Modular Composite Sandwich Structures For Thermal And Structural Retrofitting Of Existing Buildings, Marc Al Ghazal

Masters Theses

Around 40% of global energy consumption and 30% of worldwide carbon dioxide (CO2) emissions are attributed to buildings. Most of this consumption is dedicated to ensuring thermal comfort. The goal of this research was to develop and field validate retrofit solutions to improve the energy efficiency of buildings. Exterior cladding panels were designed and tested to ensure adequate thermal and structural performance. Sandwich panels (glass fibers reinforced polymer (GFRP) skins and polymeric foam cores) were fabricated using the vacuum assisted resin transfer molding (VARTM) process. Extruded polystyrene (XPS) and polyurethane (PU) foams were compared as core materials through a series …

Fungi In Flux | Designing Regenerative Materials And Products With Mycelium, Arvind Bhallamudi

Masters Theses

As the world grapples with the escalating crisis of climate threats and environmental degradation, this research delves into the synergistic potential of design and biology, developing safe and sustainable materials for applications in prototyping, furniture and interior design. Harnessing the power of a unique organism - fungi, the study proposes an accessible, efficient, and resilient material resource system. It utilizes local waste streams and mycelium (the vegetative part of fungi) to grow functional structures. An experimental and small-scale protocol is modeled by testing bio-fabrication and bio-printing methods. The composites' performance qualities and characteristics are evaluated through mechanical testing and a …

Correlating Large-Format Additive Manufacturing Processing Parameters To Fiber Length And The Mechanical Performance Of Reinforced Polymer Composites, Andrew Phillip Rhodes

Masters Theses

The Big Area Additive Manufacturing (BAAM) system at Oak Ridge National Laboratory has been used to produce carbon fiber reinforced structures for several years, including vehicles, building constituents, composite tooling, etc. While the development of a large-format polymer additive manufacturing (AM) system has moved quickly, the impact of the BAAM’s extruder on the length of carbon fiber feedstock has not been systematically studied. Numerous studies in processing fiber reinforced thermoplastics in plasticizing and injection molding systems have shown that fibers are subjected to significant shear as they are processed, which can cause a drastic reduction in fiber length which negatively …

Comparative Analysis On Low Cost Continuous Carbon Fiber Polypropylene Composite Using Compression Molding And Automated Tape Placement, Benjamin U. Schwartz

Masters Theses

Carbon fiber reinforced plastics (CFRP) are widely used throughout the aerospace industry where a weight reduction remains the highest priority with less emphasis on cost. Textile grade carbon fiber (TCF) and other low cost carbon fiber (LCCF) alternatives have recently emerged for use in the automotive market where emissions regulations have pushed automotive manufacturers and research institutions to look for cost effective light weight materials. Fiber reinforced thermoplastics provide an effective solution that align with automotive design including low cost, high processing rates, high impact toughness, unlimited shelf life, and recyclability.

TCF and Zoltek_PX35 fibers are two LCCF aimed at …

Optimized 3d-Printing Of Carbon Fiber-Reinforced Polyether-Ether-Ketone (Cfr-Peek) For Use In Overmolded Lattice Composite, Ryan C. Ogle

Masters Theses

Current orthopedic implants are overwhelmingly composed from metallic materials. These implants show superior mechanical properties, but this can additionally result in stress shielding due to a modulus mismatch between the bone tissue and implanted device. Polymeric implants reduce this stress shielding effect but have much lower mechanical properties, limiting their use. Polylactic acid (PLA) is a widely used biodegradable thermoplastic polymer, however, its use has been limited by the polymer’s mechanical properties and rapid loss of strength during degradation in vivo. Polyether-ether-ketone (PEEK) is another common biocompatible polymer , with chemical and mechanical properties which make it a popular alternative …

Assessing Mechanical Performance Of Dissimilar Steel Systems Made Via Wire-Arc Additive Manufacturing, Obed Daniel Acevedo

