Mechanical Engineering Commons^™

Rc Baja: Drivetrain And Steering, Mathew Morgan

All Undergraduate Projects

The RC Baja competition is a contest where undergraduate mechanical engineering students design, build, and compete against one another. The objective of this competition is to create the most efficient RC car possible. A gear train analysis was done and showed an 8:1 gear ratio would be the most efficient ratio due to the chosen motor having a higher torque output. Also, a stress analysis was done and showed that 2011 T3 aluminum passed the stress and weight criteria. These analyses ensured the RC Baja car was efficient. Most of the parts for the drivetrain and steering subassemblies were machined …

R/C Baja: Drivetrain, Connor T. Donovan

All Undergraduate Projects

The Central Washington University Mechanical Engineering Technology Department hosts an annual R/C Baja competition in which R/C cars fabricated by student teams are put through a series of courses and tests to determine which team's vehicle is best. The goal of this project was to create a functioning drivetrain that conveys power from the battery to the wheels and provides control of the vehicle. A list of requirements for the drivetrain was created to ensure that the vehicle will not only function, but that it will actually succeed in the competition. These requirements included that the vehicle must achieve a …

Jcati Carbon Fiber Recycler: Oven Enclosure, Margarita Romero

All Undergraduate Projects

Central Washington University partners with Boeing and is funded by the Joint Center of Aerospace Technology Innovation (JCATI) to develop a mechanism that takes carbon fiber wing trimmings from Boeing that are resin coated and recycles carbon fiber. This is done by crushing the wing trimmings and then putting it into a 500°C oven to melt off the resin. This project focuses on the enclosure for the oven and making sure precautions are met such as having the outside surface be less than 45c through heat transfer analysis, argon fills enclosure in 13 minutes through fluid dynamics analysis, and 99% …

R/C Baja Truck Suspension, Chassis And Steering, Ryan Lafrombois

All Undergraduate Projects

The ASME RC Baja Challenge is an annual competition that the Central Washington University Mechanical Engineering and Technology (MET) department takes part in. Senior level engineers divided the work between the drivetrain and the chassis/suspension while designing and manufacturing to meet a set of requirements. Next, a device was to be developed to be able to withstand the extreme forces to be successful in the competition at the end of the year. The process would require that the students use their acquired knowledge and skills to design, manufacture, and analyze a capable device. Designing involved the completion of 12 analyses …

Rc Baja Engineering Report, Matthew Hart

All Undergraduate Projects

The ASME RC Baja is a competition that tests engineering students’ ability design, build, and test an RC car. The vehicle then competes against other engineering student’s RC cars. The objective is to manufacture the most efficient and cost-effective RC Baja car.

During the first quarter of senior project, the student’ engineering skill was applied to designing an RC car that will be able to compete in a competition at the end of spring quarter. The student was tasked with using all the information from the classes the student had taken previously at Central Washington University and design and build …

Carbon Fiber Recycling: Delamination System, Aaron Eastman

All Undergraduate Projects

The production of composite wings at Boeing causes carbon fiber waste and CWU Mechanical Engineering Technology students have been tasked in designing a carbon fiber recycling system. This project was brought forth and funded by the Joint Center for Aerospace Technology Innovation (JCATI). There are three subsystems that make up the carbon fiber recycling system, the delamination system, shredding system, and the oven. The purpose of this project was to increase the efficiency and effectiveness of the delamination system of the carbon fiber recycling system. The old system reached approximately 30-40 percent delamination with one pass through the system, and …

Asme Rc Baja Racer, Chesna Kern

All Undergraduate Projects

The American Society of Mechanical Engineers (ASME) holds a competition at their annual conference for college students to design an RC car that will compete in sprint, slalom, and obstacle course races. The RC Baja car was designed to complete every event in the competition with a focus on the obstacle course due to the anticipated impacts inflicted on the project car by jumps and other obstacles. The project was a collaborative effort. This presentation focuses on the chassis and suspension while Gizan Gando will present about the drivetrain. The drop and frontal impact test requirements guided the design process …

