Mechanical Engineering Commons^™

A Finite Element Simulation Of Temperature And Material Flow In Fricton Stir Welding, Mark J. Lasley

Theses and Dissertations

The purpose of this research was to use the Transvalor S.A. product, Forge3, to develop a finite element simulation of the friction stir welding process that improves the predictability of temperature evolution and material flow within the plunge portion of the process. Previous modeling created more heating within the billet than experimental results, probably due to the simplification of the simulation with adiabatic boundary conditions. More realistic tooling temperatures were included in this model as these affect heat evolution which is a determining factor in microcrystalline growth. These results were validated by experimental efforts using a billet and tooling instrumented …

Influence Of Connection Placement To The Behavior Of Precast Concrete Exterior Beam-Column Joint, Elly Tjahjono, Heru Purnomo

Makara Journal of Technology

Influence of Connection Placement to the Behavior of Precast Concrete Exterior Beam-Column Joint. This paper presents an experimental study on the influence of connection placement to the behaviour of exterior beamcolumn joint of precast concrete structure under semi cyclic loading. Four half-scale beam-column specimens were investigated. Three beam-columns were jointed through connection that are placed in beam-column joint region and the forth is connected at the plastic hinge potensial region of the beam. Crack patterns, strength, stiffness and ductility of the test specimens have been evaluated. The test result indicated that all beam-column specimens show good ductility behavior.

The Effects Of Influent Debit On Hydrodynamic Characteristic Of Bojongsoang Facultative Pond: Without Wind Effects, Rositayanti Hadisoebroto, Suprihanto Notodarmojo

Makara Journal of Technology

The Effects of Influent Debit on Hydrodynamic Characteristic of Bojongsoang Facultative Pond: Without Wind Effects. The performance of facultative pond in Bojongsoang WWTP have reported to be unstable. One of the cause of the unstable performance is the hydrodynamic characteristics that not met the criterion. The improper hydrodynamic characteristics are included the existence of dead-zone, the short-circuiting, and the turbulence due to eddy current. The study was to analyze the effect of the influent debit variation on the hydrodynamic characteristics of the pond using mathematical model. The two-dimensional hydrodynamic model was built from two hydrodynamic equations which are continuity and …

Optic Properties On Aggase2 Polycristal Fabrication, A. Harsono Soepardjo, I Dewa Made Janusetiawan

Makara Journal of Technology

Optic Properties on AgGaSe2 Polycristal Fabrication. Polycristal AgGaSe2, is compound (I-III-VI2) a semiconductor as basic material for thin film for solar cell. Polycristal was succesfully grown using Bridgmann Method, heated on sequential temperature treatment until 850°C and cooled down slowly until room temperature. Results observed were in the form of ingot (bars) with more or less 3 cm length and 13 mm in diameter. By using X-Ray Fefraction, composition obtained of each element (weight %) was Ag = 29,3996 %, Ga = 36,8123 % and Se = 30,29 % while using X-Ray Difraction lattice parameter obtained/calculated a = 4,4112 Å, …

Modelling And Simulation Of Packed Bed Catalytic Converter For Oxidation Of Soot In Diesel Powered Vehicles Flue Gas, Mohammad Nasikin, Praswasti P.D.K. Wulan, Vita Andrianty

Makara Journal of Technology

Modelling and Simulation of Packed Bed Catalytic Converter for Oxidation of Soot in Diesel Powered Vehicles Flue Gas. Diesel vehicle is used in Indonesia in very big number. This vehicle exhausts pollutants especially diesel soot that can be reduces by using a catalytic converter to convert the soot to CO2. To obtain the optimal dimension of catalytic converter it is needed a model that can represent the profile of soot weight, temperature and pressure along the catalytic converter. In this study, a model is developed for packed bed catalytic converter in an adiabatic condition based on a kinetic study that …

Fuel Injection System For One Cylinder Motor Cycle Engine, Bambang Sugiarto

Makara Journal of Technology

Fuel Injection System for One Cylinder Motor Cycle Engine. Fuel injection has been developed for many years. But its common application is limited on car’s engine. With many reason fuel injection systems in motorcycle one cylinder engine has not been widely used yet. Fuel Injection System allows the amount of fuel, injected to be controlled appropriate to engine parameters such as engine speed, amount of air inducted to cylinder, temperature, for each cycle, over the entire engine operating conditions. This fuel injection research is done to find out the Volumetric Efficiency of the intake manifold system, the amount of fuel …

