Materials Science and Engineering Commons^™

Development Of Cost-Effective High-Modulus Asphalt Concrete (Hmac) Mixtures Using Crumb Rubber And Local Construction Materials In Louisiana., Ibrahim A.I.E Elnaml

LSU Master's Theses

One of the emerging solutions to enhance the durability of asphalt pavements is the use of a French asphalt mix known as “High-Modulus Asphalt Concrete (HMAC).” This mix uses a hard asphalt binder, high binder content (about 6%), and low air voids content as compared to Superpave mixtures. The key objective of this study was to develop a cost-effective HMAC mixture using crumb rubber and local materials in Louisiana. To achieve this objective, four HMAC mixtures were prepared using two asphalt binders (PG 82-22 and PG 76-22 plus 10% crumb rubber) and two Reclaimed Asphalt Pavement (RAP) contents (20% and …

Growth, Characterization, And Mechanical Testing Of Diamond-Like Carbon Films, Tailei Qi

LSU Master's Theses

The high residual stresses within diamond-like carbon (DLC) films limit its thickness and make the film tend to delaminate from the substrate and be defective on the surface. To address this problem, a new plasma enhanced chemical vapor deposition system (PECVD) was set up to investigate the effects of different film growth parameters on the DLC films, such as chromium doping, gas fluxes, depositing pressures, bias voltages, and depositing times. After the film growth parameters were optimized, this condition was transferred from silicon wafer to SS316 steel plate to deposition of DLC films with some adjustments. Scanning electron microscopy (SEM) …

Degumming Of Hemp Fibers Using Combined Microwave Energy And Deep Eutectic Solvent, Bulbul Ahmed

LSU Master's Theses

Hemp is considered as one of the sustainable agricultural fiber materials. Degumming or surface modification of hemp bast is needed to produce single fibers for ensuing textile and industrial applications. The traditional degumming process necessitates a high amount of alkali, which causes detrimental environmental pollution. This study offers a new method to degum hemp fibers with reduced use of harmful alkali and precious water resources. In this work, hemp bast fibers were degummed by using combined microwave energy and deep eutectic solvent (DES). The properties of hemp fibers manufactured by this method were investigated and compared with the traditional alkali …

An Investigation Of High-Speed Consolidation And Repair Of Carbon Fiber - Epoxy Composites Through Ultrasonic Welding, David A. Hoskins

LSU Master's Theses

Adhesive repair of carbon fiber composite structures is commonly done on damaged structures to extend the service life. This method requires careful preparation of the damaged surface with intricate steps to ensure good bonding between the repair patch and the parent structure by means of an adhesive film. As with many forms of composite manufacturing, it is required to perform vacuum bagging, debulking, and a heated cure depending on the resin. All these steps make the repair process costly and time consuming.

In this present work, an alternative method of repair is investigated which explores the experimental feasibility of using …

Concentration Flow Cells For Efficient Salinity Energy Recovery With Carbonized Peat Moss And Molybdenum Disulfide Electrodes, Haihui Zhu

LSU Master's Theses

The globally extractable salinity gradient (SG) energy from the mixing of seawater and river water is estimated to be 3% of worldwide electricity consumption. Here we applied carbonized peat moss (CPM) electrodes and molybdenum disulfide (MoS₂) electrodes to a concentration flow cell that is capable of harvesting SG energy based on the electrode (pseudo-)capacitance together with the Donnan potential. The CPM electrodes were made from the visually inexhaustible peat moss by a facile pyrolysis process. With two identical CPM electrodes and a cation-exchange membrane, the cell produced a peak power density of 5.33 W m^-2 and an …

Waste Management By Waste: Removal Of Acid Dyes From Wastewaters Of Textile Coloration Using Fish Scales, S M Fijul Kabir

LSU Master's Theses

Removal of hazardous acid dyes by economical process using low-cost bio-sorbents from wool industry wastewaters is of a pressing need, since it causes skin and respiratory diseases and disrupts other environmental components. Fish scales (FS), a by-product of fish industry, a type of solid waste, are usually discarded carelessly resulting in pungent odor and environmental burden. In this research, the FS of black drum (Pogonias cromis) were used for the removal of acid dyes (acid red 1 (AR1), acid blue 45 (AB45) and acid yellow 127 (AY126)) from wool industry wastewaters by absorption process with a view to …