Open Access. Powered by Scholars. Published by Universities.®
- Keyword
-
- 3D Printing (1)
- AZ-9260 (1)
- Bio-inspired Scaffold (1)
- Computational (1)
- Cooperative (1)
-
- Electronic Packaging (1)
- Etch Rate (1)
- Fatigue (1)
- Finite Element Analysis (1)
- Heat transfer (1)
- Interconnects (1)
- Manufacturing (1)
- Materials (1)
- Membrane (1)
- Metallurgy (1)
- Model (1)
- Multiscale Modeling (1)
- Nitrided Stainless Steel Piston Rings (1)
- Phase field (1)
- Photochemical Etching (1)
- Porous (1)
- Reliability (1)
- Robotics (1)
- Scaling (1)
- Service learning (1)
- Simulation (1)
- Solder (1)
- Steel (1)
- Substitution (1)
- Surface Texture (1)
Articles 1 - 6 of 6
Full-Text Articles in Mechanical Engineering
Development Of A Rapid Fatigue Life Testing Method For Reliability Assessment Of Flip-Chip Solder Interconnects, Cody Jackson Marbut
Development Of A Rapid Fatigue Life Testing Method For Reliability Assessment Of Flip-Chip Solder Interconnects, Cody Jackson Marbut
Graduate Theses and Dissertations
The underlying physics of failure are critical in assessing the long term reliability of power packages in their intended field applications, yet traditional reliability determination methods are largely inadequate when considering thermomechanical failures. With current reliability determination methods, long test durations, high costs, and a conglomerate of concurrent reliability degrading threat factors make effective understanding of device reliability difficult and expensive. In this work, an alternative reliability testing apparatus and associated protocol was developed to address these concerns; targeting rapid testing times with minimal cost while preserving fatigue life prediction accuracy. Two test stands were fabricated to evaluate device reliability …
Photochemical Etching Of Nitrided Stainless Steel Piston Rings, Steven Sonntag
Photochemical Etching Of Nitrided Stainless Steel Piston Rings, Steven Sonntag
Mechanical Engineering Undergraduate Honors Theses
Piston rings are designed to provide a seal between the piston and the cylinder wall of internal combustion engines, keeping oil from the crankcase from getting into the combustion chamber. This means piston rings are the main point of contact between the piston and the cylinder wall, which causes the piston to experience high amounts of friction and wear. By texturing the surfaces of the cylinder wall and/or the piston ring, the amount of contact area can be reduced, allowing for less friction, slower wear, and better gas mileage. In this thesis experiments, photochemical etching processes were developed to etch …
Optimization Of The Practice Of Slow Cooling Steel Bars: A Redesign And Modernization Of Materials, Eryn Johnston
Optimization Of The Practice Of Slow Cooling Steel Bars: A Redesign And Modernization Of Materials, Eryn Johnston
Mechanical Engineering Undergraduate Honors Theses
Throughout the process of steel making, certain grades of steel are a higher risk for defects caused by the inability to quickly diffuse hydrogen through the steel when cooled to room temperature at a normal rate based on the ambient air temperature. To reduce the hydrogen flaking defects that are caused due to hydrogen entrapment in the steel, the process of slow cooling is utilized. This process reduces the cooling rate of steel bars by keeping them at a higher temperature for extended periods and in turn gives the hydrogen a chance to fully dissipate from the steel. In many …
A Scalable, Chunk-Based Slicer For Cooperative 3d Printing, Jace J. Mcpherson
A Scalable, Chunk-Based Slicer For Cooperative 3d Printing, Jace J. Mcpherson
Computer Science and Computer Engineering Undergraduate Honors Theses
Cooperative 3D printing is an emerging technology that aims to increase the 3D printing speed and to overcome the size limit of the printable object by having multiple mobile 3D printers (printhead-carrying mobile robots) work together on a single print job on a factory floor. It differs from traditional layer-by-layer 3D printing due to requiring multiple mobile printers to work simultaneously without interfering with each other. Therefore, a new approach for slicing a digital model and generating commands for the mobile printers is needed, which has not been discussed in literature before. We propose a chunk-by-chunk based slicer that divides …
A Numerical Investigation Of Bio-Inspired Scaffolds And Surface Textures, Yucong Gu
A Numerical Investigation Of Bio-Inspired Scaffolds And Surface Textures, Yucong Gu
Graduate Theses and Dissertations
Synthetic scaffolds are widely used as implants to repair bone fracture. Without a proper design, scaffolds could pose significant health risks to the patient and fail to heal the bone properly. A good synthetic scaffold needs to have high porosity and large pore size to allow new bone cells to form on it. However, a scaffold with higher porosity and larger pore size tends to have reduced mechanical strength. Thus, it is important to find a structural design which allows the implant to have a high porosity and large pore size while retaining high strength. In this research, a 3D-printable …
Phase Field Model Of Thermally Induced Phase Separation (Tips) For The Formation Of Porous Polymer Membranes, Ashley Green, Aria Green
Phase Field Model Of Thermally Induced Phase Separation (Tips) For The Formation Of Porous Polymer Membranes, Ashley Green, Aria Green
Mechanical Engineering Undergraduate Honors Theses
Most membrane research and development has been done through experimental work, which can be costly and time consuming. An accurate computational model would greatly reduce the need for these experiments. The focus of the research presented in this paper is to create an accurate computational model for membrane formation using thermally induced phase separation (TIPS). A phase field model is employed to create this model including the Cahn Hilliard Equation and Flory Huggins Theory. This model produced computational results that correspond well with theoretical and experimental results. The model was then adapted to correspond to the PVDF/DPC polymer-solvent system by …