Masters Theses

Hot stamping is part of a specific type of metalworking procedure widely used in the automotive industry. This research seeks to help make hot stamp tooling component production more cost-effective by using large-scale additive manufacturing. Additive manufacturing can produce dissimilar steel components that can be more cost-effective and time-efficient and allow for complex geometries to be made. A dissimilar steel system consisting of 410 martensitic stainless steel and AWS ER70S-6 mild steel is proposed to make hot stamps, making them more cost-efficient. However, the material interface's mechanical behavior in 410SS-mild steel additively manufactured material systems is not well understood. This …

Tall Timber In Denver: An Exploration Of New Forms In Large Scale Timber Architecture, Andrew P. Weuling

Masters Theses

Wood has been utilized by humans for thousands of years in the construction of our built environment. More recently, our expanded understanding of the material and the advancement of engineered wood have allowed us to use wood like never before. Concrete and steel, however, have emerged as the main materials used in large scale construction in the late 19^th and 20^th Centuries. As we are battling and searching for solutions to climate change, the importance of wood in large scale construction has increased as not only is its carbon intensity is lower than steel and concrete, but its …

On The Investigation Of Hot Tearing Behavior Of Continuous Cast Steel, Yanru Lu

Masters Theses

”Hot tearing has long been recognized as a major problem that plagues the development of the continuous casting process and results in low-quality products. Understanding of the mechanisms and the required conditions for the hot tearing formation is important for industries but has not been well-established yet. Thus, this research focuses on the hot tearing issue observed in continuous cast steel, by providing a summary of the current research progress and then introducing a new laboratory method to determine the thermo-mechanical properties relevant to hot tearing of different steel grades under different solidification conditions. In this method, an apparatus was …

Performance Evaluation Of Alsi10mg Fabricated By A Selective Laser Melting Process, David Michael Murphy

Masters Theses

“Selective laser melting is becoming a widely used additive manufacturing technique that melts metal powder in a layer by layer process in order to build a desired part or geometry. Like many additive processes, selective laser melting allows for fabrication of parts with complex geometries. In order to fabricate a fully dense part there are a number of variables to take into account including: powder characteristics, laser parameters, and environmental parameters. Each of these variables can affect the microstructure and thus the mechanical performance of an additively manufactured part. In this work, the aluminum alloy AlSi10Mg was investigated. AlSi10Mg is …

In-Situ X-Ray Imaging Of The Selective Laser Melting Process, Meelap M. Coday

Masters Theses

"Fusion-based metal additive manufacturing (AM) has garnered much interest in recent decades. Despite the popularity of fusion-based AM technologies such as selective laser melting (SLM), there are still fundamental questions and uncertainties that need to be addressed. In this work, we focus on the understanding of the undercooling in the SLM process and the uncertainties induced by the laser beam size, power, and scan speed. First, we report the estimation of undercooling in the SLM process from the solidification rate measured by in-situ high-speed synchrotron x-ray imaging, based on the dendrite growth velocity model. The undercooling changes as a function …

Optical-Fiber-Based Laser-Induced Cavitation For Dynamic Mechanical Characterization Of Soft Materials, Qian Feng

Masters Theses

In the laser-induced cavitation (LIC) technique, a vapor-gas cavity is generated in water, or a soft material by focusing an intense laser pulse into the sample. The high-strain-rate mechanical properties of these samples can be investigated through a real-time size measurement of the expanding cavity bubble. Although this LIC technique has been applied to multiple research fields such as mechanical, biological and medical areas. It is possible to simplify and improve this LIC method by introducing optical-fibers. In this approach, we propose to employ an optical-fiber to deliver the intense laser pulse to an arbitrary position of an optical opaque …

The Effect Of Cell Size And Surface Roughness On The Compressive Properties Of Abs Lattice Structures Fabricated By Fused Deposition Modeling, Leah Hope Mason

