Mechanical Engineering Commons^™

Experimental And Numerical Characterization Of Multiphase Subsurface Oil Release, Feng Gao

Dissertations

Subsurface oil release is commonly encountered in the natural environment and engineering applications and has received the substantial attention of researchers after the disastrous Deepwater Horizon Blowout oil spill in 2009. The main focus on the present research is to systematically study the hydrodynamics of underwater oil jet under a variety of conditions, including the effect of dispersant and different gas to oil ratios (GOR) by using experimental measurement as well as a Computational Fluid Dynamics (CFD) approach, from which the measured turbulent characteristics (e.g., velocity, turbulent kinetic energy, turbulence dissipation rate, etc.) of underwater oil jet are thoroughly examined …

Elevated Temperature Progressive Damage And Failure Of Duplex Stainless Steel, Darren P. Luke

Civil Engineering ETDs

Ductile failure of metals has been the focus of research efforts within academia and industry for many years since it is tremendously important for understanding the failure of structures under extreme loading conditions. However, limited research has been dedicated to elevated temperature ductile failure, which is critical for evaluating catastrophic events such as industrial, structural or shipping vessel fires. A detailed investigation was conducted on the structural response of Duplex Stainless Steel at elevated temperatures. The temperature dependence of elastic modulus, yield strength, ultimate strength, and ductility was measured up to 1000°C and a continuum damage plasticity model was developed. …

Optimal Placement Of Distributed Energy Storage Systems In Distribution Networks Using Artificial Bee Colony Algorithm, Choton K. Das, Octavian Bass, Ganesh Kothapalli, Thair S. Mahmoud, Daryoush Habibi

Research outputs 2014 to 2021

The deployment of utility-scale energy storage systems (ESSs) can be a significant avenue for improving the performance of distribution networks. An optimally placed ESS can reduce power losses and line loading, mitigate peak network demand, improve voltage profile, and in some cases contribute to the network fault level diagnosis. This paper proposes a strategy for optimal placement of distributed ESSs in distribution networks to minimize voltage deviation, line loading, and power losses. The optimal placement of distributed ESSs is investigated in a medium voltage IEEE-33 bus distribution system, which is influenced by a high penetration of renewable (solar and wind) …

College Of Engineering Senior Design Competition Fall 2018, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge. The senior design competition helps focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects on …

Automated Compilation Test System For Embedded System, Mohamad Khairi Ishak, Ooi Jun Hwan, Teh Jiashen, Nor Ashidi Mat Isa

Makara Journal of Technology

Embedded system testing involves testing an integration of software and hardware. It is increasingly difficult to evaluate the functionality of each module within a short time because of the increasing number of tests required. In this paper, a novel stepwise methodology involving the use of an automated compilation test system (ACTS) is proposed, to improve the quality of testing and optimize the testing time using automation. Using the proposed method, the testing coverage can be maximized, while minimizing the manual work and testing time required. This ACTS was used to automate the test code compilation and execution for different hardware …

Transition Metal Dichalcogenide For High-Performance Electrode Of Supercapacitor, Saifful Kamaluddin Muzakir, Ahmad Salihin Samsudin, Bouchta Sahraoui

Makara Journal of Technology

Molybdenum dichalcogenides have been reviewed from the perspectives of bandgap, conductivity, and oxidation states of transition metal. Researchers have concluded that a narrow-bandgap transition metal dichalcogenide with high conductivity could be achieved for the high-performance electrode of a supercapacitor.

Ascorbic Acid Degradation In Cut Lemon Packaged Using Oxygen Scavenging Active Film During Storage, Kurniawan Yuniarto, Setyo Purwanto, Bruce Ari Welt, Anang Lastriyanto

Makara Journal of Technology

Oxygen scavenging active film can be used to prevent diffusion of free oxygen due to the action of permeation mechanism. In this study, biodegradable oxygen scavenging plastic film was designed by incorporating an antioxidant agent into plasticized polylactic acid or PLA-PEG (PPLA). Butylated hydroxytoluene (BHT) was added at different concentrations into the matrix of the PPLA film using a direct casting method to produce oxygen scavenging active film. The antiradical activity of the oxygen scavenging active film was observed, which could be applied for preventing vitamin C degradation in cut lemon during storage. The antiradical activity of the active film …

A 2.3/3.3-Ghz Dual Band Low Noise Amplifier Using Switchable Load Inductor In 0.18-Um Cmos Technology, Taufiq Alif Kurniawan, Hsiao-Chin Chen

Makara Journal of Technology

In this paper, the dual band low noise amplifier is designed in 0.18-μm CMOS technology. By combining the proposed switchable load inductor for gain controlling and the conventional inductive source degeneration topology, narrow band gain and good impedance matching are achieved at 2.3/3.3-GHz frequency bands. The new mathematical analysis of low noise amplifier design is derived to define the component parameters of the proposed circuits. The proposed low noise amplifier exhibits gain of 17.18 dB and 15.5 dB, and noise figure of 2.67 dB and 2.52 dB at the two frequency bands, respectively.

