only the motion of individual swimmers, but also the complex interactions of such swimmers with their environment including other nearby swimmers, boundaries, other cargo and passive particles, and the fluid medium itself. The aim of this thesis is to study these problems in simulation from the perspective of controls and dynamical systems, with a particular focus …

Life Cycle Energy Assesment Of Advanced Fiber Reinforced Composite Design And Manufacturing Methodologies, Urjit Lad

All Theses

Automotive industry at large is focused on vehicle light-weighting since a 6%-8% increase in fuel efficiency can be achieved with a 10% reduction in vehicle weight [1]. With the growing demand for cost-effective and sustainable light weighting of automobile structures, interest has increased in the application of fiber reinforced plastic (FRP) composites for use in the Body-in-White (BiW), which can account for up to 40% of the total vehicle weight. Traditional FRP composite manufacturing processes like vacuum assisted resin transfer molding, autoclave consolidation or use of automated fiber placement have been successfully used for marine and aerospace applications. However, these …

Development Of A Soft Robotic Approach For An Intra-Abdominal Wireless Laparoscopic Camera, Hui Liu

Doctoral Dissertations

In Single-Incision Laparoscopic Surgery (SILS), the Magnetic Anchoring and Guidance System (MAGS) arises as a promising technique to provide larger workspaces and field of vision for the laparoscopes, relief space for other instruments, and require fewer incisions. Inspired by MAGS, many concept designs related to fully insertable magnetically driven laparoscopes are developed and tested on the transabdominal operation. However, ignoring the tissue interaction and insertion procedure, most of the designs adopt rigid structures, which not only damage the patients' tissue with excess stress concentration and sliding motion but also require complicated operation for the insertion. Meanwhile, lacking state tracking of …

Enabling Energy Efficiency In Connected And Automated Vehicles Through Predictive Control Techniques, Farhang Motallebiaraghi

Dissertations

The transportation sector is a significant contributor to global energy consumption and emissions, necessitating the development of sustainable transportation systems. In this regard, connected and automated vehicles (CAVs) have emerged as a potential solution to transform the transportation industry. By harnessing advanced mapping and location technologies, Vehicle-to-Vehicle (V2V) and Vehicle-to-Infrastructure (V2I) communication, CAVs offer the promise of improving efficiency, reducing traffic congestion, and enhancing safety and comfort. However, the adoption of CAVs also brings about various challenges, including energy efficiency concerns that need to be addressed to fully realize their potential benefits. This dissertation investigates energy-efficient control techniques for transportation …

Improving Autonomous Vehicles Operational Performance Using Resilience Engineering, Johan Fanas Rojas

Dissertations

Autonomous vehicles are expected to revolutionize the transportation industry by providing a safer and more efficient means of transportation. However, as autonomous vehicles are deployed on public roads, they are exposed to significant risks, both in terms of safety and system performance. Recent studies have highlighted a range of errors and accidents associated with autonomous vehicles, underscoring the need for a systematic approach to improve their operational resilience. Resilience engineering, a discipline focused on designing and analyzing complex systems to better cope with unexpected events and disruptions, offers a promising framework for addressing these challenges. Despite the potential benefits of …

Sensor Updates For Bigheaded Carp-Tracking Autonomous Boat, Jordan Kaufmann

Honors College Theses

Bigheaded carp are an invasive species that overpopulate and compete with the native species of Kentucky Lake as well as many other North American aquatic ecosystems. The movement patterns of Bigheaded carp are being studied nationwide by the United States Geological Survey and multiple universities. These studies ultimately seek to control their spread and reduce or reverse the ecosystem destabilization caused by this invasive species. Such studies are currently conducted manually on Kentucky Lake by graduate students affiliated with the Murray State University (MSU) Biology Department and Hancock Biological Station, and these manual studies are an arduous and time-consuming effort. …

Deep Reinforcement Learning And Game Theoretic Monte Carlo Decision Process For Safe And Efficient Lane Change Maneuver And Speed Management, Shahab Karimi