Masters Theses

"Postprocessing is an important step in many manufacturing methods, but it is especially important for additive manufacturing. Researchers looking to improve the surface roughness of acrylonitrile butadiene styrene (ABS) parts fabricated by fused deposition modeling (FDM) have determined that acetone smoothing not only achieves improved surface roughness but increases compressive strength as well. This could be very beneficial to lattice structures, which are known for already having an excellent strength to weight ratio. If the compressive strength of ABS lattice structures could be improved even further using acetone smoothing, it could expand the applications for plastic lattice structures and improve …

Characterization Of The Surface Condition In Aa6061 Resulting From Deep Rolling As A Function Of Common Industrial Parameters, Andrew Kenneth Layer

Masters Theses

"Roller burnishing is widely used in industry to improve the surface finish and fatigue life of components. As weight reduction continues to grow in the automotive and transportation industries, deep rolling can help maintain product performance by mitigating the increase in component stresses resulting from lower weight systems. Deep rolling parameters such as tool, applied angle, feed rate, spindle speeds, and relative tool direction all affect cycle time, product performance, and appearance. The effects of common industrial parameters on the resultant surface roughness and residual stress profiles were studied in this investigation. The samples were manufactured on a CNC lathe …

High Strain Rate Dynamic Response Of Aluminum 6061 Micro Particles At Elevated Temperatures And Varying Oxide Thicknesses Of Substrate Surface, Carmine Taglienti

Masters Theses

Cold spray is a unique additive manufacturing process, where a large number of ductile metal micro particles are deposited to create new surface coatings or free-standing structures. Metallic particles are accelerated through a gas stream, reaching velocities of over 1 km/s. Accelerated particles experience a high-strain-rate microscopic ballistic collisions against a target substrate. Large amounts of kinetic energy results in extreme plastic deformation of the particles and substrate. Though the cold spray process has been in use for decades, the extreme material science behind the deformation of particles has not been well understood due to experimental difficulties arising from the …

Designed Extrudate For Ceramic Additive Manufacturing, Devin Mcmillen

Masters Theses

"The objective of this thesis work was to design ceramic paste systems that assist in achieving a high theoretical density ( > 95%) after deposition by a novel additive manufacturing process, i.e. Ceramic On-Demand Extrusion (CODE). The work is encompassed in five main sections: Sections 1 and 2 provide an introduction and literature review of relevant topics for the following sections of experimentation. Section 3 provides an analysis of a reaction chemistry to identify three discrete materials that could be combined via CODE and result in zirconium diboride (ZrB₂) post-sintering. Section 4 describes the development of a high solids …

Numerical Simulation Of Multi-Phase Core-Shell Molten Metal Drop Oscillations, Kaushal Sumaria

Masters Theses

The surface tension of liquid metals is an important and scientifically interesting parameter which affects many metallurgical processes such as casting, welding and melt spinning. Conventional methods for measuring surface tension are difficult to use for molten metals above temperatures of 1000 K. Containerless methods are can be used to measure the surface tension of molten metals above 1000 K. Oscillating drop method is one such method where a levitated droplet is allowed to undergo damped oscillations. Using the Rayleigh’s theory for the oscillation of force-free inviscid spherical droplets, surface tension and viscosity of the sample can be calculated from …

Cathodic Protection Measurement Through Inline Inspection Technology Uses And Observations, Briana Ley Ferguson

Masters Theses

"This research supports the evaluation of an impressed current cathodic protection (CP) system of a buried coated steel pipeline through alternative technology and methods, via an inline inspection device (ILI, CP ILI tool, or tool), in order to prevent and mitigate external corrosion. This thesis investigates the ability to measure the current density of a pipeline's CP system from inside of a pipeline rather than manually from outside, and then convert that CP ILI tool reading into a pipe-to-soil potential as required by regulations and standards. This was demonstrated through a mathematical model that utilizes applications of Ohm's Law, circuit …

