Mechanical Engineering Commons^™

Thermomechanical Process Simulation And Quantification Of Nanoscale Precipitation Influencing Ductility And Strength During Alloy Processing, Alyssa Stubbers

Theses and Dissertations--Chemical and Materials Engineering

Experimental process simulation and quantification of microstructure development during processing are challenging due to limitations with machinery temperature capability, inadequate resolution and sampling volume of currently available characterization techniques, and difficulty characterizing material microstructures as close to processing-relevant conditions as possible. This dissertation addresses how process simulation can be performed using Gleeble thermomechanical technologies and how microstructure development during these processing simulations can be quantified both in-situ and ex-situ.

The first portion of this dissertation demonstrates how Gleeble technologies can be applied to simulate complex material processing conditions in order to produce process-property profiles that can be used to inform …

Isolation And Characterization Of Caffeine-Degrading Bacteria From Coffee Plantation Areas In Malaysia, Elvina Clarie Dullah, Mohd Fazli Farida Asras

Makara Journal of Technology

Decaffeination by microbial degradation is currently the most optimal and low-cost approach, involving only microbial cells and/or their enzymes. The bacterium was characterized using a series of biochemical tests. Positive results were obtained from carbohydrate fermentation, citrate utilization, and catalase tests, while negative results were obtained from Voges-Proskauer (VP) and indole tests. Three different caffeine concentrations of 0.25%, 0.4%, and 2% were tested and measured through Gas Chromatography-Mass Spectrophotometry (GC-MS) analysis. The highest caffeine reduction (89.25%) was found when 0.25% caffeine was used in the media. Only a small amount of caffeine was reduced to 0.4% and 2%, with 34.78% …

Optimization Of The Building Envelope And Roof Shading To Reduce The Energy Consumption Of College Low-Rise Buildings In Indonesia, Nasruddin Nasruddin, Azimil Gani Alam, Mohammad Imroz Sohel

Makara Journal of Technology

Energy consumption in buildings is a crucial concern globally, prompting researchers to explore innovative solutions to mitigate its impact. This study investigates the optimization of building envelopes and roof shading systems of existing buildings in Indonesia to realize notable energy savings. Multiple scenarios were explored, with modifications to building envelopes and roof shading, highlighting the overall thermal transfer value as a key parameter. Using EnergyPlus simulations, the efficacy of natural ventilation in corridors and roof shading modifications was assessed in reducing energy consumption. The findings revealed that renovating existing buildings by optimization of the building envelope and roof shading by …

Cobalt Chromium In Biomedical Applications And The Development Of A Pspp Map, Nouralhouda Jamal

Bagley College of Engineering Publications and Scholarship

During the world wars, Cobalt-Chromium (Co-Cr) alloys gained prominence for their use in aircraft engine components, where they exhibited high temperature strength and durability. They are used in a wide range of industries due to their unique set of qualities, particularly strength, corrosion resistance, and biocompatibility. They have emerged as versatile materials with a broad spectrum of applications, from aerospace and automotive components to biomedical implants.

This paper presents a thorough analysis of its composition, processing techniques, microstructure, mechanical properties, and performance characteristics. The primary goal of this project is to develop a PSPP (Process, structure, properties, and performance) map …

Stress Relaxation Cracking In 347h Austenitic Steel Weldments Under Various Heat Treatments: Experiments And Modeling, Yi Yang

Doctoral Dissertations

347H austenitic stainless steel exhibits exceptional creep and corrosion resistance, rendering it an exemplary candidate for pipeline materials, particularly in mid- to high-temperature working conditions. However, due to constraints in component dimensions, welding has been chosen as the preferred method for joining pipeline systems extensively employed in nuclear power plants, fossil fuel plants, and petrochemical companies. The welding process entails the accumulation of residual stress during the cooling stage, along with the introduction of microstructure evolution. Moreover, the residual stress field and microstructure continuously evolve under service conditions, thereby intensifying the susceptibility of crack initiation and propagation. The initial residual …

Temperature Gradient Effect On Solid-Liqid Interface Properties Of Al-Cu Alloy: A Molecular Dynamics Study, Prashant Kumar Jha

