Open Access. Powered by Scholars. Published by Universities.®

Mechanical Engineering Commons

Open Access. Powered by Scholars. Published by Universities.®

Articles 1 - 16 of 16

Full-Text Articles in Mechanical Engineering

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield Jan 2021

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …


Jcati Base Plate, Jacob Atamian Jan 2021

Jcati Base Plate, Jacob Atamian

All Undergraduate Projects

Students of the Mechanical Engineering Technology (MET) program at Central Washington University have contributed to an ongoing Carbon Fiber Recycler project funded by the Joint Center for Aerospace Technology Innovation (JCATI). The goal of this project was to modify the existing recycling system to produce a higher success rate of recycled carbon composite material. This report focuses on increasing the rigidity of the crushing gears so that the deflection occurring among the components during operation was below 0.005 inches to ensure proper operating conditions. The operating speed of the crushing gears was 2.5 rpm with a crushing load of 10,500 …


Mini Rc Baja Car, Jason Schindler Jan 2021

Mini Rc Baja Car, Jason Schindler

All Undergraduate Projects

Incorporating each aspect of engineering incorporated into a senior project is difficult. That is why an RC Baja car is a great senior project for Mechanical Engineering students. The approach that students must take to design, construct, and test the car is to set parameters, and to make overall goals that can be easily measured. These goals include, but not limited to things like a $700 budget and the ability to withstand a 1-foot drop to a flat surface on all four wheels simultaneously. First, the design must meet the specifications and rules that are set previously. This ensures that …


Jcati Carbon Fiber Recycling Shredder, Benjamin Cooley Jan 2021

Jcati Carbon Fiber Recycling Shredder, Benjamin Cooley

All Undergraduate Projects

Once carbon fibers are cast into a resin and used in a composite material, retrieving those fibers can be a difficult task. However, it is beneficial to recycle and reuse the fibers from old unneeded components rather than pay the cost of acquiring new ones. The Joint Center for Aerospace Technology Innovation (JCATI) carbon fiber recycling device condenses the multistep process of extracting the fibers by integrating all steps into one automated device. In the previous version of the device, the cutting blades turned the long composite strips into thin fingers but did not sever them across the width.

The …


Balsa Wood Bridge, Andrew Harris Jan 2021

Balsa Wood Bridge, Andrew Harris

All Undergraduate Projects

Faculty at Central Washington University proposed a challenge to mechanical engineering students that could be accomplished in an in-home setting. The goal was to create a balsa wood bridge, weighing no more than 85 grams, that can support a load over an open span and raise above its resting position by means of a mechanical system. To produce a successful solution to the problem, a vertical lift bridge was created consisting of two lifting towers and a load bearing bridge. Using equations of static equilibrium and strength of materials, the required width for each member was determined. Project requirements were …


Jcati Pyrolysis System, Jack Dutton Jan 2021

Jcati Pyrolysis System, Jack Dutton

All Undergraduate Projects

The Joint Center for Aerospace Technology Innovation (JCATI) project is designed to recycle carbon fiber pieces for use in manufacturing. Part of the system requires the removal of resin from the carbon fibers to facilitate the recycling of carbon fiber. To accomplish this task the pyrolysis process is implemented using a commercial grade oven with a conveyor system. Argon gas is injected into the shroud and over the oven to purge the interior of oxygen. The conveyor system enables this to be a batch process. A ramp is used to allow simple addition of material to the conveyor system and …


Rc Mini Baja Car - Suspension And Chassis, Collin Mckenzie Jan 2020

Rc Mini Baja Car - Suspension And Chassis, Collin Mckenzie

All Undergraduate Projects

Two students have developed a unique design of the RC Baja Car to optimize functionality and performance. A Baja car is a remote controlled 1/10 scale car that is used for recreation or competition, usually meant for competing in the ASME Baja car competition versus various schools. The competition focuses on the best time achieved in different courses that utilize speed, turns, and jumps. The objective for the project was to create a unique suspension from previous individual’s projects by creating a four-link suspension in which allows more travel in the suspension of the car and maintains functionality with the …


Feed Control: Composite Recycle, Rosy Perez Jan 2019

Feed Control: Composite Recycle, Rosy Perez

All Undergraduate Projects

The Boeing Company gave Central Washington University an opportunity for students to research and come up with an idea to reduce costs and landfill waste caused by the trimmings from the 777x composite wing pieces. The engineering and manufacturing for this project is about transporting composite material through to the delamination and chipper process. The delamination process uses a ram to press two claw shaped devices together that bends and deforms the material in opposite directions. The chipper process uses counter rotating saw blades spaced 1/8” apart to produce small shredded material. It is important for this newly designed feed …