All Dissertations

Predicting the states of the surrounding traffic is one of the major problems in automated driving. Maneuvers such as lane change, merge, and exit management could pose challenges in the absence of intervehicular communication and can benefit from driver behavior prediction. Predicting the motion of surrounding vehicles and trajectory planning need to be computationally efficient for real-time implementation. This dissertation presents a decision process model for real-time automated lane change and speed management in highway and urban traffic. In lane change and merge maneuvers, it is important to know how neighboring vehicles will act in the imminent future. Human driver …

Improving Future Vehicle Fuel Economy And Operational Design Domain Through Novel Data Pipelines, Kyle James Carow

Masters Theses

Modern automobiles have greatly advanced in recent years, with technological developments that enhance performance, safety, and comfort. However, there is still much room for improvement. Today’s vehicles are heavily reliant on the combustion of fossil fuels, proven to be harmful for the environment on both a local and global scale. In addition, the safety benefits of autonomous vehicles and advanced driver assistance systems are not yet fully realized due to the limited operational design domain of these technologies. In this research, these needs are addressed through the development of two novel data pipelines. In the first study, a novel methodology …

Jack And Alex Rc-Baja, Alex Vornbrock

All Undergraduate Projects

Teams of two mechanical engineering students were tasked with the construction of an RC Baja car qualified by the rules and regulations of the Baja competition as well as specifications set by the individual team member for their portion of the vehicle. This proposal focuses on the Chassis and Drivetrain of the vehicle while team member Jack Stutz oversaw the steering and suspension. Teams will compete against each other in various modes to determine the best vehicles of the competitors. The chassis was made of standard aluminum, the remaining parts made by the students were made with PLA; both materials …

Rc Baja Suspension And Steering, Garrett Bailey

All Undergraduate Projects

The RC Baja team set out to engineer and construct a working remote-control device that can compete in the ASME Baja Competition. The students have a focus on either suspension and steering or drivetrain and chassis. This report is centered on the suspension and steering. First, multiple analyses were completed using engineering methods such as mechanical design, statics, strengths of materials, and dynamics for parts of the device. The calculations found in the analysis are then used to create designs for the parts so that they will meet the requirements and be successful in the competition. After the parts are …

Design And Validation Of An Aerodynamic System For A Formula Sae® Vehicle Using Vehicle Dynamic Simulation And Experimentation, Evan S. Cole

Graduate Theses, Dissertations, and Problem Reports

This thesis presents the design, simulation, and experimental validation for the aerodynamic system for a Formula SAE® vehicle. The Society of Automotive Engineers ® (SAE) hosts a collegiate competition annually called Formula SAE® where students design, fabricate, and test a small “formula style” vehicle. The vehicle performs in relatively slow maneuvers, around different courses and tests to evaluate the vehicle’s overall performance. Over the years, collegiate teams have put significant research into the design and manufacturing of the aerodynamics of these vehicles. In order to justify this undertaking for future teams at West Virginia University’s Formula SAE® program, a comprehensive …

Combustion Characteristics Of Methane, Ethane, Propane, And Butane Blends Under Conditions Relevant Of A Dual-Fuel Diesel And Natural Gas Engine, Christopher Joseph Ulishney

Graduate Theses, Dissertations, and Problem Reports

As natural gas production infrastructure is already in place in most of the world and will continue expanding for the foreseeable future, natural gas is an alternative to traditional liquid petroleum fuels in heavy-duty engines. Dedicated natural gas or dual-fuel diesel-natural gas heavy-duty engines are alternatives to diesel-only power generation equipment. One challenge is the large variation in the natural gas composition available for such applications, which is known to significantly affect engine’s combustion characteristics and the emissions composition. As the literature on dual-fuel combustion under low load engine operating conditions that use more realistic natural gas mixtures (i.e., mixtures …

Enhancing Traffic Safety In Unpredicted Environments With Integration Of Adas Features With Sensor Fusion In Intelligent Electric Vehicle Platform With Implementation Of Environmental Mapping Technology, David S. Obando Ortegon

