Mechanical Engineering Commons^™

Reducing Food Scarcity: The Benefits Of Urban Farming, S.A. Claudell, Emilio Mejia

Journal of Nonprofit Innovation

Urban farming can enhance the lives of communities and help reduce food scarcity. This paper presents a conceptual prototype of an efficient urban farming community that can be scaled for a single apartment building or an entire community across all global geoeconomics regions, including densely populated cities and rural, developing towns and communities. When deployed in coordination with smart crop choices, local farm support, and efficient transportation then the result isn’t just sustainability, but also increasing fresh produce accessibility, optimizing nutritional value, eliminating the use of ‘forever chemicals’, reducing transportation costs, and fostering global environmental benefits.

Imagine Doris, who is …

The Effect Of Parameters In Cryogenic Treatment On Mechanical Properties Of Tool Steel: A Review, Ronaldus Caesariano Ekaputra, Myrna Ariati Mochtar

Journal of Materials Exploration and Findings

Tool steel is classified as special alloy steel which proposed as dies or mold materials as their high mechanical properties and dimensional stability. In order to improve tool steel’s mechanical properties, heat treatment process, especially, cryogenic treatment is conducted. Cryogenic treatment is done by exposing tool steel material at sub-zero liquid/gas media after heated at austenite temperature. This process significantly affects the martensite phase transformation increase and avoids retained austenite emersion. In particular, the higher martensite volume fraction, the higher hardness and wear resistance value of tool steel. It had been proven that adjusting critical process parameters of cryogenic treatment …

Nitrogen Gas Quenching Pressure Effect On Bs S155 Alloy Steel In Vacuum Furnace, Agus Mulyadi Hasanudin, Eddy Sumarno Siradj

Journal of Materials Exploration and Findings

The production of metal and alloy products requires the use of heat treatment, when during the heat treatment process, quenching is a crucial step. The quenching medium can be anything from water, a salt bath, oil, air and gas. In a vacuum furnace, pressurized gas, most frequently nitrogen (N₂) gas, serves as one of the quenching mediums. One of the drawbacks of the quenching process is the distortion and dimensional change of the parts. This paper aims to investigate the influence of nitrogen gas quenching pressure on the distortion and dimensional change of aerospace actuator gear planet parts …

Pipeline Risk Analysis Optimization With Monte Carlo Method Using Gamma Distribution, Farhan Rama Digita, Jaka Fajar Fatriansyah, Abdul Rahim Ridzuan, Hanna Ovelia, Imam Abdillah Mas'ud, Irma Hartia Tihara, Baiq Diffa Pakarti Linuwih

Journal of Materials Exploration and Findings

The inspection process of piping components in the oil and gas industry is one of the most crucial things, given the high risk posed by pipeline system failures, which have a huge impact on losses, both from environmental and financial aspects. Risk-based inspection with the Monte Carlo method is one of the efforts that can be made to minimize failures in piping systems, by involving data distribution to calculate the probability of component failure. Although the normal distribution is commonly used for generating random variables, its use in corrosion rate calculation can lead to overestimation due to negative corrosion rate …

Isolation And Characterization Of Caffeine-Degrading Bacteria From Coffee Plantation Areas In Malaysia, Elvina Clarie Dullah, Mohd Fazli Farida Asras

Makara Journal of Technology

Decaffeination by microbial degradation is currently the most optimal and low-cost approach, involving only microbial cells and/or their enzymes. The bacterium was characterized using a series of biochemical tests. Positive results were obtained from carbohydrate fermentation, citrate utilization, and catalase tests, while negative results were obtained from Voges-Proskauer (VP) and indole tests. Three different caffeine concentrations of 0.25%, 0.4%, and 2% were tested and measured through Gas Chromatography-Mass Spectrophotometry (GC-MS) analysis. The highest caffeine reduction (89.25%) was found when 0.25% caffeine was used in the media. Only a small amount of caffeine was reduced to 0.4% and 2%, with 34.78% …

