Mechanical Engineering Commons^™

Impact Force Helmet Device For Concussion Monitoring, Patrice Mulligan, Karina Mealey, Zack Borthwick, Benjamin Fick

General Engineering

To track head trauma in football, our device is placed inside a football helmet to measure both linear and gyroscopic (rotational) accelerations. These measurements are taken using an ADXL375 linear accelerometer and an LSM6DSOX accelerometer and gyroscope. The data from these sensors is processed and transmitted wirelessly by a SparkFun Thing Plus microcontroller to another SparkFun Thing Plus microcontroller connected to a laptop on the sidelines. Our program on the laptop stores the acceleration impact data into a .csv file for each player. If a likely concussive impact is detected, the program displays a popup warning. Testing results were promising …

Programmable Vibration Table Retrofit With Eagle Medical, Jonathan Ilagan, Madhav Asok, Max Lewter

Biomedical Engineering

This project aimed to repair and upgrade a vibration table used for package testing for the sponsor, Eagle Medical - a medical packaging and sterilization company based in Paso Robles, California. The current vibration table is not programmable and lacks circuit diagrams, making it difficult to repair. In addition, it is not functional due to internal circuitry issues and power requirements. To address these issues, the team will implement several upgrades to improve the product and allow for better random cyclic vibration testing. A full assessment of the existing vibration table will be conducted to ensure the viability of these …

Power Thyristor Controller For Speed Control Of Dc Motor, Alejandra Zapata, Morgan Erich Boehme, Abdullah Mohammed Awidah, Payton Robert Chalstrom

Electrical Engineering

In this work, a Power Thyristor Controller for Speed Control of DC Motor has been developed with the purpose of replacing an existing simulation experiment, aiming to effectively implement the principle of learning by doing. The primary objective of the experiment setup is to illustrate the fundamental principles and operational mechanisms underlying the firing angle and controlled bridge rectifier. The new experiment is taking advantage of the existing FCRO4100 Single Phase Firing Board that was donated to the University by ENERPRO. The pre-programmed microcontroller is connected to the thyristor bridge rectifier that’s powered by 24VAC. Additionally, a DC motor will …

Sky Survey Radio Telescope, Jack E. Mcguigan

Electrical Engineering

This document outlines the design of a radio telescope designed to perform hydrogen line sky surveys. The telescope produces radio images mapping the intensity and relative velocities of hydrogen concentrations to their sky coordinates. Over the course of a day, the telescope images the regions of space visible to it, allowing sky survey imagery to be updated daily. Sky survey images are comprised of an array of pixels corresponding to specific sky coordinates. Each 8-bit RGB pixel contains information on the concentrations of hydrogen in the brightness and relative velocity in the color. Radio images mapping the concentrations and velocities …

Hypoxic Incubation Chamber, Simone Lisette Helfrich, Makenzie Nicole Jones

Biomedical Engineering: Graduate Reports and Projects

This paper describes the design, manufacturing, and testing of a novel controllable hypoxic incubator with fully functional oxygen gas control and temperature control in a humid environment. On the current market, a majority of the few hypoxic incubators use pre-mixed gas that does not offer precise control over gas concentration. The objective for this project was to create a chamber that allows the user to set the O2 concentration to varying set points of % O2 while maintaining the chamber at a constant body temperature, CO2 level, humidity, and sterility. To start the project, multiple concepts were developed for the …

Hypoxic Incubation Chamber, Simone Lisette Helfrich, Makenzie Nicole Jones

Master's Theses

This paper describes the design, manufacturing, and testing of a novel controllable hypoxic incubator with fully functional oxygen gas control and temperature control in a humid environment. On the current market, a majority of the few hypoxic incubators use pre-mixed gas that does not offer precise control over gas concentration. The objective for this project was to create a chamber that allows the user to set the O2 concentration to varying set points of % O2 while maintaining the chamber at a constant body temperature, CO2 level, humidity, and sterility. To start the project, multiple concepts were developed for the …

Developing A Miniature Smart Boat For Marine Research, Michael Isaac Eirinberg

Computer Engineering

This project examines the development of a smart boat which could serve as a possible marine research apparatus. The smart boat consists of a miniature vessel containing a low-cost microcontroller to live stream a camera feed, GPS telemetry, and compass data through its own WiFi access point. The smart boat also has the potential for autonomous navigation. My project captivated the interest of several members of California Polytechnic State University, San Luis Obispo’s (Cal Poly SLO) Marine Science Department faculty, who proposed a variety of fascinating and valuable smart boat applications.

