Mechanical Engineering Commons^™

Developing A Miniature Smart Boat For Marine Research, Michael Isaac Eirinberg

Computer Engineering

This project examines the development of a smart boat which could serve as a possible marine research apparatus. The smart boat consists of a miniature vessel containing a low-cost microcontroller to live stream a camera feed, GPS telemetry, and compass data through its own WiFi access point. The smart boat also has the potential for autonomous navigation. My project captivated the interest of several members of California Polytechnic State University, San Luis Obispo’s (Cal Poly SLO) Marine Science Department faculty, who proposed a variety of fascinating and valuable smart boat applications.

Design And Control Of Next-Generation Uavs For Effectively Interacting With Environments, Caiwu Ding

Dissertations

In this dissertation, the design and control of a novel multirotor for aerial manipulation is studied, with the aim of endowing the aerial vehicle with more degrees of freedom of motion and stability when interacting with the environments. Firstly, it presents an energy-efficient adaptive robust tracking control method for a class of fully actuated, thrust vectoring unmanned aerial vehicles (UAVs) with parametric uncertainties including unknown moment of inertia, mass and center of mass, which would occur in aerial maneuvering and manipulation. The effectiveness of this method is demonstrated through simulation. Secondly, a humanoid robot arm is adopted to serve as …

Cloudbots: Autonomous Atmospheric Explorers, Akash Binoj

Honors Scholar Theses

The CloudBot is an autonomous weather balloon that operates on the principle of variable buoyancy to ascend and descend in the atmosphere. This project aims to develop a device that will collect atmospheric measurements and communicate them mid-flight. The apparatus consists of a helium-filled balloon, the robotic payload, and an air cell. The fixed-volume helium balloon at the top provides an upwards buoyancy force, while the air cell at the bottom can hold a variable amount of pressure to adjust the weight of the CloudBot. By doing so, it is able to travel in storm conditions and collect valuable atmospheric …

Model Based Force Estimation And Stiffness Control For Continuum Robots, Vincent A. Aloi

Doctoral Dissertations

Continuum Robots are bio-inspired structures that mimic the motion of snakes, elephant trunks, octopus tentacles, etc. With good design, these robots can be naturally compliant and miniaturizable, which makes Continuum Robots ideal for traversing narrow complex environments. Their flexible design, however, prevents us from using traditional methods for controlling and estimating loading on rigid link robots.

In the first thrust of this research, we provided a novel stiffness control law that alters the behavior of an end effector during contact. This controller is applicable to any continuum robot where a method for sensing or estimating tip forces and pose exists. …

A Low-Cost And Low-Tech Solution To Test For Variations Between Multiple Offline Programming Software Packages., Steffen Wendell Bolz

Masters Theses & Specialist Projects

This research paper chronicles the attempt to bring forth a low-cost and low-tech testing methodology whereby multiple offline programming (OLP) software packages’ generated programs may be compared when run on industrial robots. This research was initiated by the discovery that no real research exists to test between iterations of OLP software packages and that most research for positional accuracy and/or repeatability on industrial robots is expensive and technologically intensive. Despite this, many countries’ leaders are pushing for intensive digitalization of manufacturing and Small and Mediumsized Enterprises (SMEs) are noted to be lagging in adoption of such technologies. The research consisted …

Can We Make Our Robot Play Soccer? Influence Of Collaborating With Preservice Teachers And Fifth Graders On Undergraduate Engineering Students' Learning During A Robotic Design Process (Work In Progress), Krishnanand Kaipa, Jennifer Kidd, Julia Noginova, Francisco Cima, Stacie Ringleb, Orlando Ayala, Pilar Pazos, Kristie Gutierrez, Min Jung Lee

Mechanical & Aerospace Engineering Faculty Publications

This work-in-progress paper describes engineering students’ experiences in an NSF-funded project that partnered undergraduate engineering students with pre-service teachers to plan and deliver robotics lessons to fifth graders at a local school. This project aims to address an apparent gap between what is taught in academia and industry’s expectations of engineers to integrate perspectives from outside their field to solve modern societal problems requiring a multidisciplinary approach. Working in small teams over Zoom, participating engineering, education, and fifth grade students designed, built, and coded bio-inspired COVID companion robots. The goal for the engineering students was to build new interprofessional skills, …