Optimization Of The Building Envelope And Roof Shading To Reduce The Energy Consumption Of College Low-Rise Buildings In Indonesia, Nasruddin Nasruddin, Azimil Gani Alam, Mohammad Imroz Sohel

Makara Journal of Technology

Energy consumption in buildings is a crucial concern globally, prompting researchers to explore innovative solutions to mitigate its impact. This study investigates the optimization of building envelopes and roof shading systems of existing buildings in Indonesia to realize notable energy savings. Multiple scenarios were explored, with modifications to building envelopes and roof shading, highlighting the overall thermal transfer value as a key parameter. Using EnergyPlus simulations, the efficacy of natural ventilation in corridors and roof shading modifications was assessed in reducing energy consumption. The findings revealed that renovating existing buildings by optimization of the building envelope and roof shading by …

Combined Risk Based Inspection And Fault Tree Analysis For Repetitive 3-Phase Line Piping Leakage At West Java Offshore Topside Facility, Dona Yuliati, Akhmad Herman Yuwono, Datu Rizal Asral, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Hydrocarbon releases might result in serious consequences in various aspects. In addition to the contribution to environmental pollution, repetitive leakages need high repair costs. This study aim is to minimize potential repetitive leakage for other typical 3-phase piping systems. We conducted the risk assessment by adopting Risk Based Inspection (RBI) API 581 to identify risk level, calculating piping lifetime, recommended inspection plan and mitigations. The most relevant root causes can be obtained through quantitative Fault Tree Analysis (FTA). Observation and investigation was taken from eight 3-phase piping systems that experienced repetitive leakages. It has been found that the risk level …

A Review On Ship Recycling Industry In Bangladesh From Global Perspective, Ahammad Abdullah, Zobair Ibn Awal, M Ziauddin Alamgir, Md. Jobayer Mia, Farihatul Mim, Utpal K. Dhar

Journal of Ocean and Coastal Economics

At present, the global center of the ship breaking and recycling industry is in South Asia, specifically Bangladesh, India, and Pakistan. These three countries account for 70–80 percent of the international recycling market for ocean-going vessels, with China and Turkey covering most of the remaining market. Only about 5 percent of global volume is scrapped outside these five countries. Bangladesh has environmentally beneficial coastal region and affordable labor that make the shipbreaking and recycling business as a potential sector for the country. In addition, ship recycling and its related businesses are helping to solve our nation’s unemployment issues at all …

The Effects Of Engineering Summer Camps On Middle And High School Students’ Engineering Interest And Identity Formation: A Multi-Methods Study, Timothy Robinson, Adam Kirn, Jenny Amos, Indira Chatterjee

Journal of Pre-College Engineering Education Research (J-PEER)

This multi-methods study explores changes in engineering interest and identity of middle and high school students (n = 79) attending introductory-level engineering summer camps at a large western land grant university. Middle school is a critical time when student interest, identity, and subsequently career choice begin to emerge and hence it is important that at this age students are given accurate information about engineering majors in college and future career opportunities in engineering. Data were collected over a period of two years in six summer camps. Three separate populations of middle and high school students participated in the summer …

Challenges In Optimization For The Performance On Sustainability Dimensions In Reverse Logistics Social Responsibility, Sumarsono Sudarto, Katsuhiko Takahashi, Mochammad Dewo

Makara Journal of Technology

Reverse logistics social responsibility is preferred as the most acceptable solution for addressing the challenges in stakeholders’ debate regarding social responsibility in supply chains because it involves as many actors as possible in the supply chain to perform social responsibility to achieve sustainability. This paper explores the challenges in achieving optimal policies in sustainability dimensions for collection and recycling facilities in reverse logistics. Sustainability dimensions include economic, environmental, and social aspects. The reverse logistics is modeled on System Dynamics, and a simplified statistical analysis using a contour chart is employed in numerical experiments. Results show a narrow area of optimal …