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …

Jcati Base Plate, Jacob Atamian

All Undergraduate Projects

Students of the Mechanical Engineering Technology (MET) program at Central Washington University have contributed to an ongoing Carbon Fiber Recycler project funded by the Joint Center for Aerospace Technology Innovation (JCATI). The goal of this project was to modify the existing recycling system to produce a higher success rate of recycled carbon composite material. This report focuses on increasing the rigidity of the crushing gears so that the deflection occurring among the components during operation was below 0.005 inches to ensure proper operating conditions. The operating speed of the crushing gears was 2.5 rpm with a crushing load of 10,500 …

Mini Rc Baja Car, Jason Schindler

All Undergraduate Projects

Incorporating each aspect of engineering incorporated into a senior project is difficult. That is why an RC Baja car is a great senior project for Mechanical Engineering students. The approach that students must take to design, construct, and test the car is to set parameters, and to make overall goals that can be easily measured. These goals include, but not limited to things like a $700 budget and the ability to withstand a 1-foot drop to a flat surface on all four wheels simultaneously. First, the design must meet the specifications and rules that are set previously. This ensures that …

Balsa Wood Bridge, Anndie Watterson

All Undergraduate Projects

A model for a strong bridge that could span a set distance and rise up to allow for passage underneath was requested, and specifications for the design were given. The model bridge was designed out of balsa wood to meet all the requirements. Using structural and material analysis and simple mechanical designs, a bridge was designed and constructed out of balsa wood, wood glue, and metal components used for articulation that met all of the criteria set by the assigner. The bridge was tested to ensure all specifications were met. The resulting bridge can hold 20kg of weight suspended from …

Asme Rc Baja Car Drivetrain, Gizan G. Gando

All Undergraduate Projects

The purpose of the RC Baja Car is to compete in the American Society of Mechanical Engineers (ASME) competition, a series of events to prove the functionality of the vehicle. This series of events includes the Slalom, Drag, and Baja race. The Slalom is a test in the steering capability of the car. The Drag is a test in the acceleration of the car in a straight line. Lastly, the Baja puts all factors together in a race to test every component of the car. This project is about building an RC car that can function under these conditions and …

Cubesat 5000, Renee Redman

All Undergraduate Projects

Cubesat 5000 is designed for the annual Physics weather balloon launch which is done for the senior level astrophysics students. Students use the weather balloons to get better visuals of the sun in the upper atmosphere. The purpose of the Cubesat 5000 design is to keep the instrumentation inside safe during and after the launch, maintain working temperature, and to remain below a 400-gram weight requirements in order to achieve optimum altitude.

The outer cube assembly was designed using Solidworks and printed using PETG filament. The weight of the cube has been measured and design changes were made done to …

R/C Mini Baja Car: Drive Train And Steering, Carlton R. Mcdonald

All Undergraduate Projects

The purpose of the Baja R/C Car is to compete in the ASME eFX competition in a series of events to prove the functionality of the vehicle. This series of events includes the Slalom, Drag, and Baja race, The Slalom is a test in the steering capability of the vehicle, the Drag is a test in the acceleration of the vehicle in a straight line, and the Baja puts all factors together in a race to test every component of the vehicle. This project is about building an R/C car that not only functions, but also has maximum performance capabilities …

Rc Mini Baja Car - Suspension And Chassis, Collin Mckenzie

All Undergraduate Projects

Two students have developed a unique design of the RC Baja Car to optimize functionality and performance. A Baja car is a remote controlled 1/10 scale car that is used for recreation or competition, usually meant for competing in the ASME Baja car competition versus various schools. The competition focuses on the best time achieved in different courses that utilize speed, turns, and jumps. The objective for the project was to create a unique suspension from previous individual’s projects by creating a four-link suspension in which allows more travel in the suspension of the car and maintains functionality with the …

Mechanical Footstep Power Generator, Mohammed Saleh Aljohani, Faisal Alonazi

All Undergraduate Projects

Mechanical Footstep Power generator

By Author: Mohammed Aljohani

Abstract

Modern technology is focusing on newer and better sources of energy. Among the important areas are power generation methods since electricity has become part of our lives. Various researchers have conducted surveys to find out the feasibility of converting renewable kinetic energy into electricity. Some of the works done in the past emphasized the selection of suitable materials and power generation systems designs that appear complicated and expensive. To ensure there is cost efficiency and energy efficiency better power generation systems need to be embraced.