Multifamily Complex Smart Locks For Property Management And Tenant Security, April Mills, Allen Chen, Dana Kumamoto, Michael Cook

Mechanical Engineering

Maintaining and managing hundreds of locks and physical keys for an apartment complex can be time consuming and costly, especially when the apartments turn over to new tenants. Our goal was to develop a smart door lock that is compatible with Obodo’s management app for apartment complexes to make accessing apartments secure and simpler for tenants and easier to manage for owners.

We designed and manufactured one smart door lock that is powered with four AA batteries and utilizes a dynamic NFC device and Bluetooth technology. The board can enter a sleep mode which reduces power consumption. The dynamic NFC …

Barker Bird Animatronic Senior Project Report, Marcus Monroe, Nolan Clapp, Ishan Jandaur, Jonathan Ogden

Mechanical Engineering

This document describes how our F71 Senior Design Project team developed a 3D printed, electronic bird that mimics Disneyland’s first animatronic, the Barker Bird. An animatronic is a mechanical puppet that replicates real life movement with robotic parts. Disney’s Barker Bird is a well-known animatronic that replicates a talking macaw with multiple moving systems. The final prototype completed by our team serves as a teaching tool for CAPED (Cal Poly Amusement Park Engineers and Designers) club members that are interested in the field of animated robots.

Sunsation’S Solar Powered Picnic Table, Michelle M. Barnett, Christopher Barber, Casey Durham, David Mason

Mechanical Engineering

Team SunSation is an interdisciplinary senior design project group that was tasked with developing a semi-permanent seating area for Cal Poly's electrical engineering courtyard. The EE courtyard is populated with plastic folding tables and chairs that are slowly falling apart. Dale Dolan, the head of the EE department, requested that a table design be developed that incorporates the use of solar panels. The addition of the solar panels to the table would help promote clean renewable energy as well as provide shade to those sitting in the courtyard.

The solution that SunSation arrived at is broken up into mechanical/structural, electrical, …

8 Dof Quadrupedal Hopping Robot, Clayton T. Elwell, John Bennett, Tyler Mccue, Daniel Munic

Mechanical Engineering

The goal of our senior project was to fabricate an eight degree of freedom (DOF) prototypical quadrupedal robot, develop a controller than commands the quadruped to repeatedly jump 10 cm in the air, and fabricate a modular test stand to safely deploy our controller on the quadruped. The creation of a functional quadruped will bring attention to Dr. Siyuan Xing and Charlie Refvem’s research group, Cal Poly Legged Robots, and will give future Cal Poly undergraduate and graduate students a learning tool to explore dynamic control of biomimetic robotic systems.

Over the course of our senior project, we successfully manufactured …

Total Sky Imager Project, Ryan D. Maier, Benjamin Jack Forest, Kyle X. Mcgrath

Mechanical Engineering

Solar farms like the Gold Tree Solar Farm at Cal Poly San Luis Obispo have difficulty delivering a consistent level of power output. Cloudy days can trigger a significant drop in the utility of a farm’s solar panels, and an unexpected loss of power from the farm could potentially unbalance the electrical grid. Being able to predict these power output drops in advance could provide valuable time to prepare a grid and keep it stable. Furthermore, with modern data analysis methods such as machine learning, these predictions are becoming more and more accurate – given a sufficient data set. The …

Solar Solution For Mini-Rover, Michaella Ochotorena, Derick Louie, Jonathan Cederquist, Collin Petersen, Cole Korchek