All Theses

Aluminum-copper (Al-Cu) alloys are widely used in the aerospace industry due to their favorable strength-to-weight ratio, good fatigue resistance, and corrosion resistance. These properties make Al-Cu alloys an excellent choice for aircraft structural components that require high strength and low weight. Additive manufacturing (AM), also known as 3D printing, has emerged as a promising processing method for Al-Cu alloys in aerospace manufacturing. AM enables the production of lightweight optimized geometries difficult to manufacture through conventional subtractive methods. AM also reduces material waste by only depositing material where needed in the part geometry. The rapid solidification conditions in AM processes motivate …

An Investigation Into The Challenges Of Contemporary Additive Manufacturing: Insights Into The Metallurgical Response Of Materials And Relevant Solution, Huan Ding

LSU Doctoral Dissertations

Additive Manufacturing (AM) has gained attention in recent years due to its unique capabilities in the fabrication of complex parts. As with any new research, there is still a lack of sufficient understanding in the field of additive manufacturing, and further investigation is needed to solve existing problems. Ultimately, the aim is to enable the widespread use of AM components across various industries.

Chapter One provides a brief introduction to the background and current bottlenecks of additive manufacturing technology. Chapter two focuses on the development of high-strength 7075 aluminum alloy (Al7075) for Fused Deposition Modeling and Sintering (FDMS) technology. Al7075 …

Challenges In Optimization For The Performance On Sustainability Dimensions In Reverse Logistics Social Responsibility, Sumarsono Sudarto, Katsuhiko Takahashi, Mochammad Dewo

Makara Journal of Technology

Reverse logistics social responsibility is preferred as the most acceptable solution for addressing the challenges in stakeholders’ debate regarding social responsibility in supply chains because it involves as many actors as possible in the supply chain to perform social responsibility to achieve sustainability. This paper explores the challenges in achieving optimal policies in sustainability dimensions for collection and recycling facilities in reverse logistics. Sustainability dimensions include economic, environmental, and social aspects. The reverse logistics is modeled on System Dynamics, and a simplified statistical analysis using a contour chart is employed in numerical experiments. Results show a narrow area of optimal …

Additive Manufacturing Of High-Performance Nanolamellar Eutectic High-Entropy Alloys, Jie Ren

Doctoral Dissertations

Additive manufacturing, also called three-dimensional (3D) printing, is an emerging technology for printing net-shaped components layer by layer for applications in automotive, aerospace, biomedical and other industries. In addition to the vast design freedom offered by this approach, metal 3D printing via laser powder-bed fusion (L-PBF) involves large temperature gradients and rapid cooling and provides exciting opportunities for producing microstructures and mechanical properties beyond those achievable by conventional processing routes. Although these extreme printing conditions enable microstructural refinement to the nanoscale for achieving high strength. However, high-strength nanostructured alloys by laser additive manufacturing often suffer from limited ductility. Eutectic high-entropy …

Fatigue And Fracture Of Electron Beam Melting Ti-6al-4v, William A. Grell

Electronic Theses and Dissertations

For applications in the aerospace field, selection of materials for a given design requires an understanding of critical properties, like fatigue and fracture, in addition to static mechanical and physical properties. With the ongoing advancements in metallic additive manufacturing techniques and the interest in applying the process to aerospace applications, there is a clear need to fully characterize properties. Arguably, the most attractive alloy for applications in aerospace is the Ti-6Al-4V alloy. The current dissertation examines the mechanical properties of the alloy, made by the Electron Beam Melting (EBM) Powder Bed Fusion (PBF) method. As illustrated in this work, the …

Optimization Of Alti Pld Coating By Increasing Ti Content, N2 And Annealing Which Used For Skd61 Pins In Aluminum Die Casting, Rusman Kosasih, Maria Margaretha Suliyanti Prof, Dedi Priadi, Wisnu Usni

Journal of Materials Exploration and Findings

The Alumunium Titanium Nitrogen (AlTiN) coating is known as one of the best coating materials for protective coating, while Pulsed Laser Deposition (PLD) is a laser coating process used for electric layer and superconductor applications, producing thin films up to 20 µm in thickness. The combination of these two matters has already been researched and is still in progress. One major challenge in the aluminium casting industry is to minimize the damage caused to tool steel pins made from SKD61, when aluminium material sticks to the pin, and halting production. Therefore, research on effective coatings for tool steels and testing …

Mesoscale Modeling And Machine Learning Studies Of Grain Boundary Segregation In Metallic Alloys, Malek Alkayyali

All Dissertations

Nearly all structural and functional materials are polycrystalline alloys; they are composed of differently oriented crystalline grains that are joined at internal interfaces termed grain boundaries (GBs). It is well accepted that GB dynamics play a critical role in many phenomena during materials processing or under operating environments. Of particular interest are GB migration and grain growth processes, as they influence many crystal-size dependent properties, such as mechanical strength and electrical conductivity.

