Mechanical Engineering Commons^™

Thermal Removal Of Carbon Dioxide From The Atmosphere: Energy Requirements And Scaling Issues, Ted Von Hippel

Ted von Hippel

I conduct a systems-level study of direct air capture of CO2 using techniques from thermal physics. This system relies on a combination of an efficient heat exchanger, radiative cooling, and refrigeration, all at industrial scale and operated in environments at low ambient temperatures. While technological developments will be required for such a system to operate efficiently, those developments rest on a long history of refrigeration expertise and technology, and they can be developed and tested at modest scale. I estimate that the energy required to remove CO2 via this approach is comparable to direct air capture by other techniques. The …

The Impact Of Trees On Passive Survivability During Extreme Heat Events In Warm And Humid Regions, Ulrike Passe, Janette R. Thompson, Baskar Ganapathysubramanian, Boshun Gao, Breanna L. Marmur

Breanna L. Marmur

Communities are increasingly affected by excessive heat. The likelihood of extreme heat events is predicted to increase in the Midwest region of the United States. By mid-century (2036–2065), one year out of 10 is projected to have a 5-day period that is 13°F warmer than a comparable earlier period (1976–2005). The frequency of high humidity/dew point days (“extra moist tropical air mass days,” MT++ synoptic climate classification system) has also increased significantly during a similar period (1975–2010) and between 2010 and 2014 included 8 of 26 heat events. This impact is exacerbated by the fact that many residences in low-income …

Call For Abstracts - Resrb 2019, July 8-9, Wrocław, Poland, Wojciech M. Budzianowski

Wojciech Budzianowski

No abstract provided.

2018-19 Tla Application - Thermal Fluid Sequence, M. A. Rafe Biswas

M. A. Rafe Biswas

No abstract provided.

Dynamical Thermal Conductivity Of Suspended Graphene Ribbons In The Hydrodynamic Regime, Zlatan Aksamija, Arnab K. Majee

Zlatan Aksamija

Jual Obat Kuat Viagra Asli Pfizer 100mg Di Jakarta, Obat Kuat Viagra

Toko Online Obat Kuat Viagra Pfizer | Obat Kuat Pria

Induction Heating Of Thin Films, Paul L. Bergstrom, Melissa L. Trombley

Paul Bergstrom

A method of performing regional heating of a system having a substrate. The method may include applying a thin film to the system, and controllably energizing a coil positioned near the thin film. The energized coils thereby generate a magnetic flux. The method further includes inducing a current in the thin film with the magnetic flux thereby heating the system.

Presentation Of Double Inlet Scpp, Nima Fathi, Seyed Sobhan Aleyasin, Patrick Wayne, Peter Vorobieff

Nima Fathi

No abstract provided.

Evaluation And Enhancement Of Clean Energy Systems: Analytical, Computational And Experimental Study Of Solar And Nuclear Cycles, Nima Fathi

Nima Fathi

Us Patent 9,702,573: Nested Heat Transfer System, Sanza Kazadi

Sanza Kazadi

Effects Of Temperature Change On Interfacial Delamination In Thermal Barrier Coatings, Hossein Ebrahimi, Soheil Nakhodchi

Hossein Ebrahimi

No abstract provided.

La0.7Sr0.3Fe0.7Ga0.3O3-Δ As Electrode Material For A Symmetrical Solid Oxide Fuel Cell, Zhibin Yang, Yu Chen, Chao Jin, Guoliang Xiao, Minfang Han, Fanglin Chen

Fanglin Chen

In this research, La_0.7Sr_0.3Fe_0.7Ga_0.3O_3−δ (LSFG) perovskite oxide was successfully prepared using a microwave-assisted combustion method, and employed as both anode and cathode in symmetrical solid oxide fuel cells. A maximum power density of 489 mW cm⁻² was achieved at 800 °C with wet H₂ as the fuel and ambient air as the oxidant in a single cell with the configuration LSFG|La_0.8Sr_0.2Ga_0.83Mg_0.17O_3−δ|LSFG. Furthermore, the cells demonstrated good stability in H₂ and acceptable sulfur tolerance.

Zespół Energii Odnawialnej I Zrównoważonego Rozwoju (Eozr), Wojciech M. Budzianowski

Wojciech Budzianowski

No abstract provided.

Thermodynamic Analysis Of Separation Systems, Y. Demirel

YASAR DEMIREL

Separation systems mainly involve interfacial mass and heat transfer as well as mixing. Distillation is a major separation system by means of heat supplied from a higher temperature level at the reboiler and rejected in the condenser at a lower temperature level. Therefore, it resembles a heat engine producing a separation work with a rather low efficiency. Lost work (energy) in separation systems is due to irreversible processes of heat, mass transfer, and mixing, and is directly related to entropy production according to the Gouy-Stodola principle. In many separation systems of absorption, desorption, extraction, and membrane separation, the major irreversibility …

Measurement Of The Rate Of Hydrogen Peroxide Thermal Decomposition In A Shock Tube Using Quantum Cascade Laser Absorption Near 7.7 Μm, M. B. Sajid, Et. Es-Sebbar, T. Javed, C. Fittschen, A. Farooq

