Open Access. Powered by Scholars. Published by Universities.®
- Institution
- Publication
- Publication Type
Articles 1 - 6 of 6
Full-Text Articles in Mechanical Engineering
Analysis Of Ternary Chloride Salt Corrosion In High Nickel Alloys, Dimitri Madden, Gowtham Mohan
Analysis Of Ternary Chloride Salt Corrosion In High Nickel Alloys, Dimitri Madden, Gowtham Mohan
Mechanical Engineering ETDs
The United States Department of Energy seeks to improve the efficiency of concentrating solar power technologies by employing thermal energy storage with operating temperatures above 700°C. To meet these goals, the National Solar Thermal Test Facility at Sandia National Laboratories has considered the use of a ternary molten chloride salt for sensible heat storage systems. While favored for low cost, good heat transfer properties, and stability at high temperature, ternary chloride salt also exhibits high corrosive attack. Components of a chloride salt storage system would include piping, valves, tanks, pumps, receivers, and heat exchangers, which would be exposed to high …
Self-Assembly Of Exfoliated Graphene Flakes As Anticorrosive Coatings For Additive Manufactured Steels, Kaleb Hood, Wen Qian, Yi Xia, Savannah Krupa, Annie Dao, Sarah Ahmed, Samuel Olson, Nam Nguyen, Joseph A. Turner, Jun Jiao
Self-Assembly Of Exfoliated Graphene Flakes As Anticorrosive Coatings For Additive Manufactured Steels, Kaleb Hood, Wen Qian, Yi Xia, Savannah Krupa, Annie Dao, Sarah Ahmed, Samuel Olson, Nam Nguyen, Joseph A. Turner, Jun Jiao
Department of Mechanical and Materials Engineering: Faculty Publications
This study demonstrates the feasibility of using liquid exfoliation of expandable graphite into multilayer exfoliated graphene flakes (EGFs) to form a self-assembled thin film on an air–water interface. The film can coat the surface of additive manufactured (AM) steel substrates to enhance surface properties, specifically AM 316 stainless-steel (AM316), AM 8620 steel (AM8620), and samples of the same alloys made by conventional manufacturing (CM) processes. Liquid exfoliation offers a high yield route for an EGF coating that can cover up to 95% of the sample surface with a single application. The thin, flexible EGFs can coat a rough AM metal …
Estimating Remaining Life And Fitness-For-Services Evaluation Of Fuel Piping Systems, Sekar Putri Purwidyasari, Ahmad Isni Kurniawan, Deni Ferdian
Estimating Remaining Life And Fitness-For-Services Evaluation Of Fuel Piping Systems, Sekar Putri Purwidyasari, Ahmad Isni Kurniawan, Deni Ferdian
Journal of Materials Exploration and Findings
Assets life extension are required to predict the design life expiry based on condition and effects of deterioration. The remaining life assessment will answer the questions about timing of the component or equipment will lead to failure and shall be evaluated by inspection and maintenance monitoring. This study elaborates process calculation and analysis by using remaining life assessment and fitness for services method according to API 579-1/ASME FFS-1 for process piping area. The result of remaining useful life estimation and estimated life has been proposed. There are 11 piping systems based on the condition monitoring with thickness measurements. The result …
Investigation Of Oxidation And Corrosion Resistance Of Ni-Based Alloys And Stainless Steels Under Co2 Environments At Elevated Temperatures, Spencer Roy Fultineer
Investigation Of Oxidation And Corrosion Resistance Of Ni-Based Alloys And Stainless Steels Under Co2 Environments At Elevated Temperatures, Spencer Roy Fultineer
Graduate Theses, Dissertations, and Problem Reports
High mechanical strength integrity, high robustness towards oxidation, and high resistance to carburization under CO2 environments at elevated temperatures are usually required for metallic systems that are employed for power generation. INCONEL 625 is a nickel-based superalloy that started development in the 1950s. This material was designed with the distinct purpose of use in high-temperature and high-pressure systems. While various materials possess the physical properties to handle these conditions, the creation of IN625 addresses the need for a material to withstand the highly corrosive properties of these kinds of environments. In order to evaluate the oxidation and corrosion resistance of …
Aqueous Redox Flow Batteries With Boron Doped Diamond As An Electrode., Alex M. Bates
Aqueous Redox Flow Batteries With Boron Doped Diamond As An Electrode., Alex M. Bates
Electronic Theses and Dissertations
As the interest and implementation of renewable energy accelerates, so does that of grid energy storage. It is widely believed that a cost-effective energy storage technology will bring about the proliferation of renewable energy. Redox flow battery (RFB) technology represents a promising solution to cost-effective grid energy storage. Compared to other technologies, RFBs have a long lifetime, high efficiency, are non-flammable, significantly reduce cost, and separately scale power and energy. The separation of power and energy enables increased energy capacity by simply adding electrolyte volume. Of the challenges facing RFB technology, one readily apparent is the cost of the active …
Material-Process-Property Relationships Of 17-4 Stainless Steel Fabricated By Laser-Powder Bed Fusion Followed By Hot Isostatic Pressing., Harish Irrinki
Material-Process-Property Relationships Of 17-4 Stainless Steel Fabricated By Laser-Powder Bed Fusion Followed By Hot Isostatic Pressing., Harish Irrinki
Electronic Theses and Dissertations
17-4 PH stainless steel is commonly used in medical, tooling, automotive, chemical and aerospace industries due to its excellent strength and corrosion properties. Additive manufacturing processes such as laser-powder bed fusion (L-PBF) have gained attention and importance due to the potential to produce complex-shaped three-dimensional parts for various industries. In order to manufacture three-dimensional components from 17-4 PH stainless steel powder using L-PBF, it is critical for design and manufacturing engineers to have an awareness of various material options and corresponding processing and post-processing conditions to obtain useful mechanical properties from the process. The goal of this dissertation is to …