In metallic alloys, GBs offer a plethora of preferential atomic sites for alloying elements to occupy. Indeed, recent experimental studies employing in-situ microscopy revealed strong GB solute segregation …

Point Heat Source Correlation To Microstructural Evolution In Advanced Manufacturing, Mark Anderson

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Although there are different ways that advanced manufacturing can be performed, the use of single-point heat sources has become the standard to control a final product’s properties. It is imperative to understand how the heat source used in the different advanced manufacturing processes affect the microstructure of interest. The intimate relationship between the heat source and microstructure allows for controlling and tailoring a part’s properties. Utilizing different microstructural analysis, the cross-correlation of various point heat sources to developed microstructure was conducted in this dissertation.

Laser powder bed fusion allows for unique print-to-part protocols, but the dynamics of the process makes …

Classification Of Electrical Current Used In Electroplastic Forming, Tyler Grimm

All Dissertations

Electrically assisted manufacturing (EAM) is the direct application of an electric current to a workpiece during manufacturing. This advanced manufacturing process has been shown to produce anomalous effects which extend beyond the current state of modeling of thermal influences. These purported non-thermal effects have collectively been termed electroplastic effects (EPEs).

While there is a distinct difference in results between steady-state (ideal DC) testing and pulsed current testing, the very definition of these two EAM methods has not been well established. A "long" pulse may be considered DC current; a "short" pulse may produce electroplastic effects; and even "steady-state" current shapes …

Effects Of Tempering Temperature On Gas Turbine Fan Cases, Seth Utter

Honors Scholar Theses

The project aimed to investigate the effects of tempering temperature on metals used for gas turbine engine fan cases as a major relevant concern is containing blades in during blade-out events. There are three ways to accomplish this: using a thicker metal, incorporating different materials into the case, or heat treating the metal. This project focused on the third solution: reviewing the impact toughness and hardness of fractured samples and their equivalent ductile-to-brittle transition shear faces. Given its availability, 1045 steel, as opposed to aerospace grade metals, was used for in-house testing. The data obtained from these experiments were then …

Mechanical Characterization Of Additively Manufactured Alloys Compared To Their Wrought Counterparts, Laith A. Alqawasmi

Mechanical Engineering ETDs

Additive manufacturing is a method of manufacturing based on building parts layer by layer, allowing for more control over shape of the product, therefore reducing machining costs, reducing material waste, faster production times and the ability to build complex engineering design that other manufacturing technologies won’t be able to produce. This research is on the tensile and indentation testing (following ASME standards) of 3D printed Ti-6Al-4V and Inconel 718 built by powder-based direct energy deposition technology. Ti-6Al-4V is an attractive material for the aerospace and aviation industry, and Inconel 718, a nickel-chromium based superalloy, is an attractive material for usage …

Effect Of Austenization And Repeated Quenching On The Microstructures And Mechanical Properties Of Wear-Resistant Steel, Yanuar Nugraha, Myrna Ariati Mochtar

Journal of Materials Exploration and Findings

This study was focused on determining the effect of repeated austenitization and quenching on mechanical properties and microstructure. The experiment was carried out in a rolled quencher facility with a heat treatment process of one to two times, with parameters of an austenizing temperature of 9500C and quenching at a temperature of 8500C with pressurized water media. Testing of specimens, including microstructure observations and hardness testing. The repeated heat treatment process showed an increase in hardness of 0.79% on one-time repeated heat treatment and 1.65% on two repeated heat treatments. This occurs due to the presence accompanied by refinement of …

Performance Evaluation Of Composite Sandwich Structures With Additively Manufactured Aluminum Honeycomb Cores With Increased Bonding Surface Area, M. Rangapuram, S. K. Dasari, Joseph William Newkirk, K. Chandrashekhara, H. Misak, P. R. Toivonen, D. Klenosky, T. Unruh, J. Sam