Mechanical Engineering

This project focuses on designing, building, and testing a functional prototype of a collapsible solar array on the mini Mars rover being developed by client and sponsor, Mr. Rich Murray. Although many previous collapsible solar arrays have been deployed for space missions, the previous solar-powered Mars rovers only deployed their arrays once upon landing. This solar array will be able to collapse and deploy multiple times to allow for greater rover mobility and stability when the rover is not charging. This system is critical to the success of the rover project because it provides power without which the rover cannot …

Bike To The Future, Wanjiku Gichigi, Luisa Shu Yi Chiu, Alexander Kalman Dunn, Georgia Ann Holmes

Mechanical Engineering

Brian Higgins is a veteran with retinitis pigmentosa who enjoys biking. The motivation for this project was to design and manufacture a refined prototype of a bike attachment to assist Brian in safely biking to and from work. The customer needs, problem definition, background, design development, final design, testing, costs, and recommendations are provided in this report.

The solution for this project, as laid out in the design development section, was to design an assembly that would detect objects in the biker’s path and relays that information to them. The design incorporated a dashboard to conceal components within, protect them …

Baker/Koob Final Report: Solar Solution For Mini Mars Rover, Jonathan Cederquist, Cole Korchek, Derick Louie, Michaella Ochotorena, Collin Petersen

Mechanical Engineering

This project focused on designing, building, and testing a functional prototype of a collapsible solar array on the mini Mars rover being developed by client and sponsor, Mr. Rich Murray. Although many previous collapsible solar arrays have been deployed for space missions, the previous solar-powered Mars rovers only deployed their arrays once upon landing. This solar array will be able to collapse and deploy multiple times to allow for greater rover mobility and stability when the rover is not charging. This system is critical to the success of the rover project because it provides power without which the rover cannot …

Model-Based Design Of An Optimal Lqg Regulator For A Piezoelectric Actuated Smart Structure Using A High-Precision Laser Interferometry Measurement System, Grant P. Gallagher

Master's Theses

Smart structure control systems commonly use piezoceramic sensors or accelerometers as vibration measurement devices. These measurement devices often produce noisy and/or low-precision signals, which makes it difficult to measure small-amplitude vibrations. Laser interferometry devices pose as an alternative high-precision position measurement method, capable of nanometer-scale resolution. The aim of this research is to utilize a model-based design approach to develop and implement a real-time Linear Quadratic Gaussian (LQG) regulator for a piezoelectric actuated smart structure using a high-precision laser interferometry measurement system to suppress the excitation of vibratory modes.

The analytical model of the smart structure is derived using the …

Performance Loss Rate And Temperature Modeling In Predictive Energy Yield Programs For Utility-Scale Solar Power Plants, Katelynn M. Dinius

Master's Theses

The Gold Tree Solar Farm, designed by REC Solar, has a rated output power of 4.5 MW and began operation in 2018 to provide electricity to Cal Poly’s campus. Gold Tree Solar Farm site terrain consists of rolling hills and uneven slopes. The uneven typography results in interrow shading, requiring a modified tracking control algorithm to maximize power production. Predicting a utility solar field’s lifetime energy yield is a critical step in assessing project feasibility and calculating project revenue. The MATLAB-based predictive power model developed for this field overpredicted power in the middle of the day. The purpose of this …

Field Testing The Effects Of Low Reynolds Number On The Power Performance Of The Cal Poly Wind Power Research Center Small Wind Turbine, John B. Cunningham

Master's Theses

This thesis report investigates the effects of low Reynolds number on the power performance of a 3.74 m diameter horizontal axis wind turbine. The small wind turbine was field tested at the Cal Poly Wind Power Research Center to acquire its coefficient of performance, C­_p, vs. tip speed ratio, λ, characteristics. A description of both the wind turbine and test setup are provided. Data filtration and processing techniques were developed to ensure a valid method to analyze and characterize wind power measurements taken in a highly variable environment. The test results demonstrated a significant drop in the …