Cold Gas Dynamic Spray – Characterization Of Polymeric Deposition, Trenton Bush

Masters Theses

When a solid, ductile particle impacts a substrate at sufficient velocity, the resulting heat, pressure, and plastic deformation can produce bonding at the interface. The use of a supersonic gas flow to accelerate such particles is known as Cold Spray deposition. The Cold Spray process has been commercialized for some metallic materials, but further research is required to unlock the exciting material properties possible with polymeric compounds. In this work, a combined computational and experimental study a) simulated and optimized the nozzle flow conditions necessary to produce bonding in a polyethylene particle, b) developed and fabricated an experimental device, and …

Synthesis And Photonic Sintering Of Bioresorbable Zinc Nanoparticle Ink For Transient Electronics Manufacturing, Bikram K. Mahajan

Masters Theses

"Zinc is an essential 'trace element' that supports immune systems, and is required for DNA synthesis, cell division, and protein synthesis. Zinc nanoparticles (Zn NP) has antibacterial properties and potential to be used in biodegradable printed electronics devices. The research presented here is about the synthesis of Zn NP and their potential use in transient electronics devices. In Paper 1, a technique of room temperature synthesis of Zn NP is reported using ball milling. Controlled amount of PVP was mixed in the solvent to stabilize the Zn particles and minimize cold welding during milling. The size of the produced Zn …

Hybrid Manufacturing Processes For Fusion Welding And Friction Stir Welding Of Aerospace Grade Aluminum Alloys, Megan Alexandra Gegesky

Masters Theses

"Friction stir welding and processing can provide for joints in aerospace grade aluminum alloys that have preferable material properties as compared to fusion welding techniques. Aerospace grade aluminum alloys such as AA2024-T3 and AA7075-T6 are considered non-weldable by traditional fusion welding techniques. Improved mechanical properties over previously used techniques are usually preferable for aerospace applications. Therefore, by combining traditional fusion welding and friction stir processing techniques, it could be plausible to create more difficult geometries in manufactured parts instead of using traditional techniques. While this combination of fusion welding and friction stir processing is not a new technology, its introduction …

Laser Surface And Sub-Surface Repair During Metal Additive Manufacturing, Prudvi Teja Ravi

Masters Theses

"This study examines the use of laser surface treatment to repair surface and subsurface defects. Numerical analysis was performed on laser surface melting using Gaussian heat distribution equations to analyze the depth of the melt pool created by the phenomena. Concurrently, a process map was developed with a planned set of experiments by varying the ranges of laser power and travel speed to determine the dimensions of the melt pool across the gamut. The data generated from both the process studies and the numerical analysis was then used to determine the ideal operating ranges of the process parameters to repair …

Kinetics Of Aluminization And Homogenization In Wrought H-X750 Nickel-Base Superalloy, Sean Reilly

Masters Theses

In sub-millimeter sheets of wrought H-X750 Nickel-base superalloy, aluminum-rich coatings are bonded to matrix with a vapor phase aluminization process. If an appropriate amount of aluminum is bonded to matrix with homogenization treatment, the resulting diffusion couple will diffuse into coherent (g/g’) heterogeneous phases creating matrix that is both precipitation and solid solution strengthened.

The diffusional mechanisms for solid solution mass transport involved with the growth and dispersion of bonded aluminum-rich coatings in the aluminization process only differ from the no external mass flow homogenization process with annealing treatment in that the boundary conditions are different. In each case these …

Reduced Leak Calibration Uncertainties By The Outgassing Quantification Method, Philip Mason Carper

Masters Theses

Standard leaks are used throughout industry for various applications, such as gas transfer, calibration of mass spectrometers, and calibration of leak detectors. The ability to provide a controlled delivery of gases at relatively low flow rates makes standard leaks a popular choice for calibration standards. This ability also allows for precise quantities of gas to accumulate over time. The accumulation of gas from standard leaks is used as a “transfer standard” for making in-process adjustments to measurement instrumentation. With the advent of tighter quality control constraints, the quantification and control of leak rates is becoming an increasingly important matter, placing …

