Mechanical Engineering Commons^™

Modeling, Control And Estimation Of Reconfigurable Cable Driven Parallel Robots, Adhiti Raman Thothathri

All Dissertations

The motivation for this thesis was to develop a cable-driven parallel robot (CDPR) as part of a two-part robotic device for concrete 3D printing. This research addresses specific research questions in this domain, chiefly, to present advantages offered by the addition of kinematic redundancies to CDPRs. Due to the natural actuation redundancy present in a fully constrained CDPR, the addition of internal mobility offers complex challenges in modeling and control that are not often encountered in literature.

This work presents a systematic analysis of modeling such kinematic redundancies through the application of reciprocal screw theory (RST) and Lie algebra while …

Material Characterization And Comparison Of Sol-Gel Deposited And Rf Magnetron Deposited Lead Zirconate Titanate Thin Films, Katherine Lynne Miles

Mechanical Engineering ETDs

Lead zirconate titanate (PZT) has been a material of interest for sensor, actuator, and transducer applications in microelectromechanical systems (MEMS). This is due to their favorable piezoelectric, pyroelectric and ferroelectric properties. While various methods are available to deposit PZT thin films, radio frequency (RF) magnetron sputtering was selected to provide high quality PZT films with the added capability of batch processing. These sputter deposited PZT films were characterized to determine their internal film stress, Young’s modulus, composition, and structure. After characterization, the sputtered PZT samples were poled using corona poling and direct poling methods. As a means of comparison, commercially …

A Machine Learning Approach To Robotic Additive Manufacturing Of Uv-Curable Polymers Using Direct Ink Writing, Luis A. Velazquez

LSU Master's Theses

This thesis presents the design and implementation of a robotic additive manufacturing system that uses ultraviolet (UV)-curable thermoset polymers. Its design considers future applications involving free-standing 3D printing by means of partial UV curing and the fabrication of samples that are reinforced with fillers or fibers to manufacture complex-shape objects.

The proposed setup integrates a custom-built extruder with a UR5e collaborative manipulator. The capabilities of the system were demonstrated using Anycubic resin formulations containing fumed silica (FS) at varying weight fractions from 2.8 to 8 wt%. To fully cure the specimens after fabrication, a UV chamber was used. Then, measurements …

Multi-Robot Symbolic Task And Motion Planning Leveraging Human Trust Models: Theory And Applications, Huanfei Zheng

All Dissertations

Multi-robot systems (MRS) can accomplish more complex tasks with two or more robots and have produced a broad set of applications. The presence of a human operator in an MRS can guarantee the safety of the task performing, but the human operators can be subject to heavier stress and cognitive workload in collaboration with the MRS than the single robot. It is significant for the MRS to have the provable correct task and motion planning solution for a complex task. That can reduce the human workload during supervising the task and improve the reliability of human-MRS collaboration. This dissertation relies …

Collaborative Robotics Strategies For Handling Non-Repetitive Micro-Drilling Tasks Characterized By Low Structural Mechanical Impedance, Xiangyu Wang

Mechanical & Aerospace Engineering Theses & Dissertations

Mechanical micro-drilling finds widespread use in diverse applications ranging from advanced manufacturing to medical surgery. This dissertation aims to develop techniques that allow programming of robots to perform effective micro-drilling tasks. Accomplishing this goal is faced with several challenges. Micro-drills suffer from frequent breakage caused from variations in drill process parameters. Micro-drilling tasks afford extremely low feed rates and almost zero tolerance for any feed rate variations. The accompanying robot programming task is made difficult as mathematical models that capture the micro-drilling process complexities and sensitive variations in micro-drill parameters are highly difficult to obtain. Therefore, an experimental approach is …

Developing A Miniature Smart Boat For Marine Research, Michael Isaac Eirinberg

Computer Engineering

This project examines the development of a smart boat which could serve as a possible marine research apparatus. The smart boat consists of a miniature vessel containing a low-cost microcontroller to live stream a camera feed, GPS telemetry, and compass data through its own WiFi access point. The smart boat also has the potential for autonomous navigation. My project captivated the interest of several members of California Polytechnic State University, San Luis Obispo’s (Cal Poly SLO) Marine Science Department faculty, who proposed a variety of fascinating and valuable smart boat applications.