Materials Science and Engineering Faculty Research & Creative Works

Modern aerostructures, including wings and fuselages, increasingly feature sandwich structures due to their high-energy absorption, low weight, and high flexural stiffness. The face sheet of these sandwich structures are typically thin composite laminates with interior honeycombs made of Nomex or aluminum. Standard cores are structurally efficient, but their design cannot be varied throughout the structure. With additive manufacturing (AM) technology, these core geometries can be altered to meet the design requirements that are not met in standard honeycomb cores. This study used a modified aluminum honeycomb core, with increased surface area on the top and bottom, as the core material …

Investigation Of Oxidation And Corrosion Resistance Of Ni-Based Alloys And Stainless Steels Under Co2 Environments At Elevated Temperatures, Spencer Roy Fultineer

Graduate Theses, Dissertations, and Problem Reports

High mechanical strength integrity, high robustness towards oxidation, and high resistance to carburization under CO2 environments at elevated temperatures are usually required for metallic systems that are employed for power generation. INCONEL 625 is a nickel-based superalloy that started development in the 1950s. This material was designed with the distinct purpose of use in high-temperature and high-pressure systems. While various materials possess the physical properties to handle these conditions, the creation of IN625 addresses the need for a material to withstand the highly corrosive properties of these kinds of environments. In order to evaluate the oxidation and corrosion resistance of …

Investigation Of Microstructurally Dependent Mechanical Properties Of Cold Sprayed Copper Using Correlative Microscopy, Quintin Otto

UNF Graduate Theses and Dissertations

This project employs multi-instrument materials characterization to analyze material made with the “Cold Spray” additive manufacturing process. Cold spray is an emerging additive manufacturing technique with unique benefits resulting from its low temperature adhesion process induced by plastic deformation. Metallic powder collides at high speeds creating three dimensional materials and coatings without the need for melting. Copper cold sprayed specimens were analyzed using a series of imaging techniques to characterize the microstructure at varying levels of detail and magnification. Scanning electron microscopy and electron back scattered diffraction were paired with microhardness testing to generate a correlative comparison between microstructure and …

Damage Stability Study Of A 500 Dw Ro-Ro Ferry Vessel, Zulfaidah Ariany, Budhi Santoso, Sarwoko Sarwoko, Nauval Abdurrahman Prasetyo

Makara Journal of Technology

The development of the crossing transportation industry is currently increasing in the island areas. The use of Ro-Ro type ferry boats is extremely efficient in moving people, goods, and vehicles. The current research focuses on the damage stability of the 500 DWT Ro-Ro ferry, which aims to meet the needs of the Ro-Ro ferry in the archipelago area. The previously existing initial design of a barge hull with a main size Lpp = 40.15 m, B = 12 m, H = 3.2 m, and T = 2.15 m was used to analyze the damage stability condition further. First, the drawings …

Structural Risk-Based Underwater Inspection (Rbui) As A Cost Reduction Of Field’S End Of Production Life, Ivan Fitrian Putra, Johny Wahyuadi Soedarsono, Mirza Mahendra, Yuki Haidir, Faisal Dwiyana Purnawarman, Iwan Sukirna, Widi Hernowo

Journal of Materials Exploration and Findings

Mubadala Petroleum operates offshore platforms in a southern Makassar Straits that needs to be periodically inspected. The cost for the inspection is massive due to the high cost of mobilization and demobilization of vessels including crew and equipment. In response of a new approach to reduce cost, a Risk-Based Underwater Inspection (RBUI) methodology is developed. This RBUI purpose is to reduce the inspection interval of the offshore platform, from every 2 years to a longer period^[1]. There are existing RBUI methodologies, which are already developed and implemented in other companies^[5]. Purpose of this paper is to …

A Constitutive Material Model For Simulating Texture Evolution And Anisotropy Effects In Cold Spray., Creston Michael Giles

Theses and Dissertations

Cold spray has seen rapid advancement since its inception and has shown significant potential as a method of additive manufacturing. However, the large plastic deformation and repeated heating/cooling cycles that the material undergoes during the cold spray process can result in gradients in material structure and large residual stresses. The purpose of this study is to extend the existing EMMI material model to include anisotropic material response through the use of orientation distribution functions to predict residual stresses and anisotropy resulting from cold spray and similar additive manufacturing processes. Through the use of a finite element simulation, yield surfaces for …