The footstep power generator is a …

Stair Climbing Hand Truck, James Mcpherson

All Undergraduate Projects

Abstract

Getting a heavy object up a flight of stairs usually requires a team of two or more people. Even with a team of people, the task is often still difficult, dangerous, and possibly insurmountable by one person. This problem is especially prevalent in for those who are moving into apartment complexes. Most apartment complexes have many buildings with two or more floors of living quarters, and elevators are often missing. This project sought to offer a solution to this problem. The solution in question; a motorized hand-truck with 2, trigonal planar pinwheels in place of the stock wheels. The …

Custom Foot Prosthetic: Diabetic Care, Chandler Streuli

All Undergraduate Projects

Across the United States there are people every day who lose their toes to diabetes or to loss of circulation within their legs. The problem becomes building a more cost effective and efficient prosthetic for these individuals. The prosthetics that are used for medical purposes are often costly, especially without the help of insurance. The new prosthetic was designed to be taken in and out of shoes so that it is fast and easy for the user to move the device from shoe to shoe. The manufacturing method for this project was using a 3D printer to build the initial …

Autojack - Hydraulic Powertrain System, Tyce Vu

All Undergraduate Projects

A primary problem for mechanics and automotive enthusiasts is the risk associated with lifting and securing a vehicle with conventional jack stands. Often times, improper jack-stand installation results in the vehicle collapsing unexpectedly, causing injury and/or death. This problem can be minimized through the application of a newly re-designed vehicle lifting system. The conventional method for lifting cars is time consuming and can be unsafe in many circumstances. A better, safer, and more efficient lift design was needed; the AutoJack. The approach of the AutoJack design was entirely focused on the safety of lifting a vehicle. Safety was improved by …

Electrathon: Body, Ryan Shiner

All Undergraduate Projects

• The Electrathon Vehicle project is an ongoing project that dates back to 2012. This vehicle will be raced at events to see how many laps it can complete on a single battery charge. The existing body for the Central Washington University Electrathon vehicle required modifications to fit over the current frame. These modifications were required because the rear suspension design had changed. The rear panel of the body interfered with the rear suspension. Using a rotary cutting wheel, the panel was slotted so the body could slide over the suspension and drive chain. Additionally, spacers for various sizes were needed …

Composite Recycler: Frame, Alfonso Olivera

All Undergraduate Projects

How can composites be recycled? The Composite Recycler is an ongoing project that started in September 2017. The purpose of this project was to create a machine that will delaminate the composites, cut them, and heat them up to separate the resin from the composites so they can be recycled. A group was put together for the 2018-2019 academic year to further the project as a whole improve the operation of the device. The existing base was used as well as the cutter and the power sources. The upgrades included; a housing to support the transport rollers and changing from …

Exercise Machine Generator, Duane Harbick

All Undergraduate Projects

Exercise “spinning bikes” and bicycle training stands are common ways to maintain fitness and train for cycling. This exercise necessitates the user putting work into the machine by means of pedaling. In many instances the work put into exercise bikes and training stands is not taken advantage of. The objective of this project is an attempt to make use of some of the energy that a person would usually expend during exercise by building a generator that interfaces with multiple spinning bikes and training stands. It uses a synchronous pulley system to interface with the exercise machine and spin a …

Rc Baja Car Suspension, Tyler Martin

All Undergraduate Projects

This year the Mechanical Engineering Technology Department at CWU is holding an R/C Baja car competition using the same rules as the ASME competition. The designed car must compete in three separate events: the slalom course, drag race, and obstacle course. By not only completing, but also being competitive in each of the events, the car will be deemed a success. Suspension and steering are two essential components of any R/C car, and was the main focus for this report. The suspension must be able to support the car in the event of impacts. In addition, the steering must be …

