Mechanical Engineering Commons^™

Comparison Of Conventional And Adaptive Acoustic Beamforming Algorithms Using A Tetrahedral Microphone Array In Noisy Environments, Megan Brittany Ewers

Dissertations and Theses

In situ acoustic measurements are often plagued by interfering sound sources that occur within the measurement environment. Both adaptive and conventional beamforming algorithms, when applied to the outputs of a microphone array arranged in a tetrahedral geometry, are able to capture sound sources in desired directions and reject sound from unwanted directions. Adaptive algorithms may be able to measure a desired sound source with greater spatial precision, but require more calculations and, therefore, computational power. A conventional frequency-domain phase-shift algorithm and a modified adaptive frequency-domain Minimum Variance Distortionless Response (MVDR) algorithm were applied to simulated and recorded signals from a …

Thermoacoustic Refrigerator, Rees Phillip Verleur, Colleen Farrell Mccandless, Anders Matthew Bjork, Yashraj Ashwinkumar Solanki

Mechanical Engineering

In the Thermoacoustic Refrigerator Cal Poly Mechanical Engineering senior project, we designed, built, and tested a thermoacoustic refrigeration system which achieved an average temperature difference of 11.0°C. Our system consists of a resonator tube with an instrumented stack, mounted onto a base with a speaker and amplifier. An external power supply and function generator provide the power and signal to the system, and a thermocouple reader displays the temperature of the top and bottom of the stack. The system consistently achieved a significant temperature difference between the two ends of the stack in various ambient conditions, and it was quick …

Jet Engine Emissions And Vapor Contrail Reduction Through Increased Combustion Efficiency With The Aim To Mitigate Greenhouse Gases Emissions, Austin J. Brant

Honors College Theses

As society continues to globalize and advance in complexity, the increased demand for business aviation has caused the global travel rate of airlines to increase with each year. With this continual increase in aviation travel, the Federal Aviation Administration (FAA) predicts that the fuel consumption rate is to increase by 1.6 percent as of the year 2025. While this increase in fuel consumption is a positive trait of a thriving aviation community, concerns also arise regarding increased greenhouse gas emissions and enlarged contributions to the greenhouse effect. The most prevalent greenhouse gases associated with jet engine emissions are water vapor, …

Characterization Of Hydraulic Flow Noise Induced By Spool Valves, Carter A. Paprocki

Dissertations, Master's Theses and Master's Reports

The purpose of the hydraulic flow noise research was to investigate the relationship between operational valve parameters and flow noise generation. The primary consideration was correlating the flow noise generated by the valve with the distinct valve open positions. This data would allow future valve designs to account for features that cause increased flow noise and move those features away from high flow valve displacements. By implementing this, companies would be able to design quieter hydraulic systems that will not expose operators to the current levels of sound found on machines. The experiments were conducted using two valves with different …

A Dynamic Active Noise Control System For Live Music Attenuation, Elliot James Krueger

Graduate Research Theses & Dissertations

This thesis proposes a system design that will be suitable for applying active noise control (ANC) effectively to live musical instruments. The design consists of three parts: a signal separation section, an instrument classification section, and the active noise control section. The signal separation section will split up the music signals. The instrument classification section will identify the signals, and the ANC section will attenuate the music signal based on the previous information from the other sections. The two instruments of focus will be the trombone and tuba for their low frequency and ability to be quite loud in a …

A Study Of The Aeroacoustics Of Swept Propellers For Small Unmanned Aerial Vehicles, Arthur David Wiedemann

Mechanical & Aerospace Engineering Theses & Dissertations

In recent years, small unmanned aerial vehicles (UAVs) have increased in availability and use in both public and commercial sectors. This increased use of small UAVs or “drones” has the unfortunate consequence of introducing excessive noise into communities where they operate. Implementation of noise reduction methods is necessary if we wish to see expanded use of drones in public areas. With electric propulsion, the primary source of noise is the rotor/propeller used in contemporary multi-rotor configurations. In this thesis, the aerodynamics and acoustic behavior of various swept propellers is examined with computational and experimental methods.

A family of propeller geometries …

Less-Than-Lethal Self Defense Device With An Acoustic Element, Anthony Taibi

KSU Journey Honors College Capstones and Theses

This creative capstone project involves the conception, design, and creation of a less-than-lethal self defense device with an integrated sound board to control the acoustic element. Theoretically, this device is capable of deterring potential threats without causing any serious harm or any long-term damage. When starting this project, I was very focused on sonic warfare, and how to harness the power of ultrasonic and infrasonic sound waves to subdue to target; however, I concluded that using resonant frequencies to deter a human being is too dangerous, expensive, and can have negative effects for the user of the device if used …