Platinum-Iridium Alloys In Jewelry, Nathen C. Christa, Seth Walker, Dylan Hallman

ME 4133/6133 Mechanical Metallurgy

One of the most widely used metals on the periodic table is Platinum (Pt). The name is derived from the Spanish Platina, meaning “silver.” This malleable, ductile material is widely used in applications due to its unique chemical properties. A couple of these unique properties include a high melting point and good resistance to corrosion or chemical attack. Platinum materials have alloys that are indispensable in the chemical laboratory for electrodes. This allows for material applications in crucibles and dishes to withstand elevated temperatures. Platinum is used primarily in catalytic converters in vehicles converting emissions from the vehicle’s engine into …

High-Carbon Steel In Additive Manufacturing, Chidi N. Agusiegbe, Devin Morton, Emmanuel Moore

ME 4133/6133 Mechanical Metallurgy

High-carbon steel can be processed through numerous methods. The method that will be focused on primarily is processing high-carbon steel through means of additive manufacturing. Additive manufacturing is the industrial production name for 3D printing, a computer-controlled process that creates three-dimensional objects by depositing materials, usually in layers. AM methods like wire laser additive manufacturing (WLAM) and electron beam melting (EBM) are all common methods for fabricating high carbon steel. The perks associated with these methods are that they improve some drawbacks of the natural properties of high-carbon steel. This paper discusses the uses of these additive manufacturing methods along …

High Carbon Steel In Additive Manufacturing, Emmanuel Moore Ii, Devin Morton, Chid Agusiegbe

ME 4133/6133 Mechanical Metallurgy

The first known use of carbon steel dates back to 500 A.D. when a blacksmith mistakenly used iron ore as a primary material for smithing. This material, as the name suggests, is made up of both carbon and iron. This material, as one of the most abundant at the time, was used most frequently in European and Asian countries. “Carbon steel first appeared around the year 500 AD in Damascus steel swords as well as Japanese swords. They were prized for their sharp edges and sturdiness compared to other weapons of the era. The composition of these swords was very …

Integration Of Hadfield Steel Into Modern Body Armor, Jason T. Fridlund

ME 4133/6133 Mechanical Metallurgy

The increased lethality of recently fielded projectiles mandates a proportional escalation in armor performance. Recent advancements in ceramic technologies have allowed designers to incorporate harder but more brittle materials into hard armor designs to defeat yet more capable penetrating projectiles. Ceramics suffer from the feature of shattering, however, even when impacted by threats below their design parameters. While this shattering mechanism is used effectively to dissipate energy from high-energy rifle projectiles, it is wasted on low-energy projectiles, and can result in easily damaged lifesaving gear, both of which are undesirable in combat. In contrast, steel body armor has been used …

High Carbon Steel In Additive Manufacturing, Chidi Agusiegbe, Devin Morton, Emmanuel Moore

ME 4133/6133 Mechanical Metallurgy

Infographic demonstrating the composition, and use of high carbon steels as well as the process of the material in additive manufacturing.

Sae 8620 Pspp Map - Infographic, John F. Mitchener

ME 4133/6133 Mechanical Metallurgy

This infographic summarizes a Processing-Structure-Property-Performance (PSPP) Map for SAE 8620 alloy steel, with an emphasis on the gas carburization process. This PSPP map allows researchers and material scientists to better understand the processes that drive the microstructures, material properties, and ultimate performance parameters.

Characterization Of Materials Properties In Additively Manufactured Aisi-420 Martensitic Steel Deposited By Laser Engineered Net Shaping, Md Mehadi Hassan

Nanoscience and Microsystems ETDs

Metal additive manufacturing (AM) is a disruptive technology enabling the fabrication of complex and near-net-shaped parts by adding material layer-wise. It offers reduced lead production time. AM processes are finding applications in many industrial sectors such as aerospace, automotive, biomedical, and mold tooling. Despite the tremendous advantages of AM, some challenges still prevent this technology's adoption in high-standard applications. Anisotropy and inhomogeneity in the mechanical properties of the as-built parts and the existence of pores and lack-of-fusion defects are considered the main issues in directed energy deposition (L-DED) parts. Laser-engineered net shaping LENS® offers excellent possibilities to fabricate metal tools …