Open Access. Powered by Scholars. Published by Universities.®
- Institution
- Keyword
-
- 3D Printing (1)
- Additive Manufacturing (1)
- Advanced Structures and Composites Center (1)
- Bender Element (1)
- Control (1)
-
- Discrete Element Method (1)
- Finite Element Analysis and Mesh Generation (1)
- Fracture and Cracking (1)
- Granular Material (1)
- Heterogeneous Anisotropic Materials (1)
- Homogenization (1)
- MEMS (1)
- Microfactory (1)
- Micromechanics (1)
- Microrobot (1)
- Modeling (1)
- Nonlinear Creep (1)
- Numerical Model (1)
- Simulation (1)
- Wave Velocity (1)
Articles 1 - 4 of 4
Full-Text Articles in Mechanical Engineering
Simulation Of Wave Propagation In Granular Particles Using A Discrete Element Model, Syed Tahmid Hussan
Simulation Of Wave Propagation In Granular Particles Using A Discrete Element Model, Syed Tahmid Hussan
Electronic Theses and Dissertations
The understanding of Bender Element mechanism and utilization of Particle Flow Code (PFC) to simulate the seismic wave behavior is important to test the dynamic behavior of soil particles. Both discrete and finite element methods can be used to simulate wave behavior. However, Discrete Element Method (DEM) is mostly suitable, as the micro scaled soil particle cannot be fully considered as continuous specimen like a piece of rod or aluminum. Recently DEM has been widely used to study mechanical properties of soils at particle level considering the particles as balls. This study represents a comparative analysis of Voigt and Best …
Modeling, Simulation And Control Of Microrobots For The Microfactory., Zhong Yang
Modeling, Simulation And Control Of Microrobots For The Microfactory., Zhong Yang
Electronic Theses and Dissertations
Future assembly technologies will involve higher levels of automation in order to satisfy increased microscale or nanoscale precision requirements. Traditionally, assembly using a top-down robotic approach has been well-studied and applied to the microelectronics and MEMS industries, but less so in nanotechnology. With the boom of nanotechnology since the 1990s, newly designed products with new materials, coatings, and nanoparticles are gradually entering everyone’s lives, while the industry has grown into a billion-dollar volume worldwide. Traditionally, nanotechnology products are assembled using bottom-up methods, such as self-assembly, rather than top-down robotic assembly. This is due to considerations of volume handling of large …
Development And Evaluation Of Modeling Approaches For Extrusion-Based Additive Manufacturing Of Thermoplastics, Christopher C. Bock
Development And Evaluation Of Modeling Approaches For Extrusion-Based Additive Manufacturing Of Thermoplastics, Christopher C. Bock
Electronic Theses and Dissertations
This work focuses on evaluating different modeling approaches and model parameters for thermoplastic AM, with the goal of informing more efficient and effective modeling approaches. First, different modeling approaches were tested and compared to experiments. From this it was found that all three of the modeling approaches provide comparable results and provide similar results to experiments. Then one of the modeling approaches was tested on large scale geometries, and it was found that the model results matched experiments closely. Then the effect of different material properties was evaluated, this was done by performing a fractional factorial design of experiments where …
Microstructural Analysis Of Thermoelastic Response, Nonlinear Creep, And Pervasive Cracking In Heterogeneous Materials, Alden C. Cook
Microstructural Analysis Of Thermoelastic Response, Nonlinear Creep, And Pervasive Cracking In Heterogeneous Materials, Alden C. Cook
Electronic Theses and Dissertations
This dissertation is concerned with the development of robust numerical solution procedures for the generalized micromechanical analysis of linear and nonlinear constitutive behavior in heterogeneous materials. Although the methods developed are applicable in many engineering, geological, and materials science fields, three main areas are explored in this work. First, a numerical methodology is presented for the thermomechanical analysis of heterogeneous materials with a special focus on real polycrystalline microstructures obtained using electron backscatter diffraction techniques. Asymptotic expansion homogenization and finite element analysis are employed for micromechanical analysis of polycrystalline materials. Effective thermoelastic properties of polycrystalline materials are determined and compared …