Mechanical Engineering Commons^™

Novel Ternary Magnesium-Tin Alloys By Microalloying, Sadegh Behdad

FIU Electronic Theses and Dissertations

The objective of this research was to explore the possibility of developing novel Magnesium-Tin alloys with improved mechanical properties by micro-alloying. Magnesium is the lightest of all structural metals. It can be machined faster and with almost half the power required for aluminum. There is a limitless supply of magnesium in sea water and it can also be recycled at 5% of initial energy requirements. These properties make magnesium an ideal green alternative to replace metals and polymers in automotive, aerospace, biomedical and defense sectors. The potential weight reduction in the US automotive market alone, leads to 100 billion gallons …

The Microstructure And The Electrochemical Behavior Of Cobalt Chromium Molybdenum Alloys From Retrieved Hip Implants, Christopher P. Emerson

FIU Electronic Theses and Dissertations

Because of their excellent mechanical, tribological, and electrochemical properties, Cobalt Chromium Molybdenum alloys have been used as the material for both the stem and head of modular hip implants. Corrosion is one mechanism by which metal debris, from these implants, is generated, which can lead to adverse events that requires revision surgery. Manufacturing process such as wrought, as-cast, and powder metallurgy influences the microstructure, material properties, and performance of these implants

The current research focuses on analyzing the microstructure of CoCrMo alloys from retrieved hip implants with optical and scanning electron microscopy. Additionally, energy disperse spectroscopy was utilized to determine …

In-Vivo Corrosion And Fretting Of Modular Ti-6al-4v/Co-Cr-Mo Hip Prostheses: The Influence Of Microstructure And Design Parameters, Jose Luis Gonzalez Jr

FIU Electronic Theses and Dissertations

The purpose of this study was to evaluate the incidence of corrosion and fretting in 48 retrieved titanium-6aluminum-4vanadium and/or cobalt-chromium-molybdenum modular total hip prosthesis with respect to alloy material microstructure and design parameters. The results revealed vastly different performance results for the wide array of microstructures examined. Severe corrosion/fretting was seen in 100% of as-cast, 24% of low carbon wrought, 9% of high carbon wrought and 5% of solution heat treated cobalt-chrome. Severe corrosion/fretting was observed in 60% of Ti-6Al-4V components. Design features which allow for fluid entry and stagnation, amplification of contact pressure and/or increased micromotion were also shown …

Acoustic Manipulation And Alignment Of Particles For Applications In Separation, Micro-Templating, And Device Fabrication, Kamran Moradi

FIU Electronic Theses and Dissertations

This dissertation studies the manipulation of particles using acoustic stimulation for applications in microfluidics and templating of devices. The term particle is used here to denote any solid, liquid or gaseous material that has properties, which are distinct from the fluid in which it is suspended. Manipulation means to take over the movements of the particles and to position them in specified locations.

Using devices, microfabricated out of silicon, the behavior of particles under the acoustic stimulation was studied with the main purpose of aligning the particles at either low-pressure zones, known as the nodes or high-pressure zones, known as …

A Comparison Between Graphene And Ws2 As Solid Lubricant Additives To Aluminum For Automobile Applications, Sara Rengifo

FIU Electronic Theses and Dissertations

The purpose of this thesis was to compare graphene nanoplatelets (GNP) and WS₂ as solid lubricant additives to aluminum in order to reduce friction and wear. The central hypothesis of this work relied on lubricating properties of 2D materials, which consist layers that slip under a shear force.

Two aluminum composites were made (Al-2 vol.% GNP and Al-2 vol.% WS₂) by spark plasma sintering. Tribological properties were evaluated by ball-on-disk wear tests at room temperature (RT) and 200^°C.

WS₂ not only presented the lowest COF (0.66) but also improved the wear resistance of aluminum …