Electronic Theses and Dissertations

A major objective on society is to reduce the number of accidents and fatalities on the road for drivers, and pedestrians. Therefore, the automotive engineering field is working on this problem through the development and integration of safety technologies such as advanced driving assistance systems. For this reason, this work was intended to develop and evaluate the performance of different ADAS features and IV technologies under unexpected scenarios. This by the development of safety algorithms applied to the intelligent electric vehicle designed and built in this work, through the use of ADAS sensors based on sensor fusion. Evaluation of AEB, …

Machine Learning Approach To Investigate Ev Battery Characteristics, Shayan Falahatdoost

Major Papers

The main factor influencing an electric vehicle’s range is its battery. Battery electric vehicles experience driving range reduction in low temperatures. This range reduction results from the heating demand for the cabin and recuperation limits by the braking system. Due to the lack of an internal combustion engine-style heat source, electric vehicles' heating system demands a significant amount of energy. This energy is supplied by the battery and results in driving range reduction. Moreover, Due to the battery's low temperature in cold weather, the charging process through recuperation is limited. This limitation of recuperation is caused by the low reaction …

Supporting Us Army Next-Generation Ground Vehicle Simulation Modeling Using An Integrated Ontology Suite, Edward Louis

All Theses

The development of the US Army’s next-generation of ground vehicle systems is supported by simulations that predict vehicle performance and inform engineering design choices in the design and acquisition process. In this paper, we describe the development of an Integrated Ontology Suite to support modeling and simulation of next generation military ground vehicles. The ontology suite is intended to address model reuse challenges and increase the shared understanding of ground vehicle system simulations. It is intended to function in a Model Library structure that stores, documents, assembles, and executes vehicle simulations. The ontology suite consists of four domain ontologies: Vehicle …

Multiple Heat Exchanger Cooling System For Automotive Applications – Design, Mathematical Modeling, And Experimental Observations, Zaker Syed

All Dissertations

The design of the automotive cooling systems has slowly evolved from engine-driven mechanical to computer-controlled electro-mechanical components. With the addition of computer-controlled variable speed actuators, cooling system architectures have been updated to maximize performance and efficiency. By switching from one large radiator to multiple smaller radiators with individual flow control valves, the heat rejection requirements may be precisely adjusted. The combination of computer regulated thermal management system should reduce power consumption while satisfying temperature control objectives. This research focuses on developing and analyzing a multi-radiator system architecture for implementation in ground transportation applications. The premise is to use a single …

Multi-Robot Symbolic Task And Motion Planning Leveraging Human Trust Models: Theory And Applications, Huanfei Zheng

All Dissertations

Multi-robot systems (MRS) can accomplish more complex tasks with two or more robots and have produced a broad set of applications. The presence of a human operator in an MRS can guarantee the safety of the task performing, but the human operators can be subject to heavier stress and cognitive workload in collaboration with the MRS than the single robot. It is significant for the MRS to have the provable correct task and motion planning solution for a complex task. That can reduce the human workload during supervising the task and improve the reliability of human-MRS collaboration. This dissertation relies …

Effect Of Passive Clean Air Injection Into The Wake Region Of A Moving Ground Vehicle, Angelos Kaminis

Doctoral Dissertations and Master's Theses

The wake region on a moving ground vehicle is responsible for 70% of the aerodynamic drag when the speed of 90km/h is achieved. The topic of wake region manipulation has been revisited multiple times and with varying techniques. When manipulating the flow utilizing a fully passive method, pressure drag can be reduced, increasing the overall performance of the vehicle. To ensure high velocity fluid injection, a venturi shaped roof was implemented with an inlet size of 352mm x 12.7mm, and 2 outlets of size 88.011mm x 25.4mm resulting in an area of 4,470.959 for both inlet and outlet to maintain …

Baja Bug Suspension, James Ankers, Rebecca Hansen, Dakota Robert Hollingsworth, Thomas Alfred Spycher

