Mechanical Engineering Commons^™

Android Drone: Remote Quadcopter Control With A Phone, Aubrey John Russell

Computer Engineering

The purpose of the “Android Drone” project was to create a quadcopter that can be controlled by user input sent over the phone’s Wi-Fi connection or 4G internet connection. Furthermore, the purpose was also to be able to receive live video feedback over the internet connection, thus making the drone an inexpensive option compared to other, equivalent drones that might cost thousands of dollars. Not only that, but the Android phone also has a host of other useful features that could be utilized by the drone: this includes GPS, pathing, picture taking, data storage, networking and TCP/IP, a Java software …

Microstructural Analysis Of Thermoelastic Response, Nonlinear Creep, And Pervasive Cracking In Heterogeneous Materials, Alden C. Cook

Electronic Theses and Dissertations

This dissertation is concerned with the development of robust numerical solution procedures for the generalized micromechanical analysis of linear and nonlinear constitutive behavior in heterogeneous materials. Although the methods developed are applicable in many engineering, geological, and materials science fields, three main areas are explored in this work. First, a numerical methodology is presented for the thermomechanical analysis of heterogeneous materials with a special focus on real polycrystalline microstructures obtained using electron backscatter diffraction techniques. Asymptotic expansion homogenization and finite element analysis are employed for micromechanical analysis of polycrystalline materials. Effective thermoelastic properties of polycrystalline materials are determined and compared …

Lattice Boltzmann Methods For Wind Energy Analysis, Stephen Lloyd Wood

Doctoral Dissertations

An estimate of the United States wind potential conducted in 2011 found that the energy available at an altitude of 80 meters is approximately triple the wind energy available 50 meters above ground. In 2012, 43% of all new electricity generation installed in the U.S. (13.1 GW) came from wind power. The majority of this power, 79%, comes from large utility scale turbines that are being manufactured at unprecedented sizes. Existing wind plants operate with a capacity factor of only approximately 30%. Measurements have shown that the turbulent wake of a turbine persists for many rotor diameters, inducing increased vibration …

Data Driven Low-Bandwidth Intelligent Control Of A Jet Engine Combustor, Nathan L. Toner

Open Access Dissertations

This thesis introduces a low-bandwidth control architecture for navigating the input space of an un-modeled combustor system between desired operating conditions while avoiding regions of instability and blow-out. An experimental procedure is discussed for identifying regions of instability and gathering sufficient data to build a data-driven model of the system's operating modes. Regions of instability and blow-out are identified experimentally and a data-driven operating point classifier is designed. This classifier acts as a map of the operating space of the combustor, indicating regions in which the flame is in a "good" or "bad" operating mode. A data-driven predictor is also …

Wind Farm Wake Modeling And Analysis Of Wake Impacts In A Wind Farm, Yujia Hao

Doctoral Dissertations

More and more wind turbines have been grouped in the same location during the last decades to take the advantage of profitable wind resources and reduced maintenance cost. However wind turbines located in a wind farm are subject to a wind field that is substantially modified compared to the ambient wind field due to wake effects. The wake results in a reduced power production, increased load variation on the waked turbine, and reduced wake farm efficiency. Therefore the wake has long been an important concern for the wind farm installation, maintenance, and control. Thus a wake simulation tool is required. …

A Haptic Surface Robot Interface For Large-Format Touchscreen Displays, Mark Price

Masters Theses

This thesis presents the design for a novel haptic interface for large-format touchscreens. Techniques such as electrovibration, ultrasonic vibration, and external braked devices have been developed by other researchers to deliver haptic feedback to touchscreen users. However, these methods do not address the need for spatial constraints that only restrict user motion in the direction of the constraint. This technology gap contributes to the lack of haptic technology available for touchscreen-based upper-limb rehabilitation, despite the prevalent use of haptics in other forms of robotic rehabilitation. The goal of this thesis is to display kinesthetic haptic constraints to the touchscreen user …

Experimental Building Demonstration Model With Viscous Fluid Dampers, Blake Thomas Reeve, Brianna Jean Kufa, Aden Malek Stepanians, Sophie Carmion Ratkovich

Architectural Engineering

The Architectural Engineering major places a heavy emphasis on structural dynamics and the role of wind and seismic loading in building analysis and design. Buildings of high importance that are critical to community function, such as hospitals, often utilize supplemental damping devices like supplemental viscous fluid dampers or base isolators to reduce the overall demands on the structural system. The design and analysis of these dampers are typically not taught at the undergraduate level, and is frequently performed by mechanical engineers, in lieu of structural engineers.

To better understand and research building behavior with supplemental damping devices, our multi-disciplinary team …

Creating Multi-Functional G-Code For Multi-Process Additive Manufacturing, Efrain Aguilera Jr

Open Access Theses & Dissertations

Additive manufacturing (AM) started over thirty years ago and with it a manufacturing revolution that moves industrial production into the personal home. With recent interest shifting into multi-functional parts fabricated through AM technologies, unified systems are being developed. Merging different manufacturing technologies into one single machine is a challenge but undergoing research has shown promise in the development of multi-functional systems. Concurrent work is being done in the software, automation, and hardware aspect of multi-functional systems. An effort to use industry compatible Computer Aided Design (CAD) software to design multi-functional parts including circuits, micro-machining, and foil embedding then exporting and …

Composite Model Representation For Computer Aided Design Of Functionally Gradient Materials, Fangquan Wang

Masters Theses

"Functionally Gradient Materials (FGMs) feature smooth transition from one material to another within a single object. FGMs modeling is considered to be one of the new challenges in Computer Aided Design (CAD) area. To overcome this challenge, this thesis presents a composite approach to model FGMs. The input in STL format can be meshed and voxelized in FGMs modeling system. The material composition in each voxel can be generated from multiple different types of control features. And LTI filters including Gaussian Filter and Average Filter are applied to blur default material features in order to generate FGMs inside models. The …