Dr. Et-touhami Es-sebbar

Hydrogen peroxide (H2O2) is formed during hydrocarbon combustion and controls the system reactivity under intermediate temperature conditions. Here, we measured the rate of hydrogen peroxide decomposition behind reflected shock waves using midinfrared absorption of H2O2 near 7.7 µm. We performed the experiments in diluted H2O2/Ar mixtures between 930 and 1235 K and at three different pressures (1, 2, and 10 atm). Under these conditions, the decay of hydrogen peroxide is sensitive only to the decomposition reaction rate, H2O2 + M → 2OH + M (k1). The second-order rate coefficient at low pressures (1 and 2 atm) did not exhibit any …

A Case Study Of Heat Treatment On Aisi 1020 Steel, Sayed Shafayat Hossain, Md. Maksudul Islam, Md. Sajibul Alam Bhuyan

Md. Maksudul Islam

Proper heat treatment of steels is one of the most important factors in determining how they will perform in service. Engineering materials, mostly steel, are heat treated under controlled sequence of heating and cooling to alter their physical and mechanical properties to meet desired engineering applications. In this study we have chosen AISI 1020 steel as for our research work and we have tried to find out the mechanical properties (hardness) and micro structural properties (martensite formation, carbon self-locking region) by means of appropriate heat treatment process (annealing, normalizing & hardening). Here the steel specimens were heat treated in a …

An Experimental And Modeling Study Of Formaldehyde And 1,3,5-Trioxane Flame Chemistry, Jeffrey S. Santner, Francis M. Haas, Frederick L. Dryer, Yiguang Ju

Francis (Mac) Haas

Evaluation Of Thermal Radiation Effects On Apparent Propagation Rates Of High Pressure Spherical Flames, Jeffrey S. Santner, Francis M. Haas, Yiguang Ju, Frederick L. Dryer

Francis (Mac) Haas

Measurements Of Nh3 Linestrengths And Collisional Broadening Coefficients In N2, O2, Co2, And H2o Near 1103.46 Cm−1, Kyle Owen, Et-Touhami Es-Sebbar, Aamir Farooq

Dr. Et-touhami Es-sebbar

Laser-based ammonia gas sensors have useful applications in many fields including combustion, atmospheric monitoring, and medical diagnostics. Calibration-free trace gas sensors require the spectroscopic parameters including linestrengths and collisional broadening coefficients to be known. Ammonia's strong ν2 vibrational band between View the MathML source has the high absorption strength needed for sensing small concentrations. Within this band, the 1103.46 cm−1 feature is one of the strongest and has minimal interference from CO2 and H2O. However, the six rotational transitions that make up this feature have not been studied previously with absorption spectroscopy due to their small line spacing ranging from …

Effects Of N2o And O2 Addition To Nitrogen Townsend Dielectric Barrier Discharges At Atmospheric Pressure On The Absolute Ground-State Atomic Nitrogen Density, Et. Es-Sebbar, N. Gherardi, F. Massines

Dr. Et-touhami Es-sebbar

Absolute ground-state density of nitrogen atoms N (2p3 4S3/2) in non-equilibrium Townsend dielectric barrier discharges (TDBDs) at atmospheric pressure sustained in N2/N2O and N2/O2 gas mixtures has been measured using Two-photon absorption laser-induced fluorescence (TALIF) spectroscopy. The quantitative measurements have been obtained by TALIF calibration using krypton as a reference gas. We previously reported that the maximum of N (2p3 4S3/2) atom density is around 3 × 1014 cm−3 in pure nitrogen TDBD, and that this maximum depends strongly on the mean energy dissipated in the gas. In the two gas mixtures studied here, results show that the absolute N …

Laminar Natural Convection From Isothermal Vertical Cylinders: Revisiting A Classical Subject, Jerod Day, Matthew Zemler, Matthew Traum, Sandra Boetcher

Sandra Boetcher

No abstract provided.

Determination Of Kinetic Parameters From The Thermogravimetric Data Set Of Biomass Samples, Karol Postawa, Wojciech M. Budzianowski

Wojciech Budzianowski

This article describes methods of the determination of kinetic parameters from the thermogravimetric data set of biomass samples. It presents the methodology of the research, description of the needed equipment, and the method of analysis of thermogravimetric data. It describes both methodology of obtaining quantitative data such as kinetic parameters as well as of obtaining qualitative data like the composition of biomass. The study is focused mainly on plant biomass because it is easy in harvesting and preparation. Methodology is shown on the sample containing corn stover which is subsequently pyrolysed. The investigated sample show the kinetic of first order …

Temperature-Dependent Absorption Cross-Section Measurements Of 1-Butene (1-C4h8) In Vuv And Ir, Et-Touhami Es-Sebbar, Yves Benilan, Aamir Farooq

Dr. Et-touhami Es-sebbar

Vacuum ultraviolet (VUV) and infrared (IR) absorption cross-section measurements of 1-butene (1-C4H8; CH2=CHCH2CH3; Butylene) are reported over the temperature range of 296–529 K. The VUV measurements are performed between 115 and 205 nm using synchrotron radiation as a tunable VUV light source. Fourier Transform Infrared (FTIR) spectroscopy is employed to measure absorption cross-section and band strengths in the IR region between 1.54 and 25 μm (∼6500–400 cm−1). The measured room-temperature VUV and IR absorption cross-sections are compared with available literature data and are found to be in good agreement. The oscillator strength for the electronic transition (A1A′→X1A′) around 150–205 nm …

تمرين سري اول, Dr Alireza Zolfaghari

Dr Alireza Zolfaghari

No abstract provided.