Thermodynamic Analysis Of Separation Systems, Yaşar Demirel

Papers in Thermal Mechanics

Separation systems mainly involve interfacial mass and heat transfer as well as mixing. Distillation is a major separation system by means of heat supplied from a higher temperature level at the reboiler and rejected in the condenser at a lower temperature level. Therefore, it resembles a heat engine producing a separation work with a rather low efficiency. Lost work (energy) in separation systems is due to irreversible processes of heat, mass transfer, and mixing, and is directly related to entropy production according to the Gouy-Stodola principle. In many separation systems of absorption, desorption, extraction, and membrane separation, the major irreversibility …

Biomimetic Actuators: Where Technology And Cell Biology Merge [Review Article], Michael Knoblauch, Winfried Peters

Winfried S. Peters

Exergy Use In Bioenergetics, Yaşar Demirel

Papers in Analytical Chemistry

Every developed and adapted biological system extracts useful energy from outside, converts, stores it, and uses for muscular contraction, substrate transport, protein synthesis, and other energy utilizing processes. This energy management in a living cell is called the bioenergetics, and the useful energy is the exergy, which is destroyed in every irreversible process because of the entropy production. The converted exergy is the adenosine triphosphate (ATP) produced through the oxidative phosphorylation coupled to respiration in which the exergy originates from oxidation of reducing equivalents of nutrients. A living cell uses the ATP for all the energy demanding activities; it has …

Layer-By-Layer Nanoassembly Combined With Microfabrication Techniques For Microelectronics And Microelectromechanical Systems, Jingshi Shi

Doctoral Dissertations

The objective of this work is to investigate the combination of layer-by-layer self-assembly with microfabrication technology and its applications in microelectronics and MEMS.

One can assemble, on a standard silicon wafer, needed multilayers containing different nanoparticles and polymers and then apply various micromanufacturing techniques to form microdevices with nanostructured elements.

Alternate layer-by-layer self-assembly of linear polyions and colloidal silica at elevated temperatures have been firstly studied by QCM and SEM. LbL self-assembly and photolithography were combined to fabricate an indium resistor. The RTA method was employed in the fabrication. Hot-embossing technique as a reasonably fast and moderately expensive technique was …

Secondary Flow Experimental Study For Axial Compressor Cascade Strong Stagger With And Without Tip- Clearance: Static Pressure Distribution On Blade Surface, Syamsuri Syamsuri

Makara Journal of Technology

Secondary Flow Experimental Study for Axial Compressor Cascade Strong Stagger With and Without Tip- Clearance: Static Pressure Distribution on Blade Surface. The performance of blade cascade is influenced by the growth and boundary layer’s separation along blade surface and endwall (casing and hub). The secondary flow which happens near hub and casing compressors is three dimentional flow separation phenomenon comes from interaction blade boundary layer with casing and hub boundary layers in the compressor. The secondary flow causes secondary losses, blockage effect, and turning angle (deflection) distribution along blade span. The result of the research shows that the increase of …

Synthesize Of Emulsion Polymer Latex For Sub-Grade Cbr Improvement In The Road Construction, Keba Moto, V. Julian, Syamsudin Syamsudin, T. A. Wiradi, S. R. Wijaya

Makara Journal of Technology

Synthesize of emulsion polymer latex for sub-grade CBR improvement in the road construction. Latex polymer for California Bearing Ratio (CBR) enhancement in sub-grade soil of road building has been prepared by emulsion polymerizations technique. The prepared polymer then characterize by Fourier Transform Infrared (FTIR). For application purpose, CBR test was done to the compacted polymer added-soil. The CBR test is done also for both soaked and unsoaked samples. It is found that our latex polymer is better then other imported latex polymer. For the latex polymer, which is design to have Temperatur glass (Tg) around 9.8-19.6o, indicating the formation of …

Effect Of Photoperiodicity On Co2 Fixation By Chlorella Vulgaris Buitenzorg In Bubble Column Photobioreactor For Food Supplement Production, Anondho Wijanarko, Dianursanti Dianursanti, Arief Budi Witarto, Roekmijati Widaningroem Soemantojo