Comparative Study And Design Of Economical Sound Intensity Probe, Karan Gundre

Dissertations, Master's Theses and Master's Reports

The theory of sound intensity measurement using the two-microphone method was first developed in the late 1970s. Even though the measurements were limited by the technology of the time, the theory was straight-forward and considerable attention was given to improving precision during testing or post-processing. With the development of modern equipment, however, the focus shifted to the apparatus. The commercial intensity probes available today have microphones that are already phase-matched. This eliminates the need for correction during or post-testing as a majority of the errors are minimized before any data is even collected. Although such intensity probes facilitate taking precise …

Optimization Of Acoustic Soundboard Through Modal Analysis And Material Selection, Noah C. Nicholas, Cody Gruber, Nicholas Hartman

Williams Honors College, Honors Research Projects

The purpose of this design project was to determine if it is plausible to design an acoustic top plate assembly made of a non-traditional material which is equivalent in sound quality to that of a standard wooden guitar. Since wood must be crafted by skilled luthiers, the overall cost of producing the completed product is fairly high. To reduce the cost of a finished acoustic guitar, we proposed to alter the material to that of one that is easier to manufacture, such as plastics and composites.

Based on our research, our team chose to test both ABS plastic and carbon …

Energy Localization And Heat Generation In Composite Energetic Systems Under High-Frequency Mechanical Excitation, Jesus O. Mares

Open Access Dissertations

In this work, the ability to use high frequency mechanical excitation to generate significant heating within plastic bonded explosives, as well as single energetic particles embedded within a viscoelastic binder, is studied. In this work, the fundamental mechanisms associated with the conversion of high-frequency mechanical excitation to heat as applied to these composite energetic systems are thoroughly investigated.

High-frequency contact excitation has been used to generate a significant amount of heat within samples of PBX 9501 and representative inert mock materials. Surface temperature rises on the order of 10 °C were observed at certain frequencies over a range from 50 …

Development Of The Compact Jet Engine Simulator From Concept To Useful Test Rig, Henry H. Haskin

Mechanical & Aerospace Engineering Theses & Dissertations

Two Compact Jet Engine Simulator (CJES) units were designed for integrated wind tunnel acoustic experiments involving a Hybrid Wing Body (HWB) vehicle. To meet the 5.8% scale of the HWB model, Ultra Compact Combustor technology from the Air Force Research Laboratory was used. The CJES units were built and integrated with a control system in the NASA Langley Low Speed Aero acoustic Wind Tunnel. The combustor liners, plug—vane and flow conditioner components were built in-house at Langley Research Center. The operation of the CJES units was mapped and fixes found for combustor instability tones and rig flow noise. The original …

Evaluation Of Angular Distribution Of Incident Field At The Transmission Loss Window In Michigan Tech’S Reverberant Chamber, Abhishek Thyagarajan

Dissertations, Master's Theses and Master's Reports

Transmission Loss prediction accuracy is highly dependent on a good understanding of the angular distribution of incident field on the panel. Traditionally, the incident field has been assumed to be either completely random (equal probability of incidence at all angles from 0° - 90°) or field incidence (where the field is assumed to be completely diffuse between 0° - 78°). Studies1-3 have shown that these models are not completely representative of the incident field. This incident field is studied in the Michigan Tech Transmission Loss suite using two different methods in this study; beamforming and acoustic intensity. The beamforming method …

The Icon Horn Loudspeaker, Vincent Phan

Mechanical Engineering

A horn loudspeaker in layperson terms is essentially taking a megaphone and integrating it into a standard speaker. Similar to a cheerleader yelling into a megaphone, the horn loudspeaker will amplify the sound from the speaker with no additional power needed. Using standard speaker horn theory, the geometry of the “megaphone” can be engineered to tune the acoustic performance tailored to loudness and/or specific acoustics frequencies. The horn contours are similar to traditional orchestra instruments such as the French horn, trumpet, and tuba. The iconic beauty of a horn married with the quantitative engineering theory creates an aesthetic yet functional …

Low Cost Flow Sensing For Field Sprayers, Yue Zhang

Theses and Dissertations--Biosystems and Agricultural Engineering

Precisely measuring the flow rate in sprayers is a key technology to precision agriculture. With the development of advanced technologies, the demand for the ability to measure flow rate of individual nozzle has become more important and urgent.

This paper investigates the possibility of developing a low-cost flow rate measurement technique. The technique is based on analyzing the acoustic signal from a microphone placed near the nozzle tip. A comparison between acoustic signal and vibration signal was made to study the relations between them. Then several possible locations of the microphone for measuring flow rate were tested and compared, and …

Developing A System For Blind Acoustic Source Localization And Separation, Raghavendra Kulkarni

Wayne State University Theses

This dissertation presents innovate methodologies for locating, extracting, and separating multiple incoherent sound sources in three-dimensional (3D) space; and applications of the time reversal (TR) algorithm to pinpoint the hyper active neural activities inside the brain auditory structure that are correlated to the tinnitus pathology. Specifically, an acoustic modeling based method is developed for locating arbitrary and incoherent sound sources in 3D space in real time by using a minimal number of microphones, and the Point Source Separation (PSS) method is developed for extracting target signals from directly measured mixed signals. Combining these two approaches leads to a novel technology …

