Mechanical Engineering Commons^™

Reclamation Of Fused Silica From Investment Shells Used For Casting Steel, Samuel L. Holt

Electronic Theses and Dissertations

Fused silica is widely used for investment casting shell molds. Fused silica shells are discarded after being used for casting one time. This is due to the transformation of fused silica to beta cristobalite above 1652℉ (900℃). To reduce cost and waste of investment casting foundries, this study is exploring a method to inhibit transformation of fused silica and reclaim it from high temperature investment casting shells. This research has employed firing to minimalize fused silica transformation to cristobalite. The phase transformation is minimalized due to sintering and coarsening of the particles during firing. Coarsening reduces surface area to volume …

Impact Of Sintering Time And Temperature On Mechanical Properties In Projection Sintering Of Polyamide-12, Justin Nussbaum, Taranjot Kaur, Julie Harmon, Nathan B. Crane

Faculty Publications

In powder bed fusion additive manufacturing (AM), the fusing process is temperature and time dependent. However, little work has been done to understand how different processing temperatures and times might impact the mechanical properties at longer sintering times than are typical in laser sintering (LS) systems. Prior results with projection sintering have shown that heating for longer times (>1s) improves part toughness compared to laser sintering. In this work, Large Area Projection Sintering (LAPS) is used to sinter entire layers of material simultaneously over the course of a few seconds with spatial control of layer temperature. This work evaluates …

Experimental And Numerical Study Of Process Parameters Effects Towards Part Quality And Porosity During Powder Bed Additive Manufacturing Processes., Subin Shrestha

Electronic Theses and Dissertations

Powder bed additive manufacturing (PB-AM) process utilizes an electron beam or a laser as a heat source to melt the metallic powder particles. These processes have the capability of freeform fabrication, however certain defects such as porosity, high surface roughness, etc. would hinder its application. It is important to understand the effect of the process parameters and the underlying physical phenomena, which lead to the formation of such defects. In this regard, a three-dimensional (3D) thermo-fluid model is developed to study the effect of beam speed on the surface morphology during powder bed electron beam additive fabrication (PB-EBAF). Besides, the …

3d-Printed Biomimetic Bioactive Glass Scaffolds For Bone Regeneration In Rat Calvarial Defects, Krishna C. R. Kolan, Yue-Wern Huang, Julie A. Semon, Ming-Chuan Leu

Biological Sciences Faculty Research & Creative Works

The pore geometry of scaffold intended for the use in the bone repair or replacement is one of the most important parameters in bone tissue engineering. It affects not only the mechanical properties of the scaffold but also the amount of bone regeneration after implantation. Scaffolds with five different architectures (cubic, spherical, x, gyroid, and diamond) at different porosities were fabricated with bioactive borate glass using the selective laser sintering (SLS) process. The compressive strength of scaffolds with porosities ranging from 60% to 30% varied from 1.7 to 15.5 MPa. The scaffold's compressive strength decreased significantly (up to 90%) after …

An Investigation Of High-Speed Consolidation And Repair Of Carbon Fiber - Epoxy Composites Through Ultrasonic Welding, David A. Hoskins

LSU Master's Theses

Adhesive repair of carbon fiber composite structures is commonly done on damaged structures to extend the service life. This method requires careful preparation of the damaged surface with intricate steps to ensure good bonding between the repair patch and the parent structure by means of an adhesive film. As with many forms of composite manufacturing, it is required to perform vacuum bagging, debulking, and a heated cure depending on the resin. All these steps make the repair process costly and time consuming.

In this present work, an alternative method of repair is investigated which explores the experimental feasibility of using …

Micro-Ct Evaluation Of Defects In Ti-6al-4v Parts Fabricated By Metal Additive Manufacturing, Haijun Gong, Venkata Karthik Nadimpalli, Khalid Rafi, Thomas Starr, Brent Stucker

Department of Manufacturing Engineering Faculty Research and Publications

In this study, micro-computed tomography (CT) is utilized to detect defects of Ti-6Al-4V specimens fabricated by selective laser melting (SLM) and electron beam melting (EBM), which are two popular metal additive manufacturing methods. SLM and EBM specimens were fabricated with random defects at a specific porosity. The capability of micro-CT to evaluate inclusion defects in the SLM and EBM specimens is discussed. The porosity of EBM specimens was analyzed through image processing of CT single slices. An empirical method is also proposed to estimate the porosity of reconstructed models of the CT scan.