Makara Journal of Technology

To reduce the level of CO2 content in air, effort on converting CO2 to useful products is required. One of the alternatives includes CO2 fixation to produce biomass using Chlorella vulgaris Buitenzorg. Chlorella vulgaris Buitenzorg is applied for production of food supplement. Chlorella vulgaris Buitenzorg is also easy to handle due to its superior adaptation. Currently, Chlorella vulgaris Buitenzorg has been analyzed by some experts for its cellular composition, its ability to produce high quality biomass and the content of essential nutrition. A series of experiments was conducted by culturing Chlorella vulgaris Buitenzorg using Beneck medium in bubbling column photobioreactor. …

Wavelenght-Dispersive X-Ray Flourescence Accuration, H. Widyatmoko

Makara Journal of Technology

Wavelenght–Dispersive X-Ray Flourescence Accuration. X-Fuorescence spectrometry is a method, which is increasingly applied in the geochemical analysis. X-Fuorescence spectrometry is classified under two categories – WDXRF (wavelenght – dispersive X-ray fluorescence spectrometer) and EDXRF (energy-dispersive X – ray fluorescence spectrometer). WDXRF can be configured as a sequential spectrometer , a simultaneous spectrometer or a hibrid instrument, which combines the advantages of the simultaneous and sequential spectrometers into one instrument. Each instrument is different in some characteristics, and each has applications for which it is specifically suited. In this investigation sequential spectrometer PW 1450 was used to analyze the major, minor …

Project-Based Introduction To Engineering - A University Core Course, Samuel Bogan Daniels, Bouzid Aliane, Jean Nocito-Gobel, Michael Collura

Engineering and Applied Science Education Faculty Publications

This paper describes a first year engineering course that is taken by both engineering and non-engineering students. The project-based Introduction to Engineering course, EAS107P, fulfills a university core curriculum elective. Although engineering students take the course during their first year, students from other majors typically elect to take the course later in their curriculum. The focus of EAS107P is to have students experience the engineering design and problem solving process in a multi-disciplinary, team-based setting. In addition to learning about design, students develop an interest in the engineering profession and build a foundation of skills for future work. An additional …

Development Of A Multidisciplinary Engineering Foundation Spiral, Samuel Bogan Daniels, Bouzid Aliane, Jean Nocito-Gobel, Michael Collura

Engineering and Applied Science Education Faculty Publications

To operate effectively in today’s workforce engineers need to have a muti-disciplinary perspective along with substantial disciplinary depth. This broad perspective cannot be achieved by merely taking 2 or 3 engineering courses outside of the major, but rather will require a radical change in the way we educate engineers. The faculty of the School of Engineering and Applied Science at the University of New Haven have developed a new approach: the Multidisciplinary Engineering Foundation Spiral. This curricular model provides the needed mix of breadth and depth, along with the desired professional skills, by providing carefully crafted, well-coordinated curricular experiences in …

Project-Based Introduction To Engineering -- Course Assessment, Samuel Bogan Daniels, Michael Collura, Bouzid Aliane, Jean Nocito-Gobel

Engineering and Applied Science Education Faculty Publications

The School of Engineering and Applied Science at the University of New Haven has a newly developed project-based Introduction to Engineering course. This new course plays a central role in the new Multi-Disciplinary Engineering Foundation Spiral curriculum as the first semester course for all engineering freshmen. An assessment process was developed to determine the effectiveness of this project-based course, specifically with attention towards assessing attitudes, impact on retention, problem-solving and engineering foundation topics. This paper addresses the particular portion of the assessment process for the individual course projects and their contribution to the last two assessment categories.

Project Planning & Development For Engineering Freshmen, Bouzid Aliane, Michael Collura, Samuel Bogan Daniels, Jean Nocito-Gobel

Engineering and Applied Science Education Faculty Publications

The nature and background of students seeking an engineering education has changed drastically in the last decade, as has the expectations of industrial employers. Many students lack the organizational skills needed for academic success. Similar organizational skills, although more advanced, are required for managing engineering projects. A new course was developed by the faculty at the School of Engineering and Applied Science at the University of New Haven. Through this course, a key component of the Multidisciplinary Engineering Foundation Spiral, seeks to promote higher retention rates, increase student motivation and begin a confidence-building transition to professional practice. Project management concepts …

Design And Simulation Of An Induction Skull Melting System, Taide Tan

UNLV Theses, Dissertations, Professional Papers, and Capstones

Incorporating volatile actinides, mainly americium into a metallic fuel pin (MFP) has been a serious problem due to americium’s high vapor pressure. An Induction Skull Melting (ISM) system was identified by Argonne National Laboratory (ANL) as a potential furnace design to cast MFPs. Through the development of the ISM system, the nuclear waste feedstock can be melted and injected into the mold for fabricating MFPs in the advanced nuclear fuel cycles. The main phenomena in this system include: induction melting process, casting process and mass transfer process of americium. Issues related to ISM system design for casting MFPs are discussed …

