Mechanical Engineering Commons^™

Shallow-Water Wind Turbine Foundation, Andrew Walker, Nico Nani, James Cusanelli, Zachary Dunkelberger

Mechanical Engineering

Over the 2021-2022 academic year, we, the Shallow Water Wind Turbine Foundation senior project team, designed, manufactured, and tested a fixed bottom, sand mounted turbine foundation for the Cal Poly Wind Power Club’s Collegiate Wind Competition turbine. The foundation was restricted to certain material, installation, and geometric constraints outlined in this report, and needed to support the turbine under operating conditions including 22 m/s wind speeds. The design was analyzed using primarily a bearing capacity geotechnical analysis to determine final geometry and weight. The foundation was then manufactured using welded, custom carbon steel parts.

The foundation was inspected for geometric …

Gaylord Produce Removal Machine, Marcus Takashi Hirose Lee, Jacob Michael Perlman, Carissa Abigail Kamm, Mark Misao Loera

Mechanical Engineering

This Final Design Review Report outlines the senior design project that began Winter Quarter of 2021 at California Polytechnic State University. Our team consists of three mechanical engineers and a general engineer, working together to design, build, and test a product for Alameda County Food Bank. The goal of the final product is to relieve volunteers and employees of tedious manual labor and increase efficiency during the removal of produce from large Gaylord containers. This document describes background research, the objectives of the project, chosen concept design, analysis and initial prototyping of said concept, the final design, and verification prototype …

Model Block Press Design, Ben Todd Van Hamersveld, Chester Wong, Alexander Wing-Jon Giannousis

Mechanical Engineering

This project’s goal is to redesign the Center for Vocational Building Technology (CVBT) BP9 earth block press, which makes 1/3 scale compressed earth blocks to build demonstration model homes in Thailand. The full-scale block press, the BP6, provides a sustainable and affordable technique for constructing habitable homes in Thailand. The BP9 serves as a tool to inform the public of the advantages of human-powered earth block presses through demonstration. The BP9 press design has multiple problems: it is too expensive to manufacture, there is too much friction when used, it has several weak points due to users unintentionally applying excessive …

Cal Poly India Project, Derek Babine, Austen Hibler, Alex Hernandez

Mechanical Engineering

This report documents the research, ideation, and development of a solution, implemented by the Cal Poly India Sanitation Team per the request of Mr. Harish Bhutani, to solve the problem of hazardous human waste management in poor villages in India. The sponsor envisioned a universal design that would give each household in those villages access to a private toilet system because the current solution is open defecation in water sources and farming fields. The initial constraints required the project be low cost, not use of electricity or water, have the ability to cater to an 8-10 person household, and be …

Sodhana Environmental - Final Design Report, Eric Taylor, Corissa Bellis, Cody Perez, Cameron Zeller

Mechanical Engineering

A fully designed cost-effective, sustainable, toilet for the developing world.

Throwing Frame For Athletes With Dissabilities, Andrew Higgins, Stefan Owechko, Gabriel (Gabe) Terrasas, Kevin Crisfield

Mechanical Engineering

Team Zeus’ senior project was to design, build and test a working throwing frame system for Bridge II Sports, a nonprofit organization in North Carolina. The throwing frame is used to allow athletes and individuals with disabilities to throw shot-put, discus, and javelin using a frame to sit against. Team Zeus was specifically tasked to build a frame that is lighter weight and more transportable than products that are currently on the market. This frame also is adjustable to accommodate a wide range of athlete weights, sizes, and abilities. The final result is a 35lb aluminum frame with two different …

Vibroacoustic Study Of Circular Cylindrical Tubes In Roller Coaster Rails, Joshua I. Davis, Charles Birdsong, Harold M. Cota

Mechanical Engineering

Excessive noise generated by roller coasters during operation is a significant issue for amusement parks located near residential and business districts. Previous work showed that filling the rails with sand and pea gravel can provide noise reduction levels of up to 10 and 15 decibels. However, using damping materials may require additional support structures to accommodate the weight increase and, consequently, raise installation costs. This paper presents field results that characterize sound and vibration of roller coasters with different rail geometry and fill. Finite element modeling is used to compute the theoretical natural frequencies and mode shapes of a typical …

Piedras Blancas Light Station Vista Point Improvement Plan, Larissa Heeren, Reuben Juster, Annamarie Usher, John Rossi, Nick Mitchell

Mechanical Engineering

Piedras Blancas Light station Improvement Involved the design of two separate parking lot/vista point plans as well as the creation of a concrete Iron Ranger located near the gift shop on site.