Mechanical Engineering

The goal of this senior project was to design and build a long travel front suspension system for a VW Bug. This started by defining the scope of the project and performing preliminary research. In this step, similar products were investigated, and research was done on stakeholders and customers. Next, concept development, design, and evaluation were performed. With this, the first iteration of our CAD model was designed, and physical prototypes were made. Using all this information, and feedback from advisors and sponsors, multiple iterations of our CAD were performed until the design was ready to manufacture. Drawings were taken …

B.A.C.O.N. (Battery-Powered Autonomous Cart Conversion) Autonomous Vehicle Design, Robyn C. Ribet, Damond Li, Tanner Hillman, Christopher Or

Mechanical Engineering

The goal of our project is to convert an electric go cart into an autonomous testing platform. We must enable autonomous braking, steering, and acceleration with electro-mechanical systems. We began the project with ideation to create our initial design and have since received ample feedback from faculty, students, and our sponsor. With this feedback we were able to refine our preliminary ideas and produce a detailed design supported with ample analysis, research, and external advice. We have developed our project in four main subsystems: Steering, braking, acceleration, and emergency braking. Following, we procured, manufactured, and assembled all of our designed …

Model Predictive Controller Design For Internal Combustion Engines Based On The Second Law Of Thermodynamics, Muataz Abotabik

Dissertations

Energy resources depletion and worldwide strict emissions policies pose challenges that automotive manufacturers try to overcome through researching advanced powertrain technologies such as lean-burn gasoline, direct injection, homogeneous charge compression ignition engines, powertrain electrification, etc. Most of these developments have been focused on conventional internal combustion engines (ICE) emissions and performance enhancements. Most ICE control strategies are built based on the First Law of Thermodynamics (FLT) i.e., to deliver a specific load requirement, enhancing thermal efficiency, etc. The FLT doesn’t account for in-cylinder high temperature thermodynamics process irreversibilities that cause losses in the work potential; up to 25% of the …

Modeling And Control Of A Planar Bounding Quadrupedal Robot, Patrick John Ward

Master's Theses

Legged robots have the potential to be a valuable technology that provides agile and adaptive locomotion over complex terrain. To realize legged locomotion's full abilities a control design must consider the nonlinear piecewise dynamics of the systems. This paper aims to develop a controller for the planar bounding of a quadrupedal robot.

The bounding of the quadruped robot is characterized by a simplified hybrid model that consists of two subsystems for stance and flight phases and the switching laws between the two states. An additional model, the Multibody model, with fewer simplifications, is used concurrently to best approximate real-world behavior. …

Control, Decision-Making, And Learning Approaches For Connected And Autonomous Driving Systems With Humans-In-The-Loop, Fangjian Li

All Dissertations

By virtue of vehicular connectivity and automation, the vehicle becomes increasingly intelligent and self-driving capable. However, no matter what automation level the vehicle can achieve, humans will still be in the loop despite their roles. First, considering the manual driving car as a disturbance to the connected and autonomous vehicles (CAVs), a novel string stability is proposed for mixed traffic platoons consisting of both autonomous and manual driving cars to guarantee acceptable motion fluctuation and platoon safety. Furthermore, humans are naturally considered as the rider in the passenger vehicle. A human-centered cooperative adaptive cruise control (CACC) is designed to improve …

Investigation Of The Low-Temperature Combustion Phenomena Of A Fischer-Tropsch Synthetic Aerospace Fuel In A Constant Volume Combustion Chamber For Greenhouse Gas Reduction, Lily H. Parker

Honors College Theses

Greenhouse gases (GHG) have a harmful effect on our environment as they trap heat in the atmosphere accelerating climate change. As such, the Federal Aviation Administration’s 2025 strategic plan to reduce GHG emissions from air transportation. This call to action for a more environmentally friendly option highlights the importance of synthetic fuels as they are more sustainable compared to traditional fossil fuels. An investigation was conducted into the thermal-physical properties of Synthetic Fischer-Tropsch (F-T) Sustainable Aviation Fuels (SAF) and the Low Temperature Combustion (LTC). LTC is composed of the Low Temperature Heat Release (LTHR) and Negative Temperature Coefficient (NTC) region, …