Open Access. Powered by Scholars. Published by Universities.®

Mechanical Engineering Commons

Open Access. Powered by Scholars. Published by Universities.®

Articles 1 - 20 of 20

Full-Text Articles in Mechanical Engineering

Data Driven Low-Bandwidth Intelligent Control Of A Jet Engine Combustor, Nathan L. Toner Aug 2016

Data Driven Low-Bandwidth Intelligent Control Of A Jet Engine Combustor, Nathan L. Toner

Open Access Dissertations

This thesis introduces a low-bandwidth control architecture for navigating the input space of an un-modeled combustor system between desired operating conditions while avoiding regions of instability and blow-out. An experimental procedure is discussed for identifying regions of instability and gathering sufficient data to build a data-driven model of the system's operating modes. Regions of instability and blow-out are identified experimentally and a data-driven operating point classifier is designed. This classifier acts as a map of the operating space of the combustor, indicating regions in which the flame is in a "good" or "bad" operating mode. A data-driven predictor is also …


Implementing And Testing A Panel-Based Method For Modeling Acoustic Scattering From Cfd Input, S. Hales Swift Aug 2016

Implementing And Testing A Panel-Based Method For Modeling Acoustic Scattering From Cfd Input, S. Hales Swift

Open Access Dissertations

Exposure of sailors to high levels of noise in the aircraft carrier deck environment is a problem that has serious human and economic consequences. A variety of approaches to quieting exhausting jets from high-performance aircraft are undergoing development. However, testing of noise abatement solutions at full-scale may be prohibitively costly when many possible nozzle treatments are under consideration. A relatively efficient and accurate means of predicting the noise levels resulting from engine-quieting technologies at personnel locations is needed. This is complicated by the need to model both the direct and the scattered sound field in order to determine the resultant …


Particle Modeling Of Non-Equilibrium Field Emission Driven Rf Microplasmas, Siva Sashank Tholeti Aug 2016

Particle Modeling Of Non-Equilibrium Field Emission Driven Rf Microplasmas, Siva Sashank Tholeti

Open Access Dissertations

Non-equilibrium microplasmas at atmospheric pressures have been investigated for active flow control, micropropulsion and electronic display applications to name a few. The operational voltages for these microplasmas are on the order of kilovolts. When the electric field at the electrodes reaches GV/m or tens of GV/m either due to reduced interelectrode spacing and surface irregularities or due to carefully designed nanostructures on the electrodes, quantum processes such as field emission and field ionization come into effect. These can potentially reduce the operational voltages of microplasma devices by an order of magnitude. Due to the rarefied and non-equilibrium nature of these …


Experimental Investigation And Numerical Simulation Of A Copper Micro-Channel Heat Exchanger With Hfe-7200 Working Fluid, Eric Borquist Jul 2016

Experimental Investigation And Numerical Simulation Of A Copper Micro-Channel Heat Exchanger With Hfe-7200 Working Fluid, Eric Borquist

Doctoral Dissertations

Ever increasing cost and consumption of global energy resources has inspired the development of energy harvesting techniques which increase system efficiency, sustainability, and environmental impact by using waste energy otherwise lost to the surroundings. As part of a larger effort to produce a multi-energy source prototype, this study focused on the fabrication and testing of a waste heat recovery micro-channel heat exchanger. Reducing cost and facility requirements were a priority for potential industry and commercial adoption of such energy harvesting devices. During development of the micro-channel heat exchanger, a new fabrication process using mature technologies was created that reduced cost, …


Experimental Verification And Integration Of A Next Generation Smart Power Management System, Tavis Clemmer May 2015

Experimental Verification And Integration Of A Next Generation Smart Power Management System, Tavis Clemmer

Graduate Theses and Dissertations

With the increase in energy demand by the residential community in this country and the diminishing fossil fuel resources being used for electric energy production there is a need for a system to efficiently manage power within a residence. The Smart Green Power Node (SGPN) is a next generation energy management system that automates on-site energy production, storage, consumption, and grid usage to yield the most savings for both the utility and the consumer. Such a system automatically manages on-site distributed generation sources such as a PhotoVoltaic (PV) input and battery storage to curtail grid energy usage when the price …


