Open Access. Powered by Scholars. Published by Universities.®
- Keyword
-
- Aerospace engineering (1)
- Carbon (1)
- Cloth (1)
- Co-Bond (1)
- Co-Cure (1)
-
- Composite structures (1)
- Debris (1)
- Dynamic response (1)
- Electromagnetic (1)
- Fracture (1)
- Gun (1)
- Harness-Satin (1)
- Hypersonic (1)
- Modal analysis (1)
- Mode I (1)
- Nondestructive inspection/evaluation (NDI/E) (1)
- Orbital (1)
- Post-Bond (1)
- Rail (1)
- Random Vibration CubeSat P-POD Dynamic Environment Isolation (1)
- Structural analysis (1)
- Structural health monitoring (SHM) (1)
Articles 1 - 4 of 4
Full-Text Articles in Mechanical Engineering
Mode I Fracture Toughness Of Eight-Harness-Satin Carbon Cloth Weaves For Co-Cured And Post-Bonded Laminates, Josh E. Smith
Mode I Fracture Toughness Of Eight-Harness-Satin Carbon Cloth Weaves For Co-Cured And Post-Bonded Laminates, Josh E. Smith
Master's Theses
Mode I interlaminar fracture of 3k 8-Harness-Satin Carbon cloth, with identical fill and weft yarns, pre-impregnated with Newport 307 resin was investigated through the DCB test (ASTM D5528). Crack propagations along both the fill and weft yarns were considered for both post-bonded (co-bonded) and co-cured laminates. A patent-pending delamination insertion method was compared to the standard Teflon film option to assess its applicability to mode I fracture testing. The Modified Beam Theory, Compliance Calibration method, and Modified Compliance Calibration method were used for comparative purposes for these investigations and to evaluate the validity of the proposed Equivalent Stiffness (EQS) method. …
Design, Fabrication, And Testing Of An Emr Based Orbital Debris Impact Testing Platform, Jeffrey J. Maniglia Jr.
Design, Fabrication, And Testing Of An Emr Based Orbital Debris Impact Testing Platform, Jeffrey J. Maniglia Jr.
Master's Theses
This paper describes the changes made from Cal Poly’s initial railgun system, the Mk. 1 railgun, to the Mk. 1.1 system, as well as the design, fabrication, and testing of a newer and larger Mk. 2 railgun system. The Mk. 1.1 system is developed as a more efficient alteration of the original Mk. 1 system, but is found to be defective due to hardware deficiencies and failure, as well as unforeseen efficiency losses. A Mk. 2 system is developed and built around donated hardware from the Naval Postgraduate School. The Mk. 2 system strove to implement an efficient, augmented, electromagnetic …
Analysis And Mitigation Of The Cubesat Dynamic Environment, Steve M. Furger
Analysis And Mitigation Of The Cubesat Dynamic Environment, Steve M. Furger
Master's Theses
A vibration model was developed for CubeSats inside the Poly-Picosatellite Orbital Deployer (P-POD). CubeSats are fixed in the Z axis of deployers, and therefore resonate with deployer peaks. CubeSats generally start fixed in the X and Y axes, and then settle into an isolated position. CubeSats do not resonate with deployers after settling into an isolated position. Experimental data shows that the P-POD amplifies vibration loads when CubeSats are fixed in the deployer, and vibration loads are reduced when the CubeSats settle into an isolated position. A concept for a future deployer was proposed that isolates CubeSats from the deployer …
The Effect Of Sensor Mass, Sensor Location, And Delamination Location Of Different Composite Structures Under Dynamic Loading, Albert Darien Liu
The Effect Of Sensor Mass, Sensor Location, And Delamination Location Of Different Composite Structures Under Dynamic Loading, Albert Darien Liu
Master's Theses
This study investigated the effect of sensor mass, sensor location, and delamination location of different composite structures under dynamic loading. The study pertains to research of the use of accelerometers and dynamic response as a cost-effective and reliable method of structural health monitoring in composite structures. The composite structures in this research included carbon fiber plates, carbon fiber-foam sandwich panels, and carbon-fiber honeycomb sandwich panels. The composite structures were manufactured with the use of a Tetrahedron MTP-8 heat press. All work was conducted in the Cal Poly Aerospace Structures/Composites Laboratory. Initial delaminations were placed at several locations along the specimen, …