Conversion Of Heat Energy From Cooling Water Of Diesel Engine To Electrical Energy Using Thermoelectric Generator, Muhammad Hasan Albana

Makara Journal of Technology

This research objective is to convert heat from the radiator fluid of a diesel engine to electrical energy by utilizing a thermoelectric generator (TEG). The TEG consists of 20 semiconductors (TE modules) and is equipped with a heat sink. The research shows that using the TEG, the heat of radiator fluid can be converted to electrical energy, although the electricity generated is small. The maximum electrical voltage generated by the TEG when modules were connected in series was 10 volts. When the TE modules were connected in parallel and series-parallel, the maximum voltages generated were 2.11 and 2.53 volts, respectively. …

The Importance Of Usability Aspect In M-Commerce Application For Satisfaction And Continuance Intention, Yassierli Yassierli, Vinsensius Vinsensius, M. S. Syed Mohamed

Makara Journal of Technology

There has been a rapid growing of m-commerce application in recent years due to the development of mobile communication technology and e-commerce business. However, only about 30% of online users, who conduct online searching, make online purchases. The low conversion rate seems to be correlated with poor usability aspect of most m-commerce applications and poor satisfaction reported by users. Research has reported that satisfaction and continuance intention in using m-commerce applications have relationships with service quality and information quality. In this study, a new model of user satisfaction and continuance intention in the context of mobile application was proposed by …

Activated Carbon Fixed-Bed Adsorber Design For Treating Chromium Hexavalent Wastewater, Tedi Hudaya, Velicia Rachmat

Makara Journal of Technology

Pollution caused by industrial wastewater containing heavy metals is a major issue, primarily due to its toxic nature. A cheap yet effective method to deal with such wastewater is activated carbon adsorption. The purpose of this research is to evaluate and design a fixed bed adsorber with granular activated carbon as an adsorbent to process wastewater-containing chromium hexavalent (Cr 6+). Experiments show that the Langmuir isotherm fits the equilibrium data as effectively as the Freundlich isotherm. Activated carbon used in this research is Jacobi 2000® derived from bituminous coal. The lab scale inlet volumetric flow is 100 mL/h with different …

Immittance Response On Carboxymethyl Cellulose Blend With Polyvinyl Alcohol- Doped Ammonium Bromide-Based Biopolymer Electrolyte, Norfatihah Mazuki, Yuki Nagao, Ahmad Salihin Samsudin

Makara Journal of Technology

The blended carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVA) doped with various compositions of ammonium bromide (NH4Br)-based solid biopolymer electrolytes (SBEs) were prepared by using the casting method. In this present work, CMC/PVA–NH4Br SBE thin film was used to investigate the electrical conductivity via electrical impedance spectroscopy. The maximum conductivity obtained was 3.21 X 10−4 S cm−1 for sample AB20 at ambient temperature (303 K), and this result might be due to the increased number of charge carrier. A dielectric study was conducted to understand the conductivity behavior. The electrical properties have been measured as a function of frequency of …

Towards Environmentally Sustainable And Cost-Effective Food Distribution In The U.S., Jasmina Burek

Graduate Theses and Dissertations

Distribution centers (DCs) and supermarkets have an important role in food sustainability, but no previous research has accounted for their environmental impact. The purpose of this research was to assess environmental sustainability of grocery, perishables, and general merchandise DCs; to estimate food storing and retailing impact; and to provide cost-effective strategies to reduce DCs’ environmental impacts. The importance and relevance of the research is threefold: improving sustainability of DCs, food storing, and food retailing. The main method used in this research was the life cycle assessment (LCA) method. An initial study calculated environmental impacts of the Wal-Mart Stores, Inc. DCs, …

Evaluation Of Deformable Posts In The Zoi And Rigid Posts In Stiff Soil, Thomas Ammon

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Debris fences are commonly used by states, in conjunction with a concrete parapet, to protect railway tracks. Their use limits the intrusion of debris that could damage tracks or clutter rail lines. Due to a lack of previously crash-tested systems, the safety performance of such designs are largely unknown. The Iowa Department of Transportation (DOT) desired that researchers at the Midwest Roadside Safety Facility (MwRSF) design a crashworthy debris fence mounted on top of a concrete parapet to meet the Manual for Assessing Safety Hardware (MASH) TL-3 crash test conditions. Part 1 of this thesis details the literature review and …

Transient Analysis Of Full Scale And Experimental Downburst Flows, Junayed Chowdhury