Dropwise Condensation Dynamics In Humid Air, Julian Eduardo Castillo Chaco Oct 2014

Dropwise Condensation Dynamics In Humid Air, Julian Eduardo Castillo Chaco

Open Access Theses

Dropwise condensation of atmospheric water vapor is important in multiple practical engineering applications. The roles of environmental factors and surface morphology/chemistry on the condensation dynamics need to be better understood to enable efficient water-harvesting, dehumidication, and other psychrometric processes. Systems and surfaces that promote faster condensation rates and self-shedding of condensate droplets could lead to improved mass transfer rates and higher water yields in harvesting applications. The thesis presents the design and construction of an experimental facility that allows visualization of the condensation process as a function of relative humidity. Dropwise condensation experiments are performed on a vertically oriented, hydrophobic …


Waste Heat Recovery Options In A Large Gas-Turbine Combined Power Plant, Ularee Upathumchard Oct 2014

Waste Heat Recovery Options In A Large Gas-Turbine Combined Power Plant, Ularee Upathumchard

Open Access Theses

This study focuses on power plant heat loss and how to utilize the waste heat in energy recovery systems in order to increase the overall power plant efficiency. The case study of this research is a 700-MW natural gas combined cycle power plant, located in a suburban area of Thailand. An analysis of the heat loss of the combustion process, power generation process, lubrication system, and cooling system has been conducted to evaluate waste heat recovery options. The design of the waste heat recovery options depends to the amount of heat loss from each system and its temperature. Feasible waste …


High Voltage Rear Electric Drivetrain Design For A Parallelthrough-The-Road Plug-In Hybrid Electric Vehicle, Adam Garrett Fogarty Oct 2014

High Voltage Rear Electric Drivetrain Design For A Parallelthrough-The-Road Plug-In Hybrid Electric Vehicle, Adam Garrett Fogarty

Open Access Theses

Purdue University was selected as one of 15 universities to participate in a three year Advanced Vehicle Technology Competition (AVTC) called EcoCar2: Plugging Into the Future. The vehicle built by the Purdue team was a Parallel-Through-The-Road Plug-in Hybrid Electric Vehicle (PTTR PHEV). The vehicle utilized a B20 diesel powertrain to power the front wheels, as well as a custom electric drivetrain to power the rear wheels. Using this vehicle during the final year of the competition, the team was successful in placing 4th overall as well as 2nd in the category of Well-To-Wheel (WTW) Greenhouse Gas Emissions. A stock 2013 …


Indoor Acoustic Mapping And Geolocation, Thomas Shyy Oct 2014

Indoor Acoustic Mapping And Geolocation, Thomas Shyy

Open Access Theses

The Global Positioning System (GPS) is widely used in navigations of flights, vehicles and travelers nowadays. However, the signals are not always available and there are some cases where the receptions of the GPS signal can be lost because of the presence of urban canyons, buildings, tunnels and forests. Another down side for the GPS is that indoor positioning can be really difficult because of the greater signal interference from the indoor.

On the other hand, the concept of echolocation has also been used for positioning purposes. Echolocation offers a promising approach to improve the quality of life of people …


A Novel Microgrid Demand-Side Management System For Manufacturing Facilities, Terance Jerome Harper Jul 2014

A Novel Microgrid Demand-Side Management System For Manufacturing Facilities, Terance Jerome Harper

Open Access Theses

Thirty-one percent of annual energy consumption in the United States occurs within the industrial sector, where manufacturing processes account for the largest amount of energy consumption and carbon emissions. For this reason, energy efficiency in manufacturing facilities is increasingly important for reducing operating costs and improving profits. Using microgrids to generate local sustainable power should reduce energy consumption from the main utility grid along with energy costs and carbon emissions. Also, microgrids have the potential to serve as reliable energy generators in international locations where the utility grid is often unstable.