Therapeutic Mechanical Horse, Cade M. Liberty, Aleya Dolorfino, Peter Philips, Zuzanna Dominik, Luke Watts

Mechanical Engineering

Jack's Helping Hand and its hippotherapy participants required a device to serve as an alternative to a live horseback riding experience that could also increase the range of riders. This would provide more clients with equine-assisted therapy that has proven to better the lives of people with both physical and mental disabilities. Horses can be unpredictable, tall, and sometimes anxiety-inducing, especially for new riders. Our group’s aim was to develop a mechanical horse that will be able to reduce these issues for equine therapy centers and the riders they help. When a rider gets to practice sitting on the horse …

Design And Control Of Next-Generation Uavs For Effectively Interacting With Environments, Caiwu Ding

Dissertations

In this dissertation, the design and control of a novel multirotor for aerial manipulation is studied, with the aim of endowing the aerial vehicle with more degrees of freedom of motion and stability when interacting with the environments. Firstly, it presents an energy-efficient adaptive robust tracking control method for a class of fully actuated, thrust vectoring unmanned aerial vehicles (UAVs) with parametric uncertainties including unknown moment of inertia, mass and center of mass, which would occur in aerial maneuvering and manipulation. The effectiveness of this method is demonstrated through simulation. Secondly, a humanoid robot arm is adopted to serve as …

Model Based Force Estimation And Stiffness Control For Continuum Robots, Vincent A. Aloi

Doctoral Dissertations

Continuum Robots are bio-inspired structures that mimic the motion of snakes, elephant trunks, octopus tentacles, etc. With good design, these robots can be naturally compliant and miniaturizable, which makes Continuum Robots ideal for traversing narrow complex environments. Their flexible design, however, prevents us from using traditional methods for controlling and estimating loading on rigid link robots.

In the first thrust of this research, we provided a novel stiffness control law that alters the behavior of an end effector during contact. This controller is applicable to any continuum robot where a method for sensing or estimating tip forces and pose exists. …

Control, Decision-Making, And Learning Approaches For Connected And Autonomous Driving Systems With Humans-In-The-Loop, Fangjian Li

All Dissertations

By virtue of vehicular connectivity and automation, the vehicle becomes increasingly intelligent and self-driving capable. However, no matter what automation level the vehicle can achieve, humans will still be in the loop despite their roles. First, considering the manual driving car as a disturbance to the connected and autonomous vehicles (CAVs), a novel string stability is proposed for mixed traffic platoons consisting of both autonomous and manual driving cars to guarantee acceptable motion fluctuation and platoon safety. Furthermore, humans are naturally considered as the rider in the passenger vehicle. A human-centered cooperative adaptive cruise control (CACC) is designed to improve …

Formation Control With Bounded Controls And Collision Avoidance: Theory And Application To Quadrotor Unmanned Air Vehicles, Zachary S. Lippay

Theses and Dissertations--Mechanical Engineering

This dissertation presents new results on multi-agent formation control and applies the new control algorithms to quadrotor unmanned air vehicles. First, this dissertation presents a formation control algorithm for double-integrator agents, where the formation is time varying and the agents’ controls satisfy a priori bounds (e.g., the controls accommodate actuator saturation). The main analytic results provide sufficient conditions such that all agents converge to the desired time-varying relative positions with one another and the leader, and have a priori bounded controls (if applicable). We also present results from rotorcraft experiments that demonstrate the algorithm with time-varying formations and bounded controls. …

An Experimental Study Towards Underwater Propulsion System Using Structure Borne Traveling Waves, Shreyas Suhas Gadekar

Dissertations, Master's Theses and Master's Reports

The method of generating steady-state structure-borne traveling waves underwater in an infinite media creates abundant opportunities in the field of propulsive applications, and they are gaining attention from several researchers. This experimental study provides a framework for harnessing traveling waves in a 1D beam immersed under quiescent water using two force input methods and providing a motion to an object floating on the surface of the water.

In this study, underwater traveling waves are tailored using structural vibrations at five different frequencies in the range of 10Hz to 300Hz. The resulting fluid motion provides a propulsive thrust that moves a …

Design And Control Of Quasi-Direct Drive Actuation For Lightweight And Versatile Wearable Robots, Shuangyue Yu

Dissertations and Theses

Wearable robots have shown great potential for augmenting the physical capabilities of humans in lab settings. However, wearable robots for augmenting the physical capabilities of humans under community-based conditions are the new frontier of robotics. Furthermore, the design and control are still considered to be grand challenges for providing physical augmentation for humans. In terms of design, the state-of-the-art exoskeletons are typically rigid, bulky, and limited to lab settings. In terms of control, most of the rhythmic controllers are not versatile and are focused only on steady-state walking assistance.

The motivation behind my research is to improve both the design …