Mechanical Engineering Commons^™

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic: Quarterly Progress Report (Aug. 01 – Oct. 31, 2002), Yingtao Jiang, Bingmei Fu, Woosoon Yim

Transmutation Sciences Materials (TRP)

After two month intensive work in LANL, some preliminary sensor calibration curves have been obtained. Further data analysis shall be performed to assess the theoretical and measured data. Also, a new experimental apparatus shall be designed and located in UNLV to continue the left work.

Technical Progress:

• A set of calibration curves of voltage vs. temperature ranging from 300⁰C to 500⁰C under various oxygen concentrations in liquid LBE for the YSZ oxygen sensor has been obtained and has been reported in one paper.

• A meeting with LBE committee and other faculty members in AAA …

Distributions Of Nobel Metal Pd And Pt In Mesoporous Silica, J. Arbiol, A. Cabot, J. R. Morante, Fanglin Chen, Meilin Liu

Faculty Publications

Mesoporous silicananostructures have been synthesized and loaded with Pd and Pt catalytic noble metals. It is found that Pd forms small nanoclusters (3–5 nm) on the surface of the mesoporous structure whereas Pt impregnation results in the inclusion of Pt nanostructures within the silica hexagonal pores (from nanoclusters to nanowires). It is observed that these materials have high catalyticproperties for CO–CH₄CO–CH₄CO–CH₄ combustion, even in a thick film form. In particular, results indicate that the Pt and Pd dispersed in mesoporous silica are catalytically active as a selective filter for gas sensors.

A Mechanical System For Soil Reconstruction, John Patrick Fulton, Larry G. Wells, Timothy D. Smith

Biosystems and Agricultural Engineering Faculty Publications

One of the most perplexing problems associated with reclaiming surface–mined lands is excessive compaction of soil due to the heavy earthmoving equipment used during the reclamation process. Over the years, some innovative material handling schemes have been devised to limit vehicle traffic during reclamation on reconstructed soil. However, final grading operations can often create root–limiting bulk densities, which affect plant growth and yield. The purpose of this article is to describe a mechanism designed at the University of Kentucky whereby mine soil can be reconstructed without introducing compaction caused by surface traffic in order for the soil to sustain desirable …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements: Quarterly Progress Report (June 1 – August 31, 2002), Ajit K. Roy

Transmutation Sciences Materials (TRP)

The purpose of this collaborative research project involving the University of Nevada Las Vegas (UNLV), the Idaho State University (ISU), and the Los Alamos National Laboratory (LANL) is to evaluate the feasibility of determining residual stresses in cold-worked, plastically-deformed, and welded materials using a nondestructive method based on positron annihilation spectroscopy. This technique uses γ-rays from a small MeV electron Linac to generate positrons inside the sample via pair production. This method is known to have capabilities of characterizing defects in thick specimens, that could not be accomplished by conventional positron technique or other nondestructive methods. The generated data will …

Object-Oriented Modeling And Fault Detection Of A Powder Feeder For A Laser Metal Deposition System, Robert G. Landers, Michael Gene Hilgers, Frank W. Liou, Bruce M. Mcmillin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

One of the most critical components of a laser metal deposition system is the powder feeder unit. Techniques are required to efficiently design and analyze these systems and to ensure fault tolerance during the operation. In this paper, a model of the powder feeder unit, based on object-oriented abstractions of it components, is developed. This model is modular in that specific components can be efficiently updated or replaced with components that perform a similar function. In addition, the model can be used for simulation allowing for efficient design and analysis. Assurance of the correctness of the powder feeder system is …

Object-Oriented Modeling And Fauly Detection Of A Powder Feeder For A Laser Metal Deposition System, Robert G. Landers, Michael Gene Hilgers, Frank W. Liou, Bruce M. Mcmillin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

One of the most critical components of a laser metal deposition system is the powder feeder unit. Techniques are required to efficiently design and analyze these systems and to ensure fault tolerance during the operation. In this paper, a model of the powder feeder unit, based on object- oriented abstractions of it components, is developed. This model is modular in that specific components can be efficiently updated or replaced with components that perform a similar function. In addition, the model can be used for simulation allowing for efficient design and analysis. Assurance of the correctness of the powder feeder system …

