Mechanical Engineering Commons^™

Design, Modeling, Fabrication, And Testing Of A Multistage Micro Gas Compressor With Piezoelectric Unimorph Diaphragm And Passive Microvalves For Microcooling Applications, Shawn Thanhson Le

Doctoral Dissertations

This dissertation investigates the development of a multistage micro gas compressor utilizing multiple pump stages cascaded in series to increase the pressure rise with passive microvalves and piezoelectric unimorph diaphragms. This research was conducted through modeling, simulation, design, and fabrication of the microcompressor and its components. A single-stage and a two-stage microcompressor were developed to demonstrate and compare the performance and effectiveness of using a cascaded multistage design.

Steady fluid flow through static microvalves structure was studied to gain insight on its gas flow dynamics and characteristics. Transient analysis combined with the structure's interaction was investigated with an analytical model …

Concurrent Detection And Isolation Of Cellular And Molecular Biomarkers, Wanfeng Huang

Open Access Dissertations

Detection of cancer markers such as protein biomolecules and cancer cells in bodily fluids is of great importance in early diagnosis, prognosis as well as evaluation of therapy efficacy. Numerous devices have been developed for detecting either cellular or molecular targets, however there has not yet been a system that can simultaneously detect both cellular and molecular targets effectively. Molecule and cell-based assays are important because each type of target can tell a different story about the state of the disease and the two types of information can potentially be combined and/or compared for more accurate biological or clinical assessments. …

Laser Direct Written Silicon Nanowires For Electronic And Sensing Applications, Woongsik Nam

Open Access Dissertations

Silicon nanowires are promising building blocks for high-performance electronics and chemical/biological sensing devices due to their ultra-small body and high surface-to-volume ratios. However, the lack of the ability to assemble and position nanowires in a highly controlled manner still remains an obstacle to fully exploiting the substantial potential of nanowires. Here we demonstrate a one-step method to synthesize intrinsic and doped silicon nanowires for device applications. Sub-diffraction limited nanowires as thin as 60 nm are synthesized using laser direct writing in combination with chemical vapor deposition, which has the advantages of in-situ doping, catalyst-free growth, and precise control of position, …

Modeling The Impact Of Battery Degradation Within Lifecycle Cost Based Design Optimization Of Heavy-Duty Hybrid Electric Vehicles, Ashish P. Vora

Open Access Dissertations

The optimal design of hybrid electric vehicle (HEV) powertrains from a systems perspective is critical to realize the maximum benefits for a given application. This is particularly true in the heavy-duty vehicle space where the major challenges are: (i) greater emphasis on economic viability, (ii) reluctance to take on risk associated with new technologies, and (iii) numerous diverse applications that preclude a one-size-fits-all approach to hybrid-electric powertrain design. Past studies on HEV powertrain design have either ignored battery degradation, or failed to holistically capture its impact from a lifecycle cost perspective. The focus of this effort is the development of …

Mixed Mesh/Nodal Magnetic Equivalent Circuit Modeling Of A Six-Phase Claw-Pole Automotive Alternator, Daniel C. Horvath

Open Access Theses

Magnetic equivalent circuits (MECs) have been employed by many researchers to model the relationship between magnetic flux and current in electromagnetic systems such as electric machines, transformers and inductors [1] ,[2]. Magnetic circuits are analogous to electric circuits where voltage, current, resistance and conductance are the respective counterparts of magneto-motive force (MMF), magnetic flux, reluctance and permeance. The solution of MECs can be accomplished with the plethora of techniques developed for electrical circuit analysis. Specifically, mesh analysis, based on Kirchoff’s Voltage Law (KVL), and nodal analysis, based on Kirchoffs Current Law (KCL), are two very common solution techniques. Once an …

Capacity Optimization Of Battery-Generator Hybrid Power System: Toward Minimizing Maintenance Cost In Expeditionary Basecamp/Operational Energy Applications, Jude C. Onwuanumkpe

Open Access Theses

Low and transient load condition are known to have deleterious impact on the efficiency and health of diesel generators (DGs). Extensive operation under such loads reduces fuel consumption and energy conversion efficiency, and contribute to diesel engine degradation, damage, or catastrophic failure. Non-ideal loads are prevalent in expeditionary base camps that support contingency operations in austere environments or remote locations where grid electricity is either non-existent or inaccessible. The impact of such loads on DGs exacerbates already overburdened basecamp energy logistics requirements. There is a need, therefore, to eliminate or prevent the occurrence of non-ideal loads. Although advances in diesel …