Effect Of Moisture Absorption On The Sinter Quality Of Central Solenoid (Cs) Coil Pack, Zeshaan Sher Mohammed

Masters Theses

Fusion energy has been said to be the solution to all the world’s energy problems. The International Thermonuclear Experimental Reactor (ITER) is the flagship project to demonstrate the feasibility of fusion energy. The Central Solenoid (CS), an important component of the reactor, is needed to induce plasma current, initiate, ramp-up, ramp-down, and sustain plasma in a very controlled manner. In order to achieve this, the CS coil packs must be manufactured under controlled conditions. The CS conductor is an advanced cable-in-conduit Nb3Sn superconductor. The CS cable will be made in long continuous sections but with thousands of meter of cable …

Elastic And Magnetic Properties Of Tb6fe(Sb,Bi)2 Using Resonant Ultrasound Spectroscopy., David Michael Mccarthy

Masters Theses

Tb6FeSb2 and Tb6FeBi2 are novel rare earth compounds with little prior research. These compounds show high and variable curie temperatures for rare-earth compounds. This has lead to a literature review which includes the discussion of: elasticity, resonance, and magnetism. This review is used to discuss the theory and methodology which can relate these various properties to each other. Furthermore, synthesis, x-ray analysis, and RUS sample preparation of Tb6FeSb2 and Tb6FeBi2 were completed.

Resonant Ultrasound Spectroscopy (RUS) elastic studies were taken for Tb6FeSb2 and Tb6FeBi2 as a function temperature from 5-300K, in various magnetic fields ranging from 0-9T. Tb6FeSb2’s and Tb6FeBi2’s …

The Effects Of Machining On Structure And Tribological Properties Of Ultra High Molecular Weight Polyethylene For Artificial Joint Prostheses, Jinshan Song

Masters Theses

Understanding the effect of machining on the structure and property of subsurface layer of ultra high molecular weight polyethylene (UHMWPE) can significantly facilitate the increase in longevity of artificial joints. This study was performed to investigate the machining effects on the polymeric structure and tribological properties. Machining parameters include cutting speed, tool feed rate and depth of cut. Temperature rise was studied during machining to assess the extent of thermal degradation due to machining. Polymeric structure of the semicrystalline polymer was characterized using differential scanning calorimetry (DSC) in terms of melting enthalpy, crystallinity and melting temperature. Surface texture and hardness …

Mechanical And Tribological Properties Of Composites Of Recycled High Density Polyethylene And Recycled Rubber, Jason G. Boulanger

Masters Theses

This thesis presents a study on the mechanical and tribological properties of composite materials of recycled high density polyethylene (HDPE) and recycled rubber tire particles. The materials were compounded by extrusion and formed into test specimens by injection molding.

The first experiment studied the effect of recycled rubber percentage on mechanical properties of composites of recycled HDPE and recycled rubber. The mechanical properties included tensile strength, percent elongation, hardness, and impact resistance. Recycled rubber concentrations of 0, 5, 10, 15, 20, 25, and 30 percent were tested. The second experiment investigated the tribological properties of recycled HDPE and recycled rubber …

Silicon Carbide/Electroless Nickel Composite Plating For Aluminum Substrates, Ben Charbit

Masters Theses

The effectiveness of producing a composite coating by suspending micron-sized particles in an electroless nickel bath while plating a 2024T4 aluminum alloy part was studied. The variation in the count of particles trapped in the nickel coating due to changes in the particle size, concentration of the particles in the bath, and the substrate surface texture was also studied. Particle sizes of 1 micron and 10 microns, concentrations of 15 gr/lt and 30 gr/lt, and polished and blasted textures were used. It was found that this technique is an effective way to produce composite coatings rendering a high number of …