Capacitively Coupled Radio-Frequency Discharges In Nitrogen At Low Pressures, L. L Alves, L. Marques, C. D Pintassilgo, W. Wattieaux, Et. Es-Sebbar, J. Berndt, E. Kovačević, N. Carrasco, L. Boufendi, G. Cernogora

Dr. Et-touhami Es-sebbar

This paper uses experiments and modelling to study capacitively coupled radio-frequency (rf) discharges in pure nitrogen, at 13.56 MHz frequency, 0.1–1 mbar pressures and 2–30 W coupled powers. Experiments performed on two similar (not twin) setups, existing in the LATMOS and the GREMI laboratories, include electrical and optical emission spectroscopy (OES) measurements. Electrical measurements give the rf-applied and the direct-current-self-bias voltages, the effective power coupled to the plasma and the average electron density. OES diagnostics measure the intensities of radiative transitions with the nitrogen second-positive and first-negative systems, and with the 811.5 nm atomic line of argon (present as an …

Ionization Photophysics And Rydberg Spectroscopy Of Diacetylene, M. Schwell, Y. Benilan, N.. Fray, M.-C. Gazeau, Et. Es-Sebbar, F.-G. Levrel, N. Campion, S. Leach

Dr. Et-touhami Es-sebbar

Photoionization of diacetylene was studied using synchrotron radiation over the range 8–24 eV, with photoelectron-photoion coincidence (PEPICO) and threshold photoelectron–photoion coincidence (TPEPICO) techniques. Mass spectra, ion yields, total and partial ionization cross-sections were measured. The adiabatic ionization energy of diacetylene was determined as IEad = (10.17 ± 0.01) eV, and the appearance energy of the principal fragment ion C4H+ as AE = (16.15 ± 0.03) eV. Calculated appearance energies of other fragment ions were used to infer aspects of dissociation pathways forming the weaker fragment ions , C3H+, and C2H+. Structured autoionization features observed in the PEPICO spectrum of diacetylene …

Volatile Products Controlling Titan’S Tholins Production, N. Carrasco, T. Gautier, Et. Es-Sebbar, P. Pernot, G. Cernogora

Dr. Et-touhami Es-sebbar

A quantitative agreement between nitrile relative abundances and Titan’s atmospheric composition was recently shown with a reactor simulating the global chemistry occurring in Titan’s atmosphere [Gautier et al. (2011) Icarus, 213: 625]. Here we present a complementary study on the same reactor using an in-situ diagnostic of the gas phase composition. Various initial N2-CH4 gas mixtures (methane varying from 1 to 10%) are studied, with a monitoring of the methane consumption and of the stable gas neutrals by in-situ mass spectrometry. Atomic hydrogen is also measured by optical emission spectroscopy. A positive correlation is found between atomic hydrogen abundance and …

Vuv Photoionization Of Acetamide Studied By Electron / Ion Coincidence Spectroscopy In The 8-24 Ev Photon Energy Range, M. Schwell, Y. Bénilan, N. Fray, M.-C Gazeau, Et. Es-Sebbar, Gustavo A. Garcia, L. Nahon, N. Champion, S. Leach

Dr. Et-touhami Es-sebbar

A VUV photoionization study of acetamide was carried out over the 8-24 eV photon energy range using synchrotron radiation and photoelectron/photoion coincidence (PEPICO) spectroscopy. Threshold photoelectron photoion coincidence (TPEPICO) measurements were also made. Photoion yield curves and branching ratios were measured for the parent ion and six fragment ions. The adiabatic ionization energy of acetamide was determined as I.E (12A’) = (9.71±0.02) eV, in agreement with an earlier reported photoionization mass spectrometry (PIMS) value. The adiabatic energy of the first excited state of the ion, 12A”, was determined to be ≈ 10.1 eV. Assignments of the fragment ions and the …

Hydrogen Production From Biogas By Oxy-Reforming: Reaction System Analysis, Aleksandra Terlecka, Wojciech M. Budzianowski

Wojciech Budzianowski

Oxy-reforming is emerging as an interesting alternative to conventional methods of hydrogen generation. The current article characterises this process through analysis of individual reactions: SMR (steam methane reforming), WGS (water gas shift) and CPO (catalytic partial oxidation). Analyses relate to optimisation of thermal conditions thus enabling cost-effectivenes of the process.

الگو و دستورالعمل تهيه و تنظيم پايان نامه کارشناسي, Dr Alireza Zolfaghari

Dr Alireza Zolfaghari

No abstract provided.