Asme R/C Baja Car, Torrie Large

All Undergraduate Projects

How does one build a car? Do they start with the tires and build inward or do they develop separate aspects at the same time? This remote-controlled car was designed and built with the intention of competing in the annual Baja Competition. There are three competitions: sprinting, slalom, and an obstacle course. The suspension system of this car must be designed to support the car for both the physical build and the competitiveness. It must do this without interfering with the drive train and steering mechanism designed by Doug Erickson. The suspension system employs suspension arms attached to the chassis …

H.F. Hauff Electric Pruner Drive Train, Grady Graff

All Undergraduate Projects

The H.F. Hauff Company invests a large amount of money in developing a quality pruner used in everyday agriculture. Modern electric pruners tend to be expensive while manual tree pruning is very physically demanding. A battery assisted pruner that is light-weight, ergonomic, inexpensive to build and powerful enough to cut branches that a nominal apple tree would possess is the direct affiliation that H.F. Hauff devotes its funding too. A team of engineering students from Central Washington University developed a product with consideration to each of these circumstances. Since hand drills have proven to be user friendly and of abundance …

H.F. Hauff Pruner Cutting Blades, Wyley Stewart

All Undergraduate Projects

Apple orchards are a critical component of agriculture in the United States, and keeping the apple trees in the best shape for optimum growth and production is hard work. Neil Hauff, an agriculture industry expert, challenged students at CWU to engineer a power assisted tree pruner. Across the country, apple orchards need pruned every season. The pruning of the trees is strenuous manual labor that requires many man hours. The proposed solution is to create a power assisted tree pruner that would minimize the amount of work needed to trim each tree branch. This project has been separated into three …

Built-In Bicycle Rack For Cars, Scott A. Hansberry

All Undergraduate Projects

Transporting a bicycle after riding somewhere and then needing to be pickup can be problematic. Bicycles will not fit in most vehicles without removing components. There is also the risk of damaging the inside of the vehicle. Expecting everyone to have a bike rack for their vehicle is unrealistic because the bike rack could be considered unappealing visually, take up to much space in the trunk, or limit the vehicle owner’s access to the trunk. The solution to this problem is a bike rack that mounts onto your car and then mounts your bike onto the rack. Most people don’t …

Pin Router Duplicator, Daniel Phan

All Undergraduate Projects

The purpose of this project is to develop a pin router duplicator to accurately produce guitar bodies, necks, and fret boards. The pin router duplicator is designed to speed up the production process for the class Lean Manufacturing (MET 345), offered at Central Washington University. In the class, students learn how to work as a team to improve the way a woodshop is ran. In Lean Manufacturing, guitar bodies, necks, and fret boards are produced by using a CNC router. For this project, the motivation is to increase production by reducing production time. Accuracy and repeatability is also taken into …

High Accessibility Cabinet Insert, Matthew Leal

All Undergraduate Projects

Watching grandparents and parents get older, the struggle of day-to-day activities generally increases. One of the most recurring issues the older generation experiences nearly daily is their inability to reach dishes, glassware, and other things on the topmost shelves of a kitchen. Not only is it difficult for them to use things such as stepstools, it also becomes increasingly dangerous. With age, a fall from any height could be catastrophic. With this scenario in mind, a user-friendly cabinet insert would be a very effective way to combat this issue. However, many existing models of cabinet designed to fit these requirements …

H.F. Hauff Outrigger: Vertical Arm, Juan Tovar

All Undergraduate Projects

H.F. Hauff is a company based out of Yakima which specializes in farming equipment. One of their products is a trailer which has a wind machine attached to it. In order to keep the fan’s thrust from tipping the trailer over, the trailer needs outriggers to extend out. The outriggers also serve as a way to level out the trailer in uneven surfaces. The outriggers are what needed to be designed. This portion of the project was the vertical arm which extends from the horizontal arm, and goes towards the ground to raise the trailer. The project consisted of three …