Reading Robot, Gillian Watts, Andrew Myers, Sabrinna Tan, Taylor Klein, Omeed Djassemi

General Engineering

Presently, there is an insufficient availability of human experts to assist students in reading competency and comprehension. Our team’s goal was to create an improved socially assistive robot for use by therapists, teachers, and parents to help children and adults develop reading skills while they do not have access to specialists. HAPI is a socially assistive robot that we created with the goal of helping students practice their reading comprehension skills. HAPI enables a student to improve their reading skills without an educator present, while enabling educators to review the student's performance remotely. Design constraints included: physical size, weight, duration …

Raysun's Infrared Raisin Dryer, Lucas Kensinger, Saraith Aispuro, Joe Vanacore

General Engineering

The RaySuns senior project team was tasked with lowering the drying costs of raisins for River Ranch Raisins. In doing so, we explored several options for cutting costs: utilizing automation and exploring new drying technologies were our primary focus. We eventually planned a modular infrared heating mechanism which would be easy to automate in future projects. After manufacturing and testing an infrared heating mechanism, it was found that infrared drying could significantly cut costs versus the previous natural gas fired dryer tunnels while leaving room for automation. The infrared dryer was also shown to have the potential to create high-quality …

Automated Drone Calibration System, Jackie Kelly Jong-Mee Paik, Zach Nathan Richter, Tyler Wilson Van Den Berg, Ryan Alexander Zhan, Matthew Ward Carlson

Mechanical Engineering

The final design review of the Inspired Flight Calibration Team senior project will detail the process used to complete a verification prototype of a drone calibration device and discuss lessons learned and suggestions for improving this device. Going from brainstorming and conceptual prototyping all the way through verification prototyping and testing, we were able to design a gyroscopic device that met Inspired Flight’s needs for the flight sensor calibration of their drones. The mechanical design involved comprehensive CAD models and hands-on manufacturing. The mechatronics side of the project worked heavily with electrical wiring and writing custom software to communicate and …

Design, Modeling And Control Of A Two-Wheel Balancing Robot Driven By Bldc Motors, Charles T. Refvem

Master's Theses

The focus of this document is on the design, modeling, and control of a self-balancing two wheel robot, hereafter referred to as the balance bot, driven by independent brushless DC (BLDC) motors. The balance bot frame is composed of stacked layers allowing a lightweight, modular, and rigid mechanical design. The robot is actuated by a pair of brushless DC motors equipped with Hall effect sensors and encoders allowing determination of the angle and angular velocity of each wheel. Absolute orientation measurement is accomplished using a full 9-axis IMU consisting of a 3-axis gyroscope, a 3-axis accelerometer, and a 3-axis magnetometer. …

Critical Radius Of Insulation, Maria N. Ambrose, Samuel J. Sayre, Travis W. Martin, Matt T. Sterling

Mechanical Engineering

The critical radius of insulation is a counterintuitive concept within the study of heat transfer. The theory states that adding insulation to a cylindrical or spherical object will increase the rate of heat loss rather than decrease it, if the radius (thickness) of the insulation is at its “critical” value. The Critical Radius of Insulation Senior Project is designed to demonstrate this phenomenon to Heat Transfer students via a portable apparatus. The concept will be demonstrated with a cylindrical object which is heated by way of a separate voltage source. Thermocouples will display the temperature of the cylinder while insulation …

Heat: Hydraulic And Electric Animation Team, Tyler J. Couvrette, Michael J. Cain, Sara T. Novell, Dexter K. Yanagisawa

Mechanical Engineering

Each New Years’ Day, the Cal Poly Rose Float presents a flower-covered float to the world at the Tournament of Roses parade. This floral display, paired with moving mechanical animations, shows off Cal Poly to the world. This project strove to keep Cal Poly on the cutting edge of technology both in parade floats, and in engineering, by creating a completely electric-powered animation system.