Electronic Thesis and Dissertation Repository

Downbursts are highly transient natural phenomena which produce strong downdrafts evolving from a cumulonimbus cloud They induce an outburst of damaging winds on or near to the ground causing an immense damage to the ground mounted structures and aircrafts. This study investigates the transient nature of downbursts using wind speed records from full scale downburst events employing an objective methodology. This method can detect the abrupt change points in a downburst time series based on statistical parameters such as mean, standard deviation and linear trend. In addition to the analysis of the full scale downburst events, several large scale experimental …

Toward Building Resilient, Sustainable, And Smart Infrastructure In The 21st Century, Aly Mousaad Aly

Faculty Publications

In recent years, as a result of significant climate change, stringent windstorms are becoming more frequent than before. Given the threat that windstorms bring to people and property, wind/structural engineering research is imperative to improve the resilience of existing and new infrastructure, for community safety and assets protection. The Windstorm Impact, Science and Engineering (WISE) research program at Louisiana State University (LSU) focuses on creating new knowledge applicable to the mitigation of existing and new infrastructure, to survive and perform optimally under natural hazards. To achieve our research goals, we address two imperious challenges: (i) characterization of realistic wind forces …

The Subject Librarian Newsletter, Engineering And Computer Science, Spring 2018, Buenaventura "Ven" Basco

Buenaventura "Ven" Basco

No abstract provided.

The Subject Librarian Newsletter, Engineering And Computer Science, Fall 2017, Buenaventura "Ven" Basco

Buenaventura "Ven" Basco

No abstract provided.

Experimental Tests And Numerical Simulations For Failure Investigation On Corrugated Boxes Used On Household Appliance Packaging, Diego Fernandes Rodrigues, José Carlos Pereira

Journal of Applied Packaging Research

Packages made of corrugated paper are fundamental to the protection, transportation and handling of the appliance product market. During the storage and sales stages of a product, the package must resist compressive loads in different directions beyond moderate impacts. In this context, the objective of this work is to develop and implement a post-processor that allows the simultaneous analysis of two of the most common failure modes of packages made of corrugated paper: failure due to tensile or compressive stress limit, and failure due to local buckling, when the buckling of the faces of the corrugated paper between two peaks …

Multi-Objective Bayesian Optimization Of Super Hydrophobic Coatings On Asphalt Concrete Surfaces, Ali Nahvi, Ali Arabzadeh, Alireza Sassani, Mohammadkazem Sadoughi, Halil Ceylan

Ali Nahvi

Internet Traffic Forecasting Model Using Self Organizing Map And Support Vector Regression Method, Enrico Laoh, Fakhrul Agustriwan, Chyntia Megawati, Isti Surjandari

Makara Journal of Technology

Internet traffic forecasting is one of important aspect in order to fulfill the customer demand. So, the service quality of internet service provider (ISP) can be maintained at the good level. In this study self organizing map (SOM) and support vector regression (SVR) algorithm are used as forecasting method. SOM is first used to decompose the whole historical data of traffic internet into clusters, while SVR is used to build a forecasting model in each cluster. This method is used to forecast ISPs traffic internet in Jakarta and surrounding areas. The result of this study shows that SOM-SVR method gives …

Satellite-Based Monitoring Of Spatiotemporal Changes In Batudulang Forest In Sumbawa, Indonesia, Mohammad Muslim, Arief Budhi Witarto, Wahyu Indrajaya

Makara Journal of Technology

Space-based earth observation technology applicable to forest inventory and monitoring is well known in the scientific community. High-resolution satellite images form an important data source for forest mapping and change detection at regional and national scales. The value of forest change information derived from remote sensing data is significantly enhanced if this information is integrated into a spatially explicit geographic information system. Satellite-based rapid assessment was conducted to measure spatiotemporal changes in Batudulang forest over the years. The general approach to quantify change in the spatial aspect of the forest involved change detection using moderate-resolution imaging spectro-radiometer satellite-based normalized difference …

Effects Of The Preheating Temperature On The Crystal Structure And Texture Of Martensitic Stainless Steel, Tri Hardi Priyanto, Rifai Muslih, Herry Mugirahardjo, Bharoto Bharoto, Andon Insani, Muzzakiy Muzzakiy

Makara Journal of Technology

Theoretically, the preheating temperature refers to the start martensite temperature (Ms), and the martensite transformation can be considered as the conservation of the invariant habit-plane in the lattice structure. The habit-plane is the interface plane between austenite and martensite as measured on a macroscopic scale. From the calculation, Ms = 252 °C. The martensite formation can be affected by temperature or stress treatment. In this experiment, temperature treatment was conducted. The sample was treated at 250 °C ± 10 °C. Before and after the pre-heat treatment, the sample was characterized using the neutron diffraction method. BATAN’s Texture Diffractometer (DN2) with …

