Mechanical Engineering Commons^™

Residual Stress Generation In Additive Manufacturing Of Complex Lattice Geometries, Katie Bruggeman, Nathan Klingbeil, Anthony N. Palazotto

Faculty Publications

Residual stresses developed during additive manufacturing (AM) can influence the mechanical performance of structural components in their intended applications. In this study, thermomechanical residual stress simulations of the laser powder bed fusion (LPBF) process are conducted for both simplified (plate and cube-shaped) geometries as well as five complex lattice geometries fabricated with Inconel 718. These simulations are conducted with the commercial software package Simufact Additive©, which uses a nonlinear finite element analysis and layer-by-layer averaging approach in determining residual stresses. To verify the efficacy of the Simufact Additive© simulations, numerical results for the plate and cube-shape geometries are analyzed for …

Ultrasonic Non-Destructive Evaluation Of Additively Manufactured Polymer-Ceramic Composites, Christian Alexander Ruiz

Open Access Theses & Dissertations

Digital light processing (DLP) is an attractive additive manufacturing technique due to its ability to create ceramic parts with complex geometries. DLP uses ultraviolet light to polymerize a slurry comprised of ceramic powder and photosensitive resin in layers to create solid parts. Printing parameters such as light intensity and exposure time are critical when producing these parts. Improper parameters can lead to over or under-curing, adversely impacting print quality and strength. Samples were printed at varying layer exposure times and then tested using ultrasonics to determine the degree of conversion. Additionally, ultrasonics were used as a non-destructive technique to obtain …

Heterogeneous Sensor Data Fusion For Multiscale, Shape Agnostic Flaw Detection In Laser Powder Bed Fusion Additive Manufacturing, Benjamin Bevans, Christopher Barrett, Thomas Spears, Aniruddha Gaikwad, Alex Riensche, Harold (Scott) Halliday, Prahalada Rao

Department of Mechanical and Materials Engineering: Faculty Publications

We developed and applied a novel approach for shape agnostic detection of multiscale flaws in laser powder bed fusion (LPBF) additive manufacturing using heterogenous in-situ sensor data. Flaws in LPBF range from porosity at the micro-scale (< 100 μm), layer related inconsistencies at the meso-scale (100 μm to 1 mm) and geometry-related flaws at the macroscale (> 1 mm). Existing data-driven models are primarily focused on detecting a specific type of LPBF flaw using signals from one type of sensor. Such approaches, which are trained on data from simple cuboid and cylindrical-shaped coupons, have met limited success when used for detecting multiscale flaws in complex LPBF parts. The objective of this work is to develop a heterogenous sensor data fusion …

Additive Manufacturing Of Aluminum Alloy By Metal Fused Filament Fabrication (Mf3)., Luke J. Malone

Electronic Theses and Dissertations

This research studies metal-fused filament fabrication (MF3) for manufacturing aluminum alloy parts. An aluminum alloy powder-based feedstock with a polymer-binder system was extruded via capillary rheometry to form a filament. The filament was used to print green parts that were involved in a two-step debinding process combining solvent and thermal extraction of the polymer binder, then sintered in a partial vacuum. Resulting grain structure, sintered density, and mechanical properties will be characterized and compared to metal injection molded (MIM) specimens. The main objective is to gain an understanding of the MF3 process characteristics and the ensuing material properties and microstructure …

Additive Manufacturing Of Variable Contrast Computed Tomography Anatomical Phantoms Using A Single Feedstock In Fused Filament Fabrication, Cory J. Darling

University of New Orleans Theses and Dissertations

Anatomical phantoms used in biomedical education and training benefit greatly from Fused filament fabrication’s (FFF) ability to rapidly produce complex and unique models. Current materials and methods used in FFF have limited ability to accurately produce phantoms that can mimic the radiological properties of multiple biological tissues. This research demonstrates that the CT contrast of FFF produced models can be modified by varying the concentration of bismuth oxide in acrylonitrile butadiene styrene (ABS) filaments and a tunable CT contrast that mimics the CT contrast ranging from fatty tissue to cortical bone using a single composite filament without introducing artificial image …

Computational Based Investigation Of Lattice Cell Optimization Under Uniaxial Compression Load, Derek G. Spear, Jeremiah S. Lane, Anthony N. Palazotto, Ryan A. Kemnitz

