Mechanical Engineering Commons^™

Waste Heat Recovery From A Vented Electric Clothes Dryer Utilizing A Finned-Tube Heat Exchanger, Abdul Raheem A. Shaik, Stephen L. Caskey, Eckhard A. Groll

The Summer Undergraduate Research Fellowship (SURF) Symposium

Conventional residential clothes dryers continuously vent moist, hot air during the drying process. The vented air leaves the home but still has useful temperature and humidity that could be recovered to offset other heating demands in the home. A study is carried out to quantify the amount of heat extracted from the waste heat stream of a conventional, vented clothes dryer. To extract the heat, a water cooled, fin-and-tube heat exchanger is located within the exhaust duct. A steady state thermodynamic dry coil and wet coil model was built in Engineering Equation Solver (EES). The model accounts for the heat …

Spectral Phonon Relaxation Time Calculation Tool Based On Molecular Dynamics, Divya Chalise, Tianli Feng, Xiulin Ruan

The Summer Undergraduate Research Fellowship (SURF) Symposium

Thermal conductivity is an important material property which affects the performance of a wide range of devices from thermoelectrics to nanoelectronics. Information about phonon vibration modes and phonon relaxation time gives significant insight into understanding and engineering material’s thermal conductivity. Although different theoretical models have been developed for studying phonon modes and relaxation time, extensive knowledge of lattice dynamics and molecular dynamics is required to compute phonon modal frequencies and relaxation times. Therefore, a computational tool which can take simple inputs to calculate phonon mode frequencies and relaxation time will be beneficial. Through this research work, such computational tool has …

Numerical Simulations Of Transcritical Natural Convection, Ruiwen Wei, Carlo Scalo, Mario Tindaro Migliorino, Kukjin Kim, Jean-Pierre Hickey

The Summer Undergraduate Research Fellowship (SURF) Symposium

In modern engineering applications, system overheating is a key issue that needs to be solved with efficient and reliable cooling technologies. Among the possible mechanisms that these are based on, natural convection cooling is one of the most frequently employed, with applications ranging from cooling of computer micro-components to large nuclear reactors. While many studies have been performed on natural convection employing supercritical or subcritical fluids, little attention has been given to fluids in their transcritical regime. The latter has the potential to yield high performances while avoiding detrimental effects of two-phase systems (e.g. cavitation). In the present study, 2D …

Secondary Atomization: Drop Breakup In A Continuous Air Jet, Grant S. Sondgeroth, Longchao Yao, Catriona M.L. White, Daniel R. Guildenbecher, Jun Chen, Paul E. Sojka

The Summer Undergraduate Research Fellowship (SURF) Symposium

Understanding drop breakup will optimize aircraft engine performance, reduce agro-chemical overspray, and improve pharmaceutical tablet efficacy. Large fuel fragments in engines lead to lowered fuel economy and higher pollutant emissions, while small drops yield more agro-spray drift into surrounding residential and environmental zones. Better pharmaceutical tablets will improve drug uptake and patient comfort.

Engineers and scientists are currently unable to predict the number, size, and velocity of fragments formed during important drop breakup processes. Therefore, we are required to measure these quantities. We use digital inline holography (DIH) to record three-dimensional diameter and position data for fragments formed during multi-mode …

Enhancing The Performance Of A Transportable Environmental Control Unit (Ecu) Operated In High-Temperature Climates, Quan Jun Sun, Ammar M. Bahman, Eckhard A. Groll

The Summer Undergraduate Research Fellowship (SURF) Symposium

Numerous people live or venture into environments, such as the Middle East, where the temperatures can skyrocket as high as 54°C. This leaves many air conditioners unable to operate efficiently. Although much research has been conducted for incorporating vapor injection processes into refrigeration systems, such as ones used in supermarkets, little has been researched regarding the application in extreme heat environments. While most basic air conditioning units do not require the addition of a vapor injection process along with an economizer, this project requires the air conditioning (AC) unit to operate under extreme high temperature conditions. The project investigates the …

Dynamic Modeling And Validation Of Micro-Chp Systems, Apurva Badithela, Neera Jain, Austin Nash