Graded Channel Mosfet Simulation With S-Pisces 2b, Hartono Siswono

Makara Journal of Technology

Graded Channel MOSFET simulation with S-Pisces 2B. Graded-Channel Metal-Oxide-Semiconductor Field-effect- Transistor or GCMOSFET is being discussed in this paper. GCMOSFET technology has been developed to meet the growing demand for low power and high performance application. In this paper, it will be shown that, compared to ungraded MOSFET, the GCMOSFET device offers the advantage of significantly higher drive current. The higher drive current is achieved because the effecctive channel length of GCMOSFET is shorter than the ungraded MOSFET’s. From the simulation result with S-PISCES 2B and MATLAB, it can been shown that the ID from GCMOSFET is higher than the …

Construction Of Depth-Structure Shelf-Edge Map For Case Study Of Kujung Formation, East Java Sea, Saifatur Rusli, Suparto Suparto

Makara Journal of Technology

Construction of Depth-Structure Shelf-edge Map for Case Study of Kujung Formation, East Java Sea. In general, reflection seismic method has capability to represent sub-surface in time domain. Seismic cross-section that depicts the formation of sub-surface usually use time domain in the format of TWT (Two Way Times). This due to in the process of seismic data acquisition, seismic wave propagates in down-going and up-going manner so that the obtained results from data processing are in the format of TWT seismic vs. shot points. This paper will describe the construction of depth-structure map for case study of Kujung Formation, East Java …

Fatigue Of Drill Pipes Used In Horizontal Directional Drilling, Feibai Ma

Doctoral Dissertations

Fatigue is the most common cause of mini-HDD drill rod failure. It can occur at stress levels far below the normal operating stress in most drill stem components. Fatigue failures occur because the drill rod, after it has been forced into a curved path, undergoes a cyclic bending stress oscillating from tension to compression in concert with the other stress components caused by torque, thrust, or pullback.

When a rod breaks underground, there is considerable extra cost caused by the delay in “fishing” out the broken rod as well as the cost of replacing the rod. On the other hand, …

Analysis Of Kancil's Car Knuckle Prototype, Tresna P. Soemardi, Aida Mahmudah

Makara Journal of Technology

Analysis of Kancil’s Knuckle Prototype. The objective of this work is to execute strength analysis of knuckle, which is made from FCD 50, by using static analysis on maximum loading. This maximum loading is obtained from front axle loading calculation on particular operating condition. That is, vehicle is braking while cornering in down hill. From previous vehicle loading calculation, we get a number of loading values on different speed and deceleration. At the end, we get a value of speed and deceleration that guarantee the vehicle safety if it is braking while cornering in down hill. As comparison, loading calculation …

Quarternair Cugasete And Cuga0.5in 0.5te2 Thin Films Fabrication Using Flash Evaporation, A. Harsono Soepardjo

Makara Journal of Technology

Quarternair CuGaSeTe and CuGa0.5In 0.5Te2 Thin Films Fabrication Using Flash Evaporation. Quarternair materials CuGaSeTe and CuGa0.5In 0.5Te2 are the basic materials to solar cell fabrication. These materials have high absorption coefficients around 103 – 105 cm-1 and band gap energy in the range of 1-5 eV. In this research, the films were made by flash evaporation method using quarternair powder materials of CuGaSeTe and CuGa0.5In 0.5Te2 to adhere in a glass substrate. After the films were obtained, the properties of these films will be characterized optically and electrically. The lattice parameter of the films and the crystalline film structure were …

Pid Fuzzy Logic Controller System For Dc Motor Speed Control, H. Samsul Bachri M.

Makara Journal of Technology

PID Fuzzy Logic Controller System for DC Motor Speed Control. A good controller system must have resilience to disturbance and must be able to response quickly and accurately. Problem usually appears when PID controller system was built sensitively hence the system’s respon to the disturbance will yield big overshot/undershot then the possibility of oscillation to be happened is excelsior. When the controller system was built insensitively, the overshot/undershot will be small but the recovery time will be longer. Hybrid controller system could overcome those problems by combining PID control system with fuzzy logic. The main control of this system is …