Effect Of Architecture And Porosity On Mechanical Properties Of Borate Glass Scaffolds Made By Selective Laser Sintering, Krishna C. R. Kolan, Ming-Chuan Leu, Greg Hilmas, Taylor Comte

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The porosity and architecture of bone scaffolds, intended for use in bone repair or replacement, are two of the most important parameters in the field of bone tissue engineering. The two parameters not only affect the mechanical properties of the scaffolds but also aid in determining the amount of bone regeneration after implantation. Scaffolds with five different architectures and four porosity levels were fabricated using borate bioactive glass (13-93B3) using the selective laser sintering (SLS) process. The pore size of the scaffolds varied from 400 to 1300 μm. The compressive strength of the scaffolds varied from 1.7 to 15.5 MPa …

Effect Of Process Parameters On The Weld Quality In Laser Welding Of Az31b Magnesium Alloy In Lap Joint Configuration, Masoud Harooni, Blair Carlson, Radovan Kovacevic

Mechanical Engineering Research

Magnesium is the lightest structural metal; therefore it has been used in a variety of industries such as automotive, aerospace, electronics and defense. Among different joining processes, laser welding is advantageous due to its low heat input, high depth-to-width weld ratio and good mechanical properties. In this study, a fiber laser is used to weld AZ31B magnesium alloy in a lap joint configuration. Pores were formed in the weld bead that are caused by a thick oxide layer existing on the surface of as-received AZ31B samples. Process parameters including laser power and welding speed are studied to determine their effects …

Mitigation Of Pore Generation In Laser Welding Of Magnesium Alloy Az31b In Lap Joint Configuration, Masoud Harooni, Fanrong Kong, Blair Carlson, Radovan Kovacevic

Mechanical Engineering Research

Magnesium, as the lightest structural metal, has been widely used in the automotive and aerospace industries. Porosity is the main issue in the welding of magnesium alloys and can be caused by surface coatings, hydrogen gas, pre-existing porosity, the collapse of an unstable keyhole and vaporization of alloying elements. In this study, the effect of the oxide layer on pore generation in the welding of AZ31B-H24 magnesium alloy is investigated. A fiber laser with a power of up to 4 kW is used to weld samples in a lap joint configuration. Two groups of samples are studied: as received (AR) …

Mitigation Of Pore Generation In Laser Welding Of Magnesium Alloy Az31b In Lap Joint Configuration, Masoud Harooni, Fanrong Kong, Blair Carlson, Radovan Kovacevic

Masoud Harooni

Magnesium, as the lightest structural metal, has been widely used in the automotive and aerospace industries. Porosity is the main issue in the welding of magnesium alloys and can be caused by surface coatings, hydrogen gas, pre-existing porosity, the collapse of an unstable keyhole and vaporization of alloying elements. In this study, the effect of the oxide layer on pore generation in the welding of AZ31B-H24 magnesium alloy is investigated. A fiber laser with a power of up to 4 kW is used to weld samples in a lap joint configuration. Two groups of samples are studied: as received (AR) …

Effect Of Particle Size, Binder Content And Heat Treatment On Mechanical Properties Of 13-93 Bioactive Glass Scaffolds, Krishna C. R. Kolan, Ming-Chuan Leu, Greg Hilmas, Mariano Garcia Velez

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Particle size, binder content and the post-processing schedule are important parameters that affect the microstructure, and, hence, the mechanical properties of parts produced using the indirect selective laser sintering process. 13-93 bioactive glass, with mean particle sizes ranging from 10 μm to 44 μm, is mixed with different amounts of stearic acid binder to fabricate green scaffolds. Through the design of the post-processing schedule, the time required for postprocessing the green scaffolds is reduced from the initial 80 hrs to 12 hrs. The compressive strength varies from 41 MPa for a part with~60% porosity to 157 MPa for a part …

Noble Metal Nanostructures Synthesized Inside Mesoporous Nanotemplate Pores, J. Arbiol, E. Rossinyol, A. Cabot, F. Peiró, A. Cornet, J. R. Morante, Fanglin Chen, Meilin Liu

Faculty Publications

Noble metal impregnation has resulted in the inclusion of metal nanostructures within the SBA-15 mesoporous silica hexagonal pores (from nanoclusters to nanowires). A bright-field transmission electron microscopy three-dimensional reconstruction is proposed to analyze the localization of nanostructures within the pores of mesoporous nanotemplates. The method allows corroboration whether the nanostructures are synthesized inside the pores or they are synthesized alternatively on the nanotemplate aggregates exterior surface.