Strength Structure Analysis Of Main Gate Graving Dock Using Pontoons For Condition Repairs, Budianto Budianto

Makara Journal of Technology

Main gate graving dock with pontoon type can certainly suffered some level of damage after a long period of operation. Many employments within the graving dock can delay the process repair of main gate. The main gate may not be opened, because employees are still working to ship fabrication process under sea waterline. For accommodate these interrelated conditions, the best solution with repair one side of the main gate with type pontoon and employees can still work ship fabrication process in graving dock conducted simultaneously. The repair process conditions must be required main gate structure that consists of only one …

Mapping Of Bruise Of Oil Palm Fresh Fruit Bunch During Loading And Transportation From Field To Mill, Andreas Wahyu Krisdiarto

Makara Journal of Technology

Fresh fruit bunches (FFBs) are used as raw materials for palm oil, and their transport from a field is a critical step to maintain their quality. Fruit integrity should be maintained so the mill can efficiently obtain palm oil with less than 5% free fatty acid content. Physical treatments for FFBs during loading to truck bins and transport may cause physical injuries. This research aimed to map fruit bruises. The map can be used as a basis in managing transport of FFBs. Physical injuries were assessed by bruise index (BI), which was calculated by measuring the bruise area and weight …

Benchmarking Product Service System Of Generator Set Distributors, Venny Violetta Tiurindah, Tanika Dewi Sofianti

Makara Journal of Technology

Power generation is an industry that is essential to sustain daily life and competes with generator set distributors. The product service system of distributors must be improved to survive the competition. This research aims to develop tools for benchmarking the product service system of generator set distributors. Benchmarking identifies gaps between a product and other competitors’ products. In this work, a product service system board is used to visualize the current product service system of a generator set distributor. A PPIAF framework and a SERVQUAL framework are adapted to assess product performance and service quality, respectively. AHP is used as …

Purdue Air Sense: A Methodology For Improving The Accuracy Of Ambient Aerosol Mass Concentration And Size Distribution Measurement With Low-Cost Optical Sensing Techniques, Rishabh Ramsisaria, Satya Sundar Patra, Brandon Emil Boor

The Summer Undergraduate Research Fellowship (SURF) Symposium

There is a global lack of a means for monitoring air pollutant levels at a local level due to expensive and bulky instrument requirements. It is important to monitor toxic gas levels, as well as particulate matter levels, in the atmosphere to study their effects on human health and to further develop city- and community-level air pollution solutions. In this study, with the means of a Raspberry Pi, low-cost Alphasense Optical Particle Counter and gas sensors, and methodical calibration techniques, we built a portable 3-D printed module powered by clean electricity generated by an on-board Voltaic solar cell that measures …

Microstructures And Hardness Of Tig Welded Experimental 57fe15cr25ni Steel, Parikin Parikin, Mohammad Dani, Abu Khalid Rivai, Agus Hadi Ismoyo, Riza Iskandar, Arbi Dimyati

Makara Journal of Technology

The microstructures and hardness of tungsten inert gas (TIG) welded experimental 57Fe15Cr25Ni steel were investigated through optical–scanning electron microscopy analyses and with a hardness tester, respectively. The welding process restructured the constituent atoms into regular and irregular crystal lattices. Rapid cooling of the weld metal allowed the formation of a dendritic (columnar) structure, with porous grains. By contrast, slow cooling influenced HAZ and led to the formation of grain structures. The crystal lattice became more organized and larger than other zones. Meanwhile, the base metal formed circular nets that covered large area inside thick and thin grain boundaries. The diffraction …

Investigation Of Ship Hull Girder Strength With Grounding Damage, Muhammad Zubair Muis Alie, Ristiyanto Adiputra

Makara Journal of Technology

The objective of the present study is to investigate ship hull girder strength as a result of grounding damage upon longitudinal bending. A bulk carrier and tanker are analyzed and Smith’s Method is adopted and implemented in the analysis program. An efficient solution procedure is performed by assuming the cross-section remains plane and the vertical bending moment is applied to the cross section. As a fundamental case, the damage is simply created by removing the elements from the cross section. Welding residual stress, initial imperfections, and crack extensions are not considered. The grounding damage is made by two conditions, namely …

Selecting The Most Effective Energy Modeling Tool Based On A Project Requirement, Sodiq Akande

Electronic Theses and Dissertations

Building energy usage can be derived and controlled by performing building energy modeling. BEM can be performed using numerous software tools such as DesignBuilder, OpenStudio, EnergyPlus etc. These modeling tools can be sorted into three different modeling categories: Black-box, Gray-box and White-box. It is important for a modeler to be able to quickly select the proper tool from the proper category to meet the need of the project. To validate the method of categorizing tools, the three models generated using tools from each category and the modeling outputs required were compared. Each model was designed to estimate the amount of …