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic: Quarterly Progress Report (May 01 – July 31, 2002), Yingtao Jiang, Bingmei Fu, Woosoon Yim

Transmutation Sciences Materials (TRP)

Accurate measurement of the oxygen concentration in liquid Lead-Bismuth Eutectic (LBE) cooling system is critical in the active control of the corrosion at the interface between LBE and the stainless steel of transport tubes. Currently, LANL (Los Alamos National Laboratory) scientists have employed an automobile-style YSZ (Yttria Stabilized Zirconia) oxygen sensor unit to measure oxygen levels in an engineeringscaled LBE test system. Although the theoretical model for calculating oxygen concentration based on voltage measurement of YSZ sensor in static conditions is well understood, there is an urgent and strong need to obtain a complete set of calibration curves for YSZ …

Development Of A Model For Induction Heating, Randy Clarksean, Yitung Chen

Fuels Campaign (TRP)

There are two coupled equations that must be solved in order to determine the power deposition. The numerical solution of these equations is needed in order to apply a source term within the energy equations. These equations have previously solved in FIDAP. That implementation used modified versions of the momentum and energy equations to provide a mechanism for the solution of two coupled equations. Currently, we want to solve for the induction heating field in addition to the flow field and the energy equation. In order to do this, a mechanism has to be defined within FIDAP to solve these …

Structure And Magnetic Properties Of The Mnbi Low Temperature Phase, Jinbo Yang, William B. Yelon, William Joseph James, Qingsheng Cai, Samit Roy, Naushad Ali

Physics Faculty Research & Creative Works

High purity MnBi low temperature phase has been prepared and analyzed using magnetic measurements and neutron diffraction. The low-temperature phase of the MnBi alloy has a coercivity μ_0iH_c of 2.0 T at 400 K, and exhibits a positive temperature coefficient from 0 to at least 400 K. The neutron data refinement indicated that the Mn atom changes its spin direction from c axis above room temperature to nearly perpendicular to the c axis at 50 K. A canted magnetic structure has been observed below 200 K. The anisotropy field increases with increasing temperature which gives rise to …

Design And Analysis Of A Process For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Yitung Chen, Darrell Pepper, Randy Clarksean

Fuels Campaign (TRP)

UNLV has developed and will continue to develop process models for the analysis of melt casting processes. This work will continue to be performed under the guidance of Argonne National Laboratory (ANL) engineers to ensure that their knowledge and experience benefits the project. The research to be conducted during the second year will center on performing detailed analyses on a conceptual design of an inductively heated skull-crucible casting furnace. Processing conditions will be analyzed, basic models utilized, and detailed heat and mass transfer models will be developed to analyze the most promising processes. The goal of this second year is …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements, Ajit K. Roy

Transmutation Sciences Materials (TRP)

The purpose of this collaborative research project involving the University of Nevada, Las Vegas (UNLV) and Idaho State University (ISU) is to evaluate the feasibility of determining residual stresses of welded (after pre-straining) engineering materials using a new nondestructive technique based on positron annihilation spectroscopy. The proposed technique is to use γ-rays 2 from a small MeV electron Linac to generate positrons inside the sample via pair production. This method can be used for materials characterization and investigation of defects in thick samples that could not be accomplished by conventional positron techniques or other nondestructive methods. The data generated will …

Tests 2023 & 2024: Case Ih Jx 95 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 2097: Mccormick Mtx 110 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Nebraska Summary 383: Agco Rt130 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1805: John Deere 9520 18 Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1804: John Deere 9320t 18 Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1806: John Deere 9520t 18 Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1811: John Deere 9220 18 Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1810: John Deere 9120 18 Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1802: John Deere 8520t 16 Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Nebraska Summary 384: John Deere 6120 Syncroplus Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Tests 2009 & 2010: Case Ih Jx 55 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1801: John Deere 8520 16 Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1808: John Deere 6403 Diesel 9-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Nebraska Summary 386: John Deere 6320 Powrquad Plus 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Nebraska Summary: S422 Mccormick Mtx 125, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Tests 2017 & 2019: Case Ih Jx 75 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Tests 2013 & 2015: Case Ih Jx 65 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 2098: Mccormick Mtx 125 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 2100: Mccormick Mtx 155 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.