Swelling-Etching Characterization Of Copper (I) Oxide - Pdms For The Development Of Micro/Nano - Particles Composite Mems Corrosion Sensor, Abdoul Kader Maiga

Graduate Theses and Dissertations

The primary objective for this thesis is to contribute to the understanding of the oxide removal process for a corrosion sensing device. The goal for designing such a device is for monitoring corrosion on metallic structures. The sensing material (6.35mm x 1mm discs) of the device is composed of copper (I) oxide particles mixed in some polydimethylsiloxane (PDMS). The PDMS, “housing,” is meant for controlling the oxidation rate through the sensing material. A solvent was used to facilitate the etchant diffusion through the PDMS matrix. Toluene and acetic acid were the ideal solvent and etchant, respectively, for carrying out the …

Text-Independent Speaker Identification Using Statistical Learning, Alli Ayoola Ojutiku

Graduate Theses and Dissertations

The proliferation of voice-activated devices and systems and over-the-phone bank transactions has made our daily affairs much easier in recent times. The ease that these systems offer also call for a need for them to be fail-safe against impersonators. Due to the sensitive information that might be shred on these systems, it is imperative that security be an utmost concern during the development stages. Vital systems like these should incorporate a functionality of discriminating between the actual speaker and impersonators. That functionality is the focus of this thesis.

Several methods have been proposed to be used to achieve this system …

Experimental Verification And Integration Of A Next Generation Smart Power Management System, Tavis Clemmer

Graduate Theses and Dissertations

With the increase in energy demand by the residential community in this country and the diminishing fossil fuel resources being used for electric energy production there is a need for a system to efficiently manage power within a residence. The Smart Green Power Node (SGPN) is a next generation energy management system that automates on-site energy production, storage, consumption, and grid usage to yield the most savings for both the utility and the consumer. Such a system automatically manages on-site distributed generation sources such as a PhotoVoltaic (PV) input and battery storage to curtail grid energy usage when the price …

Integration And Implementation Of High-Voltage Energy Storage Sub-System For A Parallel-Through-The-Road Plug-In Hybrid Electric Vehicle, Bilwa A. Jadhav

Open Access Theses

With research showing an alarming rate of increase in global warming and thus causing dangerous instabilities in the weather, a strong push has been initiated to reduce greenhouse gas emissions. Transportation being one of the top offenders in greenhouse gas emissions, has led the drive for improving the efficiency of the modern automobile. One of the current strategies for reducing the emissions produced by the transportation sector is hybrid vehicles powered from both a fuel such as gasoline, diesel, or hydrogen; and electricity. This merger has proven to be effective at decreasing harmful emissions including, carbon dioxide (CO 2 ) …

Scalable Autonomous Operations Of Unmanned Assets, Sunghun Jung

Open Access Dissertations

Although there have been great theoretical advances in the region of Unmanned Aerial Vehicle (UAV) autonomy, applications of those theories into real world are still hesitated due to unexpected disturbances. Most of UAVs which are currently used are mainly, strictly speaking, Remotely Piloted Vehicles (RPA) since most works related with the flight control, sensor data analysis, and decision makings are done by human operators. To increase the degree of autonomy, many researches are focused on developing Unmanned Autonomous Aerial Vehicle (UAAV) which can takeoff, fly to the interested area by avoiding unexpected obstacles, perform various missions with decision makings, come …

Modeling Tools For Conformal Orthotic Devices, Steven David Riddle

Open Access Theses

The purpose of this thesis is to advance the design of conformal orthotic devices through the development of two modeling tools to address knowledge gaps in the field.