For this research, a manufacturing process that had approximately …


High Temperature Flooded Expansion For Solar Thermal Power Generation, Nelson Alexander James Jul 2014

High Temperature Flooded Expansion For Solar Thermal Power Generation, Nelson Alexander James

Open Access Theses

Even though solar power usage has seen rapid growth over the past decade, fossil fuel generation sources are still generally a less expensive means of producing power. The Liquid-Flooded Ericsson Cycle (LFEC) was investigated as a high efficiency power cycle for reducing the cost of concentrated solar power (CSP) plants and helping to address this cost disparity. High temperature flooded expansion was identified as one of the main challenges in regards to utilizing the LFEC as a power cycle. Thermodynamic models were developed to help assess the performance of the LFEC and a load stand was constructed to test a …


Improving Indoor Air Quality Through Botanical Air Filtration In Energy Efficient Residences, Daniel William Newkirk Apr 2014

Improving Indoor Air Quality Through Botanical Air Filtration In Energy Efficient Residences, Daniel William Newkirk

Open Access Theses

According to the U.S. EPA, the average American spends 90% of their time indoors where pollutants are two to five times more prevalent than outside. The consequences of these pollutants are estimated to cost the U.S. 125 billion dollars in lost health and productivity. Background literature suggests botanical air filtration may be able to solve this problem by leveraging the natural ability of plants to purify indoor air. By improving indoor air quality, energy consumption can also be reduced by bringing in less outside air to dilute contaminants within the space. A botanical air filter, called the Biowall, was designed …


The Influence Of Non-Equilibrium Pressure On Rotating Flows, Irfan Rashid Zardadkhan Jul 2012

The Influence Of Non-Equilibrium Pressure On Rotating Flows, Irfan Rashid Zardadkhan

Mechanical & Aerospace Engineering Theses & Dissertations

This study was undertaken to investigate the influence of pressure relaxation on steady, incompressible flows with strong streamline curvature. In the early part of this dissertation research, the significance of non-equilibrium pressure forces in controlling the structure of a steady, two dimensional axial vortex was demonstrated. In order to extend the study of pressure relaxation influences on more complex rotating flows, this dissertation has examined other rotating flow features that can be associated with hurricanes, tornadoes and dust devils. To model these flows, modified boundary layer equations were developed for a fluid column rotating near a solid plane including the …


Design Of Orbital Maneuvers With Aeroassisted Cubesatellites, Stephanie Clark May 2012

Design Of Orbital Maneuvers With Aeroassisted Cubesatellites, Stephanie Clark

Graduate Theses and Dissertations

Recent advances within the field of cube satellite technology has allowed for the possible development of a maneuver that utilizes a satellite's Low Earth Orbit (LEO) and increased atmospheric density to effectively use lift and drag to implement a noncoplanar orbital maneuver. Noncoplanar maneuvers typically require large quantities of propellant due to the large delta-v that is required. However, similar maneuvers using perturbing forces require little or no propellant to create the delta-v required. This research reported here studied on the effects of lift on orbital changes, those of noncoplanar types in particular, for small satellites without orbital maneuvering thrusters. …


Energy Consumption And Greenhouse Gas Emissions From Commercial And Manufacturing Sectors Specific Studies On Hvac Equipment And Dairy Processing, Aik Jong Tan May 2012

Energy Consumption And Greenhouse Gas Emissions From Commercial And Manufacturing Sectors Specific Studies On Hvac Equipment And Dairy Processing, Aik Jong Tan

Graduate Theses and Dissertations

Commercial and manufacturing sectors in United States consumed approximately 50% of the total End use energy in 2010. In 2009, 81.5% of the greenhouse gas (GHG) emitted in the United States was energy related. From the broad aspects of commercial and manufacturing sectors; two relatively narrow and specific topics, commercial building's HVAC equipment and dairy processing were chosen to increase the understanding of the energy use and GHG emission in these two sectors. Few published studies related to these two specific areas are available. The first study in this thesis discussed the energy use and GHG emissions by HVAC equipment …