Influence Of Forming Forces On Torsional, Tensile, And Compressive Deformation Of Paperboard Packages, Arvo Niini, Panu Tanninen, Juha Varis, Ville Leminen

Journal of Applied Packaging Research

Paperboard packages were tested mechanically to investigate influence of forming forces on torsional, tensile, and compressive deformation. The packages were paperboard trays which were press formed with different pressing forces and blank holder forces. Deformation of the trays was observed with torsion, compression, and tensile tests. A statistical analysis of test results was conducted to derive optimal forming forces. Increased pressing force yielded desirable deformation characteristics with the trays. Blank holder force had largest impact on the compressive deformation. Interaction of the pressing force and the blank holder force influenced the torsional and the compressive deformation. The optimal forming forces …

The Effect Of Heat Treatment And Chemical Treatment On Natural Fibre To The Durability Of Wood Plastic Composites – A Review, Nuratiqah Asyiqin Mohd Nasharudin, Nur Fatihah Sulaiman, Nurul Aziemah Mohammad, Wan Nor Raihan Wan Jaafar, Falah Abu Dr., Siti Norasmah Surip

Journal of Materials Exploration and Findings

The application of WPC is not only limited to indoor applications but has been extended to exterior applications where properties of WPC could compromise during service life. WPC was derived from wood fiber of various sizes to reinforce polymers. Wood fiber has the advantage of a cheaper price, being abundantly available, and ease of processing, however, the critical factor is its hydrophilic nature, where moisture absorption is likely to occur. Thus, treatments for reducing the hydrophilicity of wood fibers are applied. By treatment of wood fiber, the surface impurities were removed, leaving the roughened surface of fibers, thus providing a …

Effect Of Heat Input On Microstructure And Mechanical Properties Of Submerged Arc Welded Sm570-Tmc Steel, Toni Yuhandri, Winarto Winarto, Diana Natalia

Journal of Materials Exploration and Findings

SM570TMC is high-strength steel (HSS), which is commonly used in structures that require higher-strength components. In this research, submerged arc welding (SAW)-welded SM570 TMC steels' microstructure and mechanical characteristics were examined. SM570 plates with 12mm thickness were multi-pass welded by using a 3.0 mm diameter of ESAB OK Autrod 13.40 (AWS A5.23: EG) filler metal. The joint design is a single V multi-pass butt weld with a backing strip. Two welded joints were prepared by using heat inputs of 2.2 and 2.9 kJ/mm. The microstructures of two welded joints were observed by using optical microscopy and scanning electron microscope (SEM). …

The Effect Of Current Density And Hard Chrome Coating Duration On The Mechanical And Tribological Properties Of Aisi D2 Steel, Indah Uswatun Hasanah, Dedi Priadi, Donanta Dhaneswara

Journal of Materials Exploration and Findings

The effect of hard chromium coating on AISI D2's mechanical properties and wear resistance has been investigated using the electrolysis technique with varying current and coating duration. The variations of current used are 0.8 A, 1.2 A, and 1.6 A, while the coating duration used are 300, 600 and 900 seconds. Characterization of the films was conducted using SEM-EDS, and XRD. It can be observed from SEM characterization that the chrome grains resulted from the electroplating process are fine. The XRD identify chrome compund on the surface coating. The highest hardness value was 520.6 HV on a sample with a …

Optimization Of Alti Pld Coating By Increasing Ti Content, N2 And Annealing Which Used For Skd61 Pins In Aluminum Die Casting, Rusman Kosasih, Maria Margaretha Suliyanti Prof, Dedi Priadi, Wisnu Usni

Journal of Materials Exploration and Findings

The Alumunium Titanium Nitrogen (AlTiN) coating is known as one of the best coating materials for protective coating, while Pulsed Laser Deposition (PLD) is a laser coating process used for electric layer and superconductor applications, producing thin films up to 20 µm in thickness. The combination of these two matters has already been researched and is still in progress. One major challenge in the aluminium casting industry is to minimize the damage caused to tool steel pins made from SKD61, when aluminium material sticks to the pin, and halting production. Therefore, research on effective coatings for tool steels and testing …

