Mechanical Engineering Commons^™

Improving Sizing Resolution Of Particle Impactors In The Nanoparticle Range, Shivuday Kala

All Dissertations

The application of particle size measurement extends across many fields: air quality measurement, pharmaceutical studies, paint and coating production, and nanoparticle formulation to name a few. Therefore, accurate measurement of nanoparticles is critical to aerosol science. While devices currently exist that can size and count nanoparticles such as electrical mobility spectrometers, dynamic light scattering devices, and small angle X-ray scattering devices, their high costs, complex operation, and lack of outdoor usability, restrict their use in practical applications. Among the devices that can size aerosols down to the nanoscale, cascade impactors stand out because of their robustness, relatively simple design, low …

Mechanical Properties Of Permanent Foaming Fixatives For Deactivation & Decommissioning Activities, Tristan Maximilian Simoes-Ponce

FIU Electronic Theses and Dissertations

The Department of Energy is investigating fixative technologies that encapsulate and/or immobilize residual contamination in voids during deactivation and decommissioning (D&D). These technologies must have adequate mechanical and adhesion properties to withstand seismic activity that may occur. One solution is the implementation of polyurethane foams used as permanent foaming fixatives (PFF), specifically intumescent foams that contain expandable graphite, making them fire resistant when exposed to extreme heat conditions.

Tensile, compression, seismic, and tensile adhesion testing was done on six commercial-off-the-self polyurethane foams to determine if the expandable graphite and other filler intumescent technologies improve its mechanical limits. It was found …

Adhesion Testing Of Printed Inks While Varying The Surface Treatment Of Polymer Substrates, Clayton Neff, Edwin Elston, Amanda Schrand, Nathan B. Crane

Faculty Publications

Additive manufacturing with conductive materials enables new approaches to printed electronics that are unachievable by standard electronics manufacturing processes. In particular, electronics can be embedded directly into structural components in nearly arbitrary 3D space. While these methods incorporate many of the same materials, the new processing methods require standard test methods to compare materials, processing conditions, and determine design limits. This work demonstrates a test method to quantitatively measure the adhesion failure of printed inks deposited on a substrate without changing the ink printing conditions. The proposed method is an adaption of single lap shear testing in which the lap …

Enhance Diamond Coating Adhesion By Oriented Interlayer Microcracking, Habio Guo, Xingcheng Xiao, Yue Qi, Zhi-Hui Xu, Xiaodong Li

Xiaodong Li

In this paper, we report a microcrack toughening mechanism for enhancing the adhesion of diamondcoating. The oriented microcracks were formed within the TiC interlayer to dissipate strain energy and accommodate deformation via the crack opening-closing mechanism, thus enhancing the coating/substrate interfacial toughness. The delamination of diamondcoating was effectively prevented when the parallel microcracks were confined within the interlayer and arrested at interfaces of coating/interlayer/substrate. Density functional theory calculations revealed that the highly anisotropicfracture strength of the TiC phase energetically favors crack initiation and propagation along (100) planes only, which are 54.7° away from the interface. These microcracks are constrained inside …

Enhance Diamond Coating Adhesion By Oriented Interlayer Microcracking, Habio Guo, Xingcheng Xiao, Yue Qi, Zhi-Hui Xu, Xiaodong Li

Faculty Publications

In this paper, we report a microcrack toughening mechanism for enhancing the adhesion of diamondcoating. The oriented microcracks were formed within the TiC interlayer to dissipate strain energy and accommodate deformation via the crack opening-closing mechanism, thus enhancing the coating/substrate interfacial toughness. The delamination of diamondcoating was effectively prevented when the parallel microcracks were confined within the interlayer and arrested at interfaces of coating/interlayer/substrate. Density functional theory calculations revealed that the highly anisotropicfracture strength of the TiC phase energetically favors crack initiation and propagation along (100) planes only, which are 54.7° away from the interface. These microcracks are constrained inside …

The Dissipated Power In Atomic Force Microscopy Due To Interactions With A Capillary Fluid Layer, Nicole N. Hashemi, M.R. Paul, H. Dankowicz, W. Jhe

Nastaran Hashemi

We study the power dissipated by the tip of an oscillating micron-scale cantilever as it interacts with a sample using a nonlinear model of the tip-surface force interactions that includes attractive, adhesive, repulsive, and capillary contributions. The force interactions of the model are entirely conservative and the dissipated power is due to the hysteretic nature of the interaction with the capillary fluid layer. Using numerical techniques tailored for nonlinear and discontinuous dynamical systems we compute the exact dissipated power over a range of experimentally relevant conditions. This is accomplished by computing precisely the fraction of oscillations that break the fluid …