Energy-Based Analysis Of Utility Scale Hybrid Power Systems, Kwame Agyenim-Boateng Dec 2011

Energy-Based Analysis Of Utility Scale Hybrid Power Systems, Kwame Agyenim-Boateng

UNLV Theses, Dissertations, Professional Papers, and Capstones

The promise of large-scale use of renewables such as wind and solar for supplying electrical power is tempered by the sources' transient behavior and the impact this would have on the operation of the grid. Among the methods cited for addressing some of those concerns are exploring the complementary nature of solar and wind power generation, and through the use of supplemental energy storage. While the technology for the latter has not been proven to be economical on a large scale at the present time, some assessments of what magnitude is required can be made. An energy-based analysis of utility …


Fenestration Studies On Building Energy Using The Facade Evaluation Facility, Wendell Cocina Dec 2011

Fenestration Studies On Building Energy Using The Facade Evaluation Facility, Wendell Cocina

UNLV Theses, Dissertations, Professional Papers, and Capstones

The project was developed to assess several types of facades and their influence on building energy, mainly focused on windows and other building fenestrations. Requirements for the facility are stated in this paper alongside corresponding solutions. The facility is designed to represent a section of a building façade. Experimenting on a wide range of fenestrations including windows with integrated PV elements was the primary prerequisite. The option of removable façade configurations was used and allowed testing specimens to be changed effortlessly. Instrumentation and data acquisition are discussed including calibration and uncertainty analysis. Investigation of the air conditioning unit was concluded …


Numerical Simulation Of Thermo-Elasticity, Inelasticity And Rupture Inmembrane Theory, Michael Taylor Oct 2008

Numerical Simulation Of Thermo-Elasticity, Inelasticity And Rupture Inmembrane Theory, Michael Taylor

Mechanical Engineering

Two distinct two-dimensional theories for the modeling of thin elastic bodies are developed. These are demonstrated through numerical simulation of various types of membrane deformation. The work includes a continuum thermomechanics-based theory for wrinkled thin films. The theory takes into account single-layer sheets as well as composite membranes made of multiple lamina. The resulting model is applied to the study of entropic elastic elastomers as well as Mylar/aluminum composite films. The latter has direct application in the area of solar sails. Several equilibrium deformations are illustrated numerically by applying the theory of dynamic relaxation to a finite difference discretization based …


Fluid Flow In Micro-Channels: A Stochastic Approach, Hilda Marino Black Jul 2000

Fluid Flow In Micro-Channels: A Stochastic Approach, Hilda Marino Black

Doctoral Dissertations

In this study free molecular flow in a micro-channel was modeled using a stochastic approach, namely the Kolmogorov forward equation in three dimensions. Model equations were discretized using Central Difference and Backward Difference methods and solved using the Jacobi method. Parameters were used that reflect the characteristic geometry of experimental work performed at the Louisiana Tech University Institute for Micromanufacturing.

The solution to the model equations provided the probability density function of the distance traveled by a particle in the micro-channel. From this distribution we obtained the distribution of the residence time of a particle in the micro-channel. Knowledge of …


A Hybrid Finite Element-Finite Difference Method For Thermal Analysis In A Double-Layered Thin Film, Teng Zhu Apr 2000

A Hybrid Finite Element-Finite Difference Method For Thermal Analysis In A Double-Layered Thin Film, Teng Zhu

Doctoral Dissertations

Thin film technology is of vital importance in microtechnology applications. For instance, thin films of metals, of dielectrics such as SiO2, or Si semiconductors are important components of microelectronic devices. The reduction of the device size to the microscale has the advantage of enhancing the switching speed of the device. The reduction, on the other hand, increases the rate of heat generation that leads to a high thermal load on the microdevice. Heat transfer at the microscale with an ultrafast pulsed-laser is also a very important process for thin films. Hence, studying the thermal behavior of thin films or of …