Open Access. Powered by Scholars. Published by Universities.®
- Institution
- Publication
- Publication Type
Articles 1 - 4 of 4
Full-Text Articles in Mechanical Engineering
Experimental Characterization And Manufacture Of Polymer Nanocomposite Dielectric Coatings For High-Temperature Superconductor Applications, Jacob Ryan Mahon
Experimental Characterization And Manufacture Of Polymer Nanocomposite Dielectric Coatings For High-Temperature Superconductor Applications, Jacob Ryan Mahon
Theses and Dissertations
Increased implementation of high-temperature superconducting (HTS) power transmission has the potential to revolutionize the efficiency of electrical grids and help unlock a fully electric transportation infrastructure. Realizing the benefits of HTS systems has been impeded by a lack of available dielectric insulation materials that can 1) withstand the extreme cryogenic operating environment of superconductors and 2) demonstrate low temperature processing that is compatible with existing superconductor manufacturing methods. Solving this problem necessitates a high-performance dielectric material with multifunctional properties specifically suited for operation in HTS systems. A polyamide and silicon dioxide (PA/SiO2) nanocomposite material with exceptional thermal stability has been …
Understanding Heterostructure Chemiresistive Gas Sensing At Room Temperature, Yale Wang
Understanding Heterostructure Chemiresistive Gas Sensing At Room Temperature, Yale Wang
Theses and Dissertations
Chemiresistive sensors are the most widely investigated gas sensors due to their ease in fabrication, cost-effectiveness, simplicity of operation, and offer advances in miniaturization. Up to date, typical and well-researched resistive-type sensing materials include semiconductor metal oxides, noble metals, carbon-based nanomaterials (e.g., graphene and carbon nanotubes), and conducting polymers. Gas sensors based on a single material were found difficult to meet the practical requirements for multi-sensing properties, including sensitivity, selectivity, speed of response/recovery, stability, limit of detection, and room temperature operation. Rational design through a combination of chemically or electronically dissimilar nanomaterials is an effective route to enhancing gas sensing …
Novel Design And Synthesis Of Composite Nanomaterials For Lithium And Multivalent Ion Batteries, Wangwang Xu
Novel Design And Synthesis Of Composite Nanomaterials For Lithium And Multivalent Ion Batteries, Wangwang Xu
LSU Doctoral Dissertations
Nowadays, the fast-increasing energy demand for efficient, sustainable and environmentally-friendly energy storage devices remains a significant and challenging issue. Lithium ion batteries (LIBs) have been widely used as commercial energy devices in portable electronics and also shown great promise in upcoming large-scale applications due to their advantages of environmental safety, efficiency in energy delivering and light weight. However, due to their limited capacity, energy densities and cycle ability, LIBs still need further improvement to expand their applications to a larger field, especially electric vehicle (EVs) and hybrid electric vehicles (HEVs), in which energy storage devices with large capacity and high …
Analysis Of Surface Integrity In Machining Of Aisi 304 Stainless Steel Under Various Cooling And Cutting Conditions, F. Klocke, B. Döbbeler, S. Lung, S. Seelbach, Ibrahim S. Jawahir
Analysis Of Surface Integrity In Machining Of Aisi 304 Stainless Steel Under Various Cooling And Cutting Conditions, F. Klocke, B. Döbbeler, S. Lung, S. Seelbach, Ibrahim S. Jawahir
Institute for Sustainable Manufacturing Faculty Publications
Recent studies have shown that machining under specific cooling and cutting conditions can be used to induce a nanocrystalline surface layer in the workspiece. This layer has beneficial properties, such as improved fatigue strength, wear resistance and tribological behavior. In machining, a promising approach for achieving grain refinement in the surface layer is the application of cryogenic cooling. The aim is to use the last step of the machining operation to induce the desired surface quality to save time-consuming and expensive post machining surface treatments. The material used in this study was AISI 304 stainless steel. This austenitic steel suffers …