Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 4 of 4
Full-Text Articles in Mechanical Engineering
Do Surfaces With Mixed Hydrophilic And Hydrophobic Areas Enhance Pool Boiling?, Amy Rachel Betz, Jie Xu, Huihe Qiu, Daniel Attinger
Do Surfaces With Mixed Hydrophilic And Hydrophobic Areas Enhance Pool Boiling?, Amy Rachel Betz, Jie Xu, Huihe Qiu, Daniel Attinger
Daniel Attinger
We demonstrate that smooth and flat surfaces combining hydrophilic and hydrophobicpatterns improve pool boiling performance. Compared to a hydrophilicsurface with 7° wetting angle, the measured critical heat flux and heat transfer coefficients of the enhanced surfaces are, up to respectively, 65% and 100% higher. Different networks combining hydrophilic and hydrophobic regions are characterized. While all tested networks enhance the heat transfer coefficient, large enhancements of critical heat flux are typically found for hydrophilic networks featuring hydrophobic islands. Hydrophilic networks indeed are shown to prevent the formation of an insulating vapor layer.
Use Of A Porous Membrane For Gas Bubble Removal In Microfluidic Channels: Physical Mechanisms And Design Criteria, Jie Xu, Regis Vaillant, Daniel Attinger
Use Of A Porous Membrane For Gas Bubble Removal In Microfluidic Channels: Physical Mechanisms And Design Criteria, Jie Xu, Regis Vaillant, Daniel Attinger
Daniel Attinger
We demonstrate and explain a simple and efficient way to remove gas bubbles from liquid-filled microchannels, by integrating a hydrophobic porous membrane on top of the microchannel. A prototype chip is manufactured in hard, transparent polymer with the ability to completely filter gas plugs out of a segmented flow at rates up to 7.4 μl/s/mm2 of membrane area. The device involves a bubble generation section and a gas removal section. In the bubble generation section, a T-junction is used to generate a train of gas plugs into a water stream. These gas plugs are then transported toward the gas removal …
Interfacial Temperature Measurements, High-Speed Visualization And Finite-Element Simulations Of Droplet Impact And Evaporation On A Solid Surface, Rajneesh Bhardwaj, Jon P. Longtin, Daniel Attinger
Interfacial Temperature Measurements, High-Speed Visualization And Finite-Element Simulations Of Droplet Impact And Evaporation On A Solid Surface, Rajneesh Bhardwaj, Jon P. Longtin, Daniel Attinger
Daniel Attinger
The objective of this work is to investigate the coupling of fluid dynamics, heat transfer and mass transfer during the impact and evaporation of droplets on a heated solid substrate. A laser-based thermoreflectance method is used to measure the temperature at the solid–liquid interface, with a time and space resolution of 100 μs and 20 μm, respectively. Isopropanol droplets with micro- and nanoliter volumes are considered. A finite-element model is used to simulate the transient fluid dynamics and heat transfer during the droplet deposition process, considering the dynamics of wetting as well as Laplace and Marangoni stresses on the liquid–gas …
A Microflow Cytometer On A Chip, Joel P. Golden, Jason Kim, George P. Anderson, Nicole N. Hashemi, Peter J. Howell, Frances S. Ligler
A Microflow Cytometer On A Chip, Joel P. Golden, Jason Kim, George P. Anderson, Nicole N. Hashemi, Peter J. Howell, Frances S. Ligler
Nastaran Hashemi
A rapid, automated, multi-analyte Microflow Cytometer is being developed as a portable, field-deployable sensor for onsite diagnosis of biothreat agent exposure and environmental monitoring. The technology relies on a unique method for ensheathing a sample stream in continuous flow past an interrogation region where optical fibers provide excitation and collect emission. This approach efficiently focuses particles in the interrogation region of the fluidic channel, avoids clogging and provides for subsequent separation of the core and sheath fluids in order to capture the target for confirmatory assays and recycling of the sheath fluid. Fluorescently coded microspheres provide the capability for highly …