Simulation Of Whistle Noise Using Computational Fluid Dynamics And Acoustic Finite Element Simulation, Jiawei Liu

Theses and Dissertations--Mechanical Engineering

The prediction of sound generated from fluid flow has always been a difficult subject due to the nonlinearities in the governing equations. However, flow noise can now be simulated with the help of modern computation techniques and super computers. The research presented in this thesis uses the computational fluid dynamics (CFD) and the acoustic finite element method (FEM) in order to simulate the whistle noise caused by vortex shedding. The acoustic results were compared to both analytical solutions and experimental results to better understand the effects of turbulence models, fluid compressibility, and wall boundary meshes on the acoustic frequency response. …

Dolphin Sound Production And Distribution On The West Florida Shelf, Peter Simard

USF Tampa Graduate Theses and Dissertations

This dissertation is an investigation of dolphin sound production and distribution off west central Florida. Although a wealth of information exists on the production of common sounds (whistles, echolocation) made by captive, trained dolphins, far less is known about free-ranging dolphin sound production and of unusual sounds. In addition, while inshore dolphin populations or communities are the subjects of research projects in many locations, dolphins in offshore waters are less commonly studied. The objectives of this dissertation were to contribute information on free-ranging dolphin sounds and continental shelf dolphin distribution.

While echolocation has been rigorously studied in captive, trained dolphins, …

The Effect Of Static Pressure On The Inertial Cavitation Threshold And Collapse Strength, Kenneth Bryan Bader

Electronic Theses and Dissertations

The amplitude of the acoustic pressure required to nucleate a gas and/or vapor bubble in a fluid, and to have that bubble undergo an inertial collapse, is termed the inertial cavitation threshold. The hydrostatic dependence of the inertial cavitation threshold was measured up to 30 MPa in ultrapure water using a high quality factor spherical resonator. The threshold increased linearly with the hydrostatic pressure and was found to be temperature dependent. The strength of the bubble collapse at the threshold was measured in terms of shock waves and light emissions. The shock amplitudes increased linearly with the hydrostatic pressure, while …

Elastic And Magnetic Properties Of Tb6fe(Sb,Bi)2 Using Resonant Ultrasound Spectroscopy., David Michael Mccarthy

Masters Theses

Tb6FeSb2 and Tb6FeBi2 are novel rare earth compounds with little prior research. These compounds show high and variable curie temperatures for rare-earth compounds. This has lead to a literature review which includes the discussion of: elasticity, resonance, and magnetism. This review is used to discuss the theory and methodology which can relate these various properties to each other. Furthermore, synthesis, x-ray analysis, and RUS sample preparation of Tb6FeSb2 and Tb6FeBi2 were completed.

Resonant Ultrasound Spectroscopy (RUS) elastic studies were taken for Tb6FeSb2 and Tb6FeBi2 as a function temperature from 5-300K, in various magnetic fields ranging from 0-9T. Tb6FeSb2’s and Tb6FeBi2’s …

The Solution Of Hypersingular Integral Equations With Applications In Acoustics And Fracture Mechanics, Richard S. St. John

Mathematics & Statistics Theses & Dissertations

The numerical solution of two classes of hypersingular integral equations is addressed. Both classes are integral equations of the first kind, and are hypersingular due to a kernel containing a Hadamard singularity. The convergence of a Galerkin method and a collocation method is discussed and computationally efficient algorithms are developed for each class of hypersingular integral equation.

Interest in these classes of hypersingular integral equations is due to their occurrence in many physical applications. In particular, investigations into the scattering of acoustic waves by moving objects and the study of dynamic Griffith crack problems has necessitated a computationally efficient technique …

Analysis Of Random Structure-Acoustic Interaction Problems Using Coupled Boundary Element And Finite Element Methods, Carl S. Pates Iii

Mechanical & Aerospace Engineering Theses & Dissertations

A coupled boundary element(BEM)-finite element(FEM) approach is presented to accurately model structure-acoustic interaction systems. The boundary element method is first applied to interior, two and three-dimensional acoustic domains with complex geometry configurations. Boundary element results are very accurate when compared with limited exact solutions.

Structure-interaction problems are then analyzed with the coupled FEM-BEM method, where the finite element method models the structure and the boundary element method models the interior acoustic domain. The coupled analysis is compared with exact and experimental results for a simplistic model. Composite panels are analyzed and compared with isotropic results. The coupled method is then …

Binaural Room Simulation, Brian A. Smith

Theses and Dissertations

Research in binaural and spatial hearing is of particular interest to the Air Force. Applications in cockpit communication, target recognition, and aircraft navigation are being explored. This thesis examines human auditory localization cues and develops a mathematical model for the transfer function of a sound signal traveling from an isotropic point source through a rectangular room to both ears of a listener. Using this model as a guide, non-head coupled binaural sound signals are generated in a binaural room simulation. Reflection and attenuation cues included in the computer generated signals are varied in order to determine which cues enhance the …