The Summer Undergraduate Research Fellowship (SURF) Symposium

Micro-Combined Heat and Power (micro-CHP) units locally generate electricity to simultaneously provide power and heat for residential buildings. Apart from the potential benefits of reducing carbon emissions and increasing robustness to brownouts and blackouts, micro-CHP systems can be controlled to meet energy demands. Micro-CHP systems consist of a prime mover that generates electricity, such as a fuel cell, an internal combustion engine, or a Stirling engine, and a waste heat recovery system that enables utilization of heat generated as a byproduct of electricity generation. Often, a thermal energy storage system is integrated with micro-CHP systems, thereby decoupling, in time, the …

Dynamic Modeling Of Contact-Mode Triboelectric Generators By Lagrange’S Equations, Sean M. Gauntt, James Gibert

The Summer Undergraduate Research Fellowship (SURF) Symposium

Electret based energy scavenging devices utilize electrostatic induction to convert mechanical energy into electrical energy. Uses for these devices include harvesting ambient energy in the environment and acting as sensors for a range of applications. These types of devices have been used in MEMS applications for over a decade. However, recently there is an interest in Triboelectric generators/harvesters, i.e., electret based harvesters that relies on triboelectrification as well as electrostatic induction. The literature is filled with a variety of designs for the latter devices, constructed from materials ranging from paper and thin films; rendering the generators lightweight, flexible and inexpensive. …

Dynamic Behavior Of A Clamped-Clamped Bi-Stable Laminate For Energy Harvesting, Ajay V. Kumar, Andres F. Arrieta Ph.D., Myungwon Hwang

The Summer Undergraduate Research Fellowship (SURF) Symposium

Multi-stable laminates have many applications in morphing structures, energy harvesting devices, and metamaterials due to the specific characteristics attributed to the exhibited stable states. Changes between stable states allow for large deflections, on-demand variation of the stiffness of compliant structures embedded within these elements, and control of effective dynamic properties in periodic lattices. These changes in state can be accessed via a snap-through instability triggered by introducing a well-defined activation energy. The resulting oscillations could enable broadband energy harvesting via piezoelectric transduction and resistive circuits. In this paper, a clamped-clamped bi-stable laminate is studied to understand the behavior of the …

A Fast Model For The Simulation Of External Gear Pumps, Zechao Lu, Xinran Zhao, Andrea Vacca

The Summer Undergraduate Research Fellowship (SURF) Symposium

External gear pump is an important category of positive displacement fluid machines used to perform the mechanical–hydraulic energy conversions in many fluid power applications. An efficient numerical simulation program is needed to simulate the system in order to provide a direction for design purpose. The model consists of a lumped parameter fluid dynamic model and a model that simulates the radial micro-motions of the gear’s axes of rotation. The system consists of a set of ordinary differential equations related to the conservation on mass of the internal control volumes of the pump, which are given by the tooth space volumes …

Assessment Of Critical Technologies For Gas Turbine Engines Using Numerical Tools, Vinicius Pessoa Mapelli, Guillermo Paniagua, Jorge Sousa

The Summer Undergraduate Research Fellowship (SURF) Symposium

In 2014 gas turbine engine has reached a market value of 82.5 billion dollars, of which 59.5% are related to aircraft propulsion. The continuous market expansion attracts more and more the interest of researchers and industries towards the development of accurate numerical techniques to model thermodynamically the entire engine. This practice allows a performance and optimization analysis before the actual experimental testing, reducing the time and required investment in the design of a new engine. In this paper, a recently developed open source numerical tool named “Toolbox for the Modeling and Analysis of Thermodynamic Systems” (T-MATS) is used to assess …

Fracture Mechanics-Based Simulation Of Pv Module Delamination, Dominic I. Jarecki, Johanna B. Palsdottir, Peter Bermel, Marisol Koslowski

The Summer Undergraduate Research Fellowship (SURF) Symposium

Photovoltaic (PV) cells are rapidly growing as a renewable alternative to fossil fuels like coal, oil, and natural gas. However, greater adoption has also reduced government subsidies, placing the onus of making solar panels economically competitive on innovative research. While multiple methods have been considered for reducing costs, with each reduction in cost comes the associated peril of reduction in quality and useful lifetime. Several problems considered solved have now resurfaced as potential failure mechanisms with the introduction of cheaper PV cell technologies. However, to remain economically viable, PV modules will not only have to become cheaper, they will have …