The field of human orthotics has been continually troubled by identifying successful methods of harnessing devices to the body. Past orthotics have utilized a rigid framework with minimal degrees of freedom (DOFs) driven by hard actuators attached to the body at select anchor points. Many devices design the structure and anchor points such that they reduce the degrees of freedom of a targeted joint, limiting the user's mobility and often causing the …

Development Of Mems-Based Corrosion Sensor, Feng Pan

Graduate Theses and Dissertations

This research is to develop a MEMS-based corrosion sensor, which is used for monitoring uniform, galvanic corrosion occurring in infrastructures such as buildings, bridges. The corrosion sensor is made up of the composite of micro/nano metal particles with elastomers. The mechanism of corrosion sensor is based on the mass transport of corrosive species through the sensor matrix. When the metal particles in the matrix corrode, the electrical resistivity of the material increases due to increasing particle resistances or reduction of conducting pathways. The corrosion rate can be monitored by detecting the resistivity change in sensing elements. The life span of …

Computational Design Of The Electrical And Mechanical Performance Of Steerable Mems Antennas, Morgan Andrew Roddy

Graduate Theses and Dissertations

This thesis describes the origins, improvements, and variations of a broadband microwave antenna that can be beam-steered by a micro-electromechanical system (MEMS). The steerable MEMS antenna of this work was comprised of a planar antenna on top of a Silicon membrane. The membrane is etched to create a gimbal hinge structure and a platform which supported the antenna and gave it one or two degrees of freedom of rotation. The antennas presented were broadband and fed by a coplanar waveguide (CPW) transmission line which traversed the hinge structure. The antenna's orientation in space was designed to be changed through electrostatic …

Development Of Spray Cooling For High Heat Flux Electronics, Jeremy Scott Junghans

Graduate Theses and Dissertations

The thermal demands of modern day electronic systems require innovative thermal solutions. Spray cooling has proven to be able to cool heat fluxes orders of magnitude higher than traditional cooling methodologies. This work includes a comparison of spray cooling to standard thermal management methodologies. Key system parameters and considerations are discussed. The properties of available packaging materials and their effect on the reliability of a spray cooled system are presented. Parameters such as fluid temperature, droplet size, fluid velocity and flow rate all directly impact performance and are detailed in this work. Finally, results from of a wide range of …

Energy-Based Analysis Of Utility Scale Hybrid Power Systems, Kwame Agyenim-Boateng

UNLV Theses, Dissertations, Professional Papers, and Capstones

The promise of large-scale use of renewables such as wind and solar for supplying electrical power is tempered by the sources' transient behavior and the impact this would have on the operation of the grid. Among the methods cited for addressing some of those concerns are exploring the complementary nature of solar and wind power generation, and through the use of supplemental energy storage. While the technology for the latter has not been proven to be economical on a large scale at the present time, some assessments of what magnitude is required can be made. An energy-based analysis of utility …

A Study Of A Novel Modular Variable Geometry Frame Arranged As A Robotic Surface, Christopher James Salisbury

UNLV Theses, Dissertations, Professional Papers, and Capstones

The novel concept of a "variable geometry frame" is introduced and explored through a three-dimensional robotic surface which is devised and implemented using triangular modules. The link design is optimized using surplus motor dimensions as firm constraints, and round numbers for further arbitrary constraints. Each module is connected by a passive six-bar mechanism that mimics the constraints of a spherical joint at each triangle intersection. A three dimensional inkjet printer is used to create a six-module prototype designed around surplus stepper motors powered by an old computer power supply as a proof-of-concept example.

The finite element method is applied to …

Kinetics Of Laser Chemical Vapor Deposition Of Carbon And Refractory Metals, Feng Gao

Doctoral Dissertations

Three-dimensional laser chemical vapor deposition (3D-LCVD) has been used to grow rods of carbon, tungsten, titanium, and hafnium from a variety of hydrocarbons and metal halide-based precursors. A novel computerized 3D-LCVD system was designed and successfully used in the experiments. A focused Nd:Yag laser beam (λ = 1.06 μm) was utilized to locally heat up a substrate to deposition temperature. The rods, which grew along the axis of the laser beam, had a typical diameter of 30–80 μm and a length of about 1 mm. The precursors for carbon deposition were the alkynes: propyne, butyne, pentyne, hexyne, and octyne. Propyne …

The Optimized Electrostatic Motor, Christopher Lee Rambin

Doctoral Dissertations

The most common means of electrically activated actuation is the electromagnetic motor. All electromagnetic motors have a low output to weight ratio and low energy efficiency. The motor's weight is due to the coils and magnets used to generate propulsion. The energy loss is mainly the result of Joule heating that is inherent with any current driven device. An electrostatic motor offers the potential of significantly less weight and higher energy efficiency. This lower weight characteristic is due to the epoxide material used to construct the major components of its propulsion unit. Greater efficiency results from the reduced Joule heating …