Faculty Publications

Structural optimization is a methodology used to generate novel structures within a design space by finding a maximum or minimum point within a set of constraints. Topology optimization, as a subset of structural optimization, is often used as a means for light-weighting a structure while maintaining mechanical performance. This article presents the mathematical basis for topology optimization, focused primarily on the Bi-directional Evolutionary Structural Optimization (BESO) and Solid Isotropic Material with Penalization (SIMP) methodologies, then applying the SIMP methodology to a case study of additively manufactured lattice cells. Three lattice designs were used: the Diamond, I-WP, and Primitive cells. These …

Structural Stability Of Thermosets During Material Extrusion Additive Manufacturing, Stian K. Romberg

Doctoral Dissertations

Over the past decade, the scale of polymer additive manufacturing has been revolutionized with machines that print massive thermoplastic parts with greater geometric complexity than can be achieved by traditional manufacturing methods. However, the heat required to print thermoplastics consumes energy and induces thermal gradients that can reduce manufacturing flexibility and final mechanical properties. With the ability to be extruded at room temperature and excellent compatibility with fibers and fillers, thermoset resins show promise to decrease the energy consumption, expand the manufacturing flexibility, and broaden the material palette offered by large-scale polymer additive manufacturing. However, structural instability in the uncured …

Process-Structure-Property Relationships In 3d-Printed Epoxy Composites Produced Via Material Extrusion Additive Manufacturing, Nadim S. Hmeidat

Doctoral Dissertations

Extrusion-based additive manufacturing (AM) technologies, such as direct ink writing (DIW), offer unique opportunities to create composite materials and novel multi-material architectures that are not feasible using other AM technologies. DIW is a novel 3D-printing approach in which viscoelastic inks, with favorable rheological properties, are extruded through fine nozzles and patterned in a filament form at room temperature.

Recent developments in DIW of polymer composites have led to expanding the range of materials used for printing, as well as introducing novel deposition strategies to control filler orientation and create improved functional/structural composite materials. Despite these substantial advancements, the successful and …

Reducing Corrosion Of Additive Manufactured Magnesium Alloys By Interlayer Ultrasonic Peening, M. P. Sealy, R. Karunakaran, S. Ortgies, G. Madireddy, A. P. Malshe, K. P. Rajurkar

Department of Mechanical and Materials Engineering: Faculty Publications

Additive manufad (AM) magn alloys corrode rapidly due to tensile stress and coarse microstructures. Cyclically combining (hybridizing) additive manufacturing with interlayer ultrasonic peening was proposed as a solution to improve corrosion resistance of additive manufactured magnesium WE43 alloy through strengthening mechanisms and compressive residual stress. Applying interlayer peening work hardened discrete layers and formed a glocal integrity of regional grain refinement and subsurface compressive residual stress barriers. Tensile residual stress that typically accelerates corrosion decreased 90%. Results showed time-resolved control over corrosion was attainable by interlayer peening, and local corrosion within print cells decreased 57% with respect to as-printed WE43.

Recurrence Network Analysis Of Design-Quality Interactions In Additive Manufacturing, Ruimin Chen, Prahalada K. Rao, Yan Lu, Edward W. Reutzel, Hui Yang

Department of Mechanical and Materials Engineering: Faculty Publications

Powder bed fusion (PBF) additive manufacturing (AM) provides a great level of flexibility in the design-driven build of metal products. However, the more complex the design, the more difficult it becomes to control the quality of AM builds. The quality challenge persistently hampers the widespread application of AM technology. Advanced imaging (e.g., X-ray computed tomography scans and high-resolution optical images) has been increasingly explored to enhance the visibility of information and improve the AM quality control. Realizing the full potential of imaging data depends on the advent of information processing methodologies for the analysis of design-quality interactions. This paper presents …

Process-Structure Relationship In The Directed Energy Deposition Of Cobalt-Chromium Alloy (Stellite 21) Coatings, Ziyad M. Smoqi, Joshua Toddy, Harold (Scott) Halliday, Jeffrey E. Shield, Prahalada K. Rao