Hot Surface Ignition, Yerbatyr Tursyn, Vikrant Goyal, Alicia Benhidjeb-Carayon, Richard Simmons, Scott Meyer, Jay P. Gore

The Summer Undergraduate Research Fellowship (SURF) Symposium

Undesirable hot surface ignition of flammable liquids is one of the hazards in ground and air transportation vehicles, which primarily occurs in the engine compartment. In order to evaluate the safety and sustainability of candidate replacement fuels with respect to hot surface ignition, a baseline low lead fuel (Avgas 100 LL) and four experimental unleaded aviation fuels recommended for reciprocating aviation engines were considered. In addition, hot surface ignition properties of the gas turbine fuels Jet-A, JP-8, and JP-5 were measured. A test apparatus capable of providing reproducible data was designed and fabricated to experimentally investigate the hot surface ignition …

The Role Of Surface Area In Catalytic Gasification Of Biomass, Elizabeth A. Wachs, Nitish Kumar, Indraneel Sircar, Prithviraja Basak, Jay P. Gore Phd

The Summer Undergraduate Research Fellowship (SURF) Symposium

Gasification of biomass has the potential to provide a carbon-negative source of liquid fuels. The current limited use of gasification is due in part to the high temperatures necessary to achieve high conversion levels. These temperatures can be lowered by the use of catalysts, but the mechanisms by which catalysts affect the reaction rate are not fully understood. Here, the structural component of potassium carbonate’s role in the gasification process was examined. Samples of pinewood sawdust were impregnated with potassium carbonate, then pyrolyzed with N2 in a fixed bed reactor at 750°C (heater thermocouple reading). Half of the char was …

Modeling Of Mixed Friction Interactions Occurring In Axial Piston Pumps, Andrew C. Adelsperger, Lizhi Shang, Dan Mizell, Monika Ivantysynova

The Summer Undergraduate Research Fellowship (SURF) Symposium

Axial piston pumps are integral to a variety of hydraulic systems due to their versatility and reliability, but most attempts to model them for design purposes have failed. However, software which fully models the fluid structures within these pumps, such as the FSTI gap design program, has improved significantly. Unfortunately, current discrepancies between simulated and measured friction forces on the cylinder due to the fluid drag and piston movement need to be eliminated so that more accurate simulation of these pumps in operation is possible. Friction measurements and FSTI simulation outputs were analyzed with MATLAB filters and graphs, resulting in …

Advanced Visualization Techniques Of Hot-Jet Combustion Of Lean And Ultra-Lean Substances, Timothy I. Machin, Li Qiao

The Summer Undergraduate Research Fellowship (SURF) Symposium

Research has been conducted on ignition of natural gas as a potential replacement for fossil fuels. A reason natural gas is not widely used and adapted is because of the harmful emissions created when combusted in rich mixtures, but if the gas can be burned at a lean or ultra-lean equivalence ratio, these emissions can be reduced or even eliminated. One method of burning lean and ultra-lean substances is by use of hot-jet ignition. This method ignites the substance near its combustion temperature, reducing the harmful emissions. This method is not yet fully understood, and so research must be done …

Experimental Study Of Co2 Recycling Using Metal-Oxide Enhanced Coconut Char Gasification: Catalytic Effect Of Potassium Carbonate On Gasification, Mengqi Gao, Indraneel Sircar, Jay P. Gore

The Summer Undergraduate Research Fellowship (SURF) Symposium

Biomass gasification is an important process in the production of bio-derived fuels and renewable energy. Biomass gasification with CO₂ is an endothermic process requiring high temperatures, resulting in low process-efficiency. Metals found in the ash in biomass feedstock have shown rate-promoting effects on the C-CO₂ reaction and have motivated the study of low-temperature catalytic gasification. The present study investigates the catalytic effects of potassium (K) on the biomass gasification reactivity of a coconut-derived char (>99.9% carbon) within the temperature range of 600 – 1000 ^oC. A wet-impregnation technique is used to prepare K-treated chars. Gasification of …