To accomplish this, a group of students set out to make the fully electric animation system that can power both the hydraulic and electric mechanisms on the Float. This was accomplished through months of planning and …

Danny’S Recumbent Bike Accessibility Device Final Design Report, Joseph J. Lee, Huy Nguyen, Jack Mcatee, John Kulick

Mechanical Engineering

The purpose of this document is to fully define our design solution and explain our manufacturing and testing results. Our project’s goal is to find a way to allow Danny Knutson, a retired Navy pilot and incomplete quadriplegic with limited use of his arms and an impaired sense of balance, to enter and exit his recumbent tricycle without any discomfort for him or his aide. We completed multiple interviews with Danny, patent research, existing product research, and other technical literature research in order to fully understand the problem. We synthesized this information to create a concrete list of customer wants …

Design Of A Low-Cost Data Acquisition System For Rotordynamic Data Collection, Gregory S. Pellegrino

Master's Theses

A data acquisition system (DAQ) was designed based on the use of a STM32 microcontroller. Its purpose is to provide a transparent and low-cost alternative to commercially available DAQs, providing educators a means to teach students about the process through which data are collected as well as the uses of collected data. The DAQ was designed to collect data from rotating machinery spinning at a speed up to 10,000 RPM and send this data to a computer through a USB 2.0 full-speed connection. Multitasking code was written for the DAQ to allow for data to be simultaneously collected and transferred …

Nanosatellite Launch Data-Logger (Sync), Christopher Martin Gerdom

Master's Theses

CubeSat designers are increasingly looking to incorporate delicate structures and optics into their payloads. These delicate payloads, however, may not survive the required absolute-worst-case launch vibration testing needed for flight certification. To help address this problem, and to better match testing conditions to real-world launch environments, this thesis introduces Sync, a compact 1/4U CubeSat payload designed to collect data on the vibrations and thermal environments CubeSats experience inside a deployer on the way to orbit. This data can be used to better understand the launch environment for different vehicles, and help develop new, more realistic testing guidelines that could enable …

Furnace System Improvements, Kenji K. Anzai, Ethan Fedor, Patrick Zailaa

Mechanical Engineering

This Final Design Review (FDR) documents the work done by the group to manufacture the system to deliver improvements to the furnace in the Cal Poly microfabrication laboratory (better known as the cleanroom). The document describes the material covered in the Scope of Work (SOW), including background research, customer needfinding, and the problem statement, material associated with concept development and selection for Preliminary Design Review (PDR), material detailing the design and manufacturing plan of the system for Critical Design Review (CDR), and new material detailing the manufacture of the system for FDR.

Research done for the SOW resulted in a …

Dynamics Simulation And Optimal Control Of A Multiple-Input And Multiple-Output Balancing Cube, Felix K. Haimerl

Master's Theses

This thesis document outlines the development of a multibody dynamics simulation of an actively stabilized multiple-input, multiple-output, coupled, balancing cube and the process of verifying the results by implementing the control algorithm in hardware. A non-linear simulation of the system was created in Simscape and used to develop a Linear Quadratic Gaussian control algorithm. To implement this algorithm in actual hardware, the system was first designed, manufactured, and assembled. The structure of the cube and the reaction wheels were milled from aluminum. DC brushless motors were installed into the mechanical system. In terms of electronics, a processor, orientation sensor, motor …

Farmbot Trackless Redesign, Cole Thomas, Cailey Kamm, Clayton Alderson, Otto Akerstrom

Industrial and Manufacturing Engineering

For this project the team PLANT3D worked along with Rory Aronson and FarmBot to generate a cheaper more user-friendly design for the FarmBot Genesis 1.3. Working with Rory and FarmBot, we as a team generated a list of design requirements and engineering specifications for the project. These requirements centered around creating a more accessible FarmBot model for the average person to be able to purchase and set up with ease. Much of this required taking the existing system and eliminating the most common problem areas. These were the track system, built using 1.5 meter aluminum extrusions and the complex interchangeable …