Department of Mechanical and Materials Engineering: Faculty Publications

In this work, we accomplished the crack-free directed energy deposition (DED) of a multi-layer Cobalt- Chromium alloy coating (Stellite 21) on Inconel 718 substrate. Stellite alloys are used as coating materials given their resistance to wear, corrosion, and high temperature. The main challenge in DED of Stellite coatings is the proclivity for crack formation during printing. The objective of this work is to characterize the effect of the input energy density and localized laser-based preheating on the characteristics of the deposited coating, namely, crack formation, microstructural evolution, dilution of the coating composition due to diffusion of iron and nickel from …

Quality Assurance Of Lightweight Structures Via Phase-Based Motion Estimation, Ikenna E. Ifekaonwu

Electronic Theses and Dissertations

In recent years, lightweight structures have become mature and adopted in various applications. The importance of quality assurance cannot be overemphasized hence extensive research has been conducted to assess the quality of lightweight structures. This study investigates a novel process that exploits motion magnification to investigate the damage characteristics of lightweight mission-critical parts. The goal is to assure the structural integrity of 3D printed structures and composite structures by determining the inherent defects present in the part by exploiting their vibration characteristics. The minuscule vibration of the structure was recorded with the aid of a high-speed digital camera, and the …

Open-Source Digitally Replicable Lab-Grade Scales, Benjamin R. Hubbard, Joshua M. Pearce

Michigan Tech Publications

This study provides designs for a low-cost, easily replicable open-source lab-grade digital scale that can be used as a precision balance. The design is such that it can be manufactured for use in most labs throughout the world with open-source RepRap-class material extrusion-based 3-D printers for the mechanical components and readily available open-source electronics including the Arduino Nano. Several versions of the design were fabricated and tested for precision and accuracy for a range of load cells. The results showed the open-source scale was found to be repeatable within 0.05 g with multiple load cells, with even better precision (0.005 …

Additive Manufacturing Of Magnesium Alloys, Rakeshkumar Karunakaran, Sam Ortgies, Ali Tamayol, Florin Bobaru, Michael P. Sealy

Department of Mechanical and Materials Engineering: Faculty Publications

Magnesium alloys are a promising new class of degradable biomaterials that have a similar stiffness to bone, which minimizes the harmful effects of stress shielding. Use of biodegradable magnesium implants eliminates the need for a second surgery for repair or removal. There is a growing interest to capitalize on additive manufacturing's unique design capabilities to advance the frontiers of medicine. However, magnesium alloys are difficult to 3D print due to the high chemical reactivity that poses a combustion risk. Furthermore, the low vaporization temperature of magnesium and common biocompatible alloying elements further increases the difficulty to print fully dense structures …

Modeling Thermal And Mechanical Cancellation Of Residual Stress From Hybrid Additive Manufacturing By Laser Peening, Guru Madireddy, Chao Li, Jingfu Liu, Michael P. Sealy

Department of Mechanical and Materials Engineering: Faculty Publications

Additive manufacturing (AM) of metals often results in parts with unfavorable mechanical properties. Laser peening (LP) is a high strain rate mechanical surface treatment that hammers a workpiece and induces favorable mechanical properties. Peening strain hardens a surface and imparts compressive residual stresses improving the mechanical properties of a material. This work investigates the role of LP on layer-by-layer processing of 3D printed metals using finite element analysis. The objective is to understand temporal and spatial residual stress development after thermal and mechanical cancellation caused by cyclically coupling printing and peening. Results indicate layer peening frequency is a critical process …

Glocal Integrity In 420 Stainless Steel By Asynchronous Laser Processing, Michael P. Sealy, Haitham Hadidi, Cody Kanger, X. L. Yan, Bai Cui, J. A. Mcgeough

Department of Mechanical and Materials Engineering: Faculty Publications

Cold working individual layers during additive manufacturing (AM) by mechanical surface treatments, such as peening, effectively “prints” an aggregate surface integrity that is referred to as a glocal (i.e., local with global implications) integrity. Printing a complex, pre-designed glocal integrity throughout the build volume is a feasible approach to improve functional performance while mitigating distortion. However, coupling peening with AM introduces new manufacturing challenges, namely thermal cancellation, whereby heat relaxes favorable residual stresses and work hardening when printing on a peened layer. Thus, this work investigates glocal integrity formation from cyclically coupling LENS® with laser peening on 420 stainless steel.