Stair Climbing Hand Truck, James Mcpherson Jan 2019

Stair Climbing Hand Truck, James Mcpherson

All Undergraduate Projects

Abstract

Getting a heavy object up a flight of stairs usually requires a team of two or more people. Even with a team of people, the task is often still difficult, dangerous, and possibly insurmountable by one person. This problem is especially prevalent in for those who are moving into apartment complexes. Most apartment complexes have many buildings with two or more floors of living quarters, and elevators are often missing. This project sought to offer a solution to this problem. The solution in question; a motorized hand-truck with 2, trigonal planar pinwheels in place of the stock wheels. The …


Autojack - Hydraulic Powertrain System, Tyce Vu Jan 2019

Autojack - Hydraulic Powertrain System, Tyce Vu

All Undergraduate Projects

A primary problem for mechanics and automotive enthusiasts is the risk associated with lifting and securing a vehicle with conventional jack stands. Often times, improper jack-stand installation results in the vehicle collapsing unexpectedly, causing injury and/or death. This problem can be minimized through the application of a newly re-designed vehicle lifting system. The conventional method for lifting cars is time consuming and can be unsafe in many circumstances. A better, safer, and more efficient lift design was needed; the AutoJack. The approach of the AutoJack design was entirely focused on the safety of lifting a vehicle. Safety was improved by …


Tensile Specimen Punch, John Allen Jan 2017

Tensile Specimen Punch, John Allen

All Undergraduate Projects

This project comes from a need to have tensile specimens made for the MET 351, Metallurgy/Materials and Processes, and 426, Applied Strengths of Materials, labs. This punch is designed to be used with an arbor press to create the desired tensile specimen shape out of plastic blanks. The initial concept was suggested by Dr. Craig Johnson. The designs went through many changes, for example getting rid of the sides originally proposed to hold the specimen in place, and modifications to other parts to make them more efficient. Additional parts were also added to the design with the help and advice …


Built-In Bicycle Rack For Cars, Scott A. Hansberry Jan 2017

Built-In Bicycle Rack For Cars, Scott A. Hansberry

All Undergraduate Projects

Transporting a bicycle after riding somewhere and then needing to be pickup can be problematic. Bicycles will not fit in most vehicles without removing components. There is also the risk of damaging the inside of the vehicle. Expecting everyone to have a bike rack for their vehicle is unrealistic because the bike rack could be considered unappealing visually, take up to much space in the trunk, or limit the vehicle owner’s access to the trunk. The solution to this problem is a bike rack that mounts onto your car and then mounts your bike onto the rack. Most people don’t …


Composite Cold Expansion Tooling, Andrew Amos Jan 2017

Composite Cold Expansion Tooling, Andrew Amos

All Undergraduate Projects

In the world of aircraft manufacturing, cold expansion products literally hold these aircraft together. The problem faced today is that the Little Brute Hydraulic Puller designed and built by Fatigue Technology Inc. is a handheld steel hydraulic cylinder that is heavy and expensive to produce. In a market that demands continuous improvement, there is a constant push to make the product cheaper, better and lighter. In order to accomplish this demand a composite tube will be substituted in the design as the primary pressure cylinder instead of the traditional steel pressure cylinder in order to create a lighter and cheaper …


Multi-Use Fireline Handtool, Bruce W. Bernard Jr Jan 2016

Multi-Use Fireline Handtool, Bruce W. Bernard Jr

All Undergraduate Projects

A wildland firefighter is a valuable resource to protecting public lands and managing fuels. The many hand tools used by firefighters aid in their ability to complete any required tasks effectively. Several of the tools available are specially purposed for individually grubbing, scraping, or liming. A small squad of firefighters could become a more effective resource if the tools they carried could perform several of these purposes as one single tool. To improve the effectiveness of an individual on the fireline a multi-use hand tool was designed to include an axe for liming and a heavy duty scraper for grubbing …


Paper Core Feeder System, Sergio Flores Velez Jan 2016

Paper Core Feeder System, Sergio Flores Velez

All Undergraduate Projects

Paragon Films has always strived to increase productivity and decrease waist within their company. The plant located in Union Gap, Washington currently has two production lines operating 24/7 managed by 2 to 3 people. The heavy line produces 5000 to 10000 revolutions per roll. This production line has a three part system that automatically feeds the paper cores to the spool shafts to roll the films. Therefore, the employees during that shift do not have to worry about filling up the bin very often. On the other hand, the second production line, which produces the hand films, does not have …


Conversion Casting: Adapter Hub, Joseph M. Coup Jan 2016

Conversion Casting: Adapter Hub, Joseph M. Coup

All Undergraduate Projects

The concept of conversion casting makes manufacturing major components much more efficient with regards to time and cost. The conversion cast of the adapter hub used in the Victair Mistifier is a major component that requires 8 hours to machine. The existing hub starts from steel stock and then that block of steel is placed into a CNC machine and coded in to create the adapter hub. The manufacturing method changes to a casting for the adapter hub will create a replicated part that requires 1.5 hours of post machining. The intricate design makes a conversion to casting more effective …