Multi-Mode Total Focusing Method (Mtfm) To Detect High-Temperature Hydrogen Attack (Htha) – A Review, Anjar Oktikawati, Rini Riastuti, Nursidi Yuanto

Journal of Materials Exploration and Findings

High temperature hydrogen attack (HTHA) is a commonly observed harm component in carbon steels exposed to high temperature and pressure in a hydrogen-rich environment. Hydrogen together with carbon responds to produce methane. The formation of methane bubbles in steel can lead to loss of fracture toughness and lead to intergranular cracking. The main challenge of this problem lies in early warning systems that can detect these bubble clusters before they reach the advanced stage. Several advanced ultrasonic inspections have been developed over the years due to the challenges of inspecting materials for defects and discontinuities. These cover time-of-flight diffraction (ToFD), …

Estimating Remaining Life And Fitness-For-Services Evaluation Of Fuel Piping Systems, Sekar Putri Purwidyasari, Ahmad Isni Kurniawan, Deni Ferdian

Journal of Materials Exploration and Findings

Assets life extension are required to predict the design life expiry based on condition and effects of deterioration. The remaining life assessment will answer the questions about timing of the component or equipment will lead to failure and shall be evaluated by inspection and maintenance monitoring. This study elaborates process calculation and analysis by using remaining life assessment and fitness for services method according to API 579-1/ASME FFS-1 for process piping area. The result of remaining useful life estimation and estimated life has been proposed. There are 11 piping systems based on the condition monitoring with thickness measurements. The result …

Launching A 3d Printing Program For Students: Recommendations And Best Practices For Libraries, Wilhelmina Randtke, Lee Bareford

Georgia Library Quarterly

The Georgia Southern University Libraries launched a 3D printing program for students in July 2022. Prior to launch, library employees at two of Georgia Southern University’s campuses investigated options for implementing safe, affordable, and sustainable 3D printing in existing academic libraries without retrofitting costly ventilation systems into existing facilities. This article describes the reasons why the Georgia Southern University Libraries thought that a 3D printing program could fulfill a service need for students across university colleges and departments and outlines some of the challenges, best practices, and unique innovations that the library’s employees experienced throughout the program launch process. The …

Effect Of Austenization And Repeated Quenching On The Microstructures And Mechanical Properties Of Wear-Resistant Steel, Yanuar Nugraha, Myrna Ariati Mochtar

Journal of Materials Exploration and Findings

This study was focused on determining the effect of repeated austenitization and quenching on mechanical properties and microstructure. The experiment was carried out in a rolled quencher facility with a heat treatment process of one to two times, with parameters of an austenizing temperature of 9500C and quenching at a temperature of 8500C with pressurized water media. Testing of specimens, including microstructure observations and hardness testing. The repeated heat treatment process showed an increase in hardness of 0.79% on one-time repeated heat treatment and 1.65% on two repeated heat treatments. This occurs due to the presence accompanied by refinement of …

Freespan Analysis For Subsea Pipeline Integrity Management Strategy, Nurul Hadi, Muhammad Helmi, Edo Cathaputra, Dedi Priadi, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Abstract. Over a rough seabed or on seabed subject to scour, freespans can occur when contact between a subsea pipeline and the seabed is lost over an acceptable distance. When this exceeds the allowable freespan length, design stresses can be exceeded, and a vortex induced vibration (VIV) response can be initiated, resulting in the risk of fatigue failure. If this is not predicted and controlled properly, it will affect pipeline integrity, leading to expensive rectification and intervention work. Freespan analysis consisted primarily of a screening check in which the as-found freespans from Remotely Operated Vehicle (ROV) or multibeam Side …