Modeling And Validations Of Control Parameters For Material Extrusion-Based Additive Manufacturing Of Thixotropic Aluminum Alloys., Lars Herhold

Electronic Theses and Dissertations

Additive Manufacturing (AM) with metals has been accomplished mainly through powder bed fusion processes. Initial experiments and simulations using Material Extrusion Additive Manufacturing (MEAM) have been performed by various researchers especially using low melting alloys. Recently Stratasys Inc. submitted a patent application for the use of their Material Extrusion technology also called Fused Deposition Modeling (FDM) where they describe the process using thixotropic semi-solid alloys. Currently this process using semi-solid, engineering type alloys such as A356 or THIXALLOY 540 aluminum have not been researched to evaluate the control parameters. This research combines the in-depth knowledge of applying thixotropic semi-solid aluminum …

Ultrasonic Nondestructive Evaluation Of Metal Additive Manufacturing., Venkata Karthik Nadimpalli

Electronic Theses and Dissertations

Metal Additive Manufacturing (AM) is increasingly being used to make functional components. One of the barriers for AM components to become mainstream is the difficulty to certify them. AM components can have widely different properties based on process parameters. Improving an AM processes requires an understanding of process-structure-property correlations, which can be gathered in-situ and post-process through nondestructive and destructive methods. In this study, two metal AM processes were studied, the first is Ultrasonic Additive Manufacturing (UAM) and the second is Laser Powder Bed Fusion (L-PBF). The typical problems with UAM components are inter-layer and inter-track defects. To improve the …

Characterization Of High-Purity Niobium Structures Fabricated Using The Electron Beam Melting Process, Cesar Adrian Terrazas

Open Access Theses & Dissertations

Additive Manufacturing (AM) refers to the varied set of technologies utilized for the fabrication of complex 3D components from digital data in a layer-by-layer fashion. The use of these technologies promises to revolutionize the manufacturing industry. The electron beam melting (EBM) process has been utilized for the fabrication of fully dense near-net-shape components from various metallic materials. This process, catalogued as a powder bed fusion technology, consists of the deposition of thin layers (50 - 120µm) of metallic powder particles which are fused by the use of a high energy electron beam and has been commercialized by Swedish company Arcam …

Fabrication Of A Nickel-Based Superalloy In Electron Beam Melting And Process Improvements Using Thermal Feedback From A Multi-Wavelength Pyrometer, Jonathan Minjares

Open Access Theses & Dissertations

The focus of this research was to fabricate parts composed of a nickel-based superalloy containing high levels of aluminum and titanium (NSAT) by using electron beam melting (EBM) additive manufacturing (AM) technology and utilizing thermal feedback from a multi-wavelength pyrometer to perform process improvements leading to near defect-free parts. EBM is an AM technology that utilizes metal powder to fabricate parts in layer-by-layer manner. A multi-wavelength pyrometer was implemented in an Arcam S12 (Arcam AB, Sweden) EBM system to observe and record surface temperatures throughout fabrication. Temperature data from the EBM system and the multi-wavelength pyrometer were graphed using MATLAB …

Process Study And Control Of Electron Beam Melting Technology Using Infrared Thermography, Jorge Mireles

Open Access Theses & Dissertations

An IR camera was installed in an Arcam A2 system (Arcam AB, Mölndal, Sweeden) and layer-by-layer image acquisition was achieved. The camera's capability to detect manufacturing defects was evaluated by implementing computer vision techniques using LabVIEW measurement and programming software (National Instruments, Austin, TX). Thermal maps acquired by the IR camera allowed layer-by-layer part temperature to be recorded. A core objective of this research was to study the impact of processing temperature on EBM-fabricated Ti-6Al-4V parts and achieve controlled mechanical properties. In this research, build variations were achieved by modifying parameters that change processing temperature from the standard processing temperature. …

Selective Laser Sintering; A Design Of Experiments, Philip David Hopkins, Victor Castillo Phd

STAR Program Research Presentations

Additive Manufacturing (AM), also commonly known as 3D Printing or Rapid Prototyping, is a method of manufacturing that provides for the ability to make intricate internal features and easily customizable parts. The concept is to break a Computer Aided Design (CAD) file into a series of thin layers that are sent to the machine and laid down one layer at a time. Just like any other form of processing, material properties can alter by undergoing this process. Manipulating various parameters of the AM process can allow for different properties to be achieved. For this reason, an in depth study will …