Materials Science and Engineering Commons^™

Influence Of The Temperature On Flow-Induced Crystallization Of Isotactic Polypropylene And Propylene-Ethylene Random Copolymer, Hugo Boitout

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

When flow is applied on a semi-crystalline polymer melt, it can greatly impact how it crystallizes its final properties. Therefore, it is crucial to understand the basic mechanism of flow induced crystallization (FIC). Only then will it be possible to predict final properties from the type of resin and processing conditions. Polypropylene is one of the most widely used polymers. Its processing generally involves subjecting the melt to intense flow fields, so FIC commonly occurs.

This study investigates the influence of temperature of shear and crystallization on the FIC behavior of isotactic polypropylene (iPP). Temperature is one of the main …

Low Molecular Weight Glucosamine/L-Lactide Copolymers As Potential Carriers For The Development Of A Sustained Rifampicin Release System: Mycobacterium Smegmatis As A Tuberculosis Model, Jorge Ragusa

Department of Chemical and Biomolecular Engineering: Theses and Student Research

Tuberculosis, a highly contagious disease, ranks as the second leading cause of death from an infectious disease, and remains a major global health problem. In 2013, 9 million new cases were diagnosed and 1.5 million people died worldwide from tuberculosis. This dissertation aims at developing a new, ultrafine particle-based efficient antibiotic delivery system for the treatment of tuberculosis. The carrier material to make the rifampicin (RIF)-loaded particles is a low molecular weight star-shaped polymer produced from glucosamine (molecular core building unit) and L-lactide (GluN-LLA). Stable particles with a very high 50% drug loading capacity were made via electrohydrodynamic atomization. Prolonged …

Microstructure And Magnetic Behavior Studies Of Processing-Controlled And Composition-Modified Fe-Ni And Mn-Al Alloys, Yunlong Geng

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

L1₀-type (Space group P4/mmm) magnetic compounds, including FeNi and MnAl, possess promising technical magnetic properties of both high magnetization and large magnetocrystalline anisotropy energy, and thus offer potential in replacing rare earth permanent magnets in some applications.

In equiatomic Fe-Ni, the disorder-order transformation from fcc structure to the L1₀ structure is a diffusional transformation, but is inhibited by the low ordering temperature. The transformation could be enhanced through the creation of vacancies. Thus, mechanical alloying was employed to generate more open-volume defects. A decrease in grain size and concomitant increase in grain boundary area resulted from …

Fabrication Of 3d Ultrafine Fibrous Protein Structures Via Freeze-Drying, Yiling Huang

Department of Textiles, Merchandising, and Fashion Design: Dissertations, Theses, and Student Research

In this thesis, ultrafine fibrous 3D matrices were fabricated using three different proteins (soy protein, wool keratin, and chicken feather keratin) via freeze-drying. Protein matrices are preferable for tissue engineering compared to matrices made from synthetic material because of their similarity to native extracellular matrices. Due to their cell-binding motifs, natural proteins are also recognized as more biocompatible compared. Freeze-drying, which is a simple method used to produce 3D sponge matrices, was employed in this study to fabricate 3D fibrous matrices in a controlled manner. The inner structures of the 3D matrices fabricated ranged from film to fibers, and the …

Opto-Electronic Devices With Nanoparticles And Their Assemblies, Chieu Van Nguyen

Department of Chemical and Biomolecular Engineering: Theses and Student Research

Nanotechnology is a fast growing field; engineering matters at the nano-meter scale. A key nanomaterial is nanoparticles (NPs). These sub-wavelength (< 100nm) particles provide tremendous possibilities due to their unique electrical, optical, and mechanical properties. Plethora of NPs with various chemical composition, size and shape has been synthesized. Clever designs of sub-wavelength structures enable observation of unusual properties of materials, and have led to new areas of research such as metamaterials. This dissertation describes two self-assemblies of gold nanoparticles, leading to an ultra-soft thin film and multi-functional single electron device at room temperature. First, the layer-by-layer self-assembly of 10nm Au nanoparticles and polyelectrolytes is shown to behave like a cellular-foam with modulus below 100 kPa. As a result, the composite thin film (~ 100nm) is 5 orders of magnitude softer than an equally thin typical polymer film. The thin film can be compressed reversibly to 60% strain. The extraordinarily low modulus and high compressibility are advantageous in pressure sensing applications. The unique mechanical properties of the composite film lead to development of an ultra-sensitive tactile imaging device capable of screening for breast cancer. On par with human finger sensitivity, the tactile device can detect a 5mm imbedded object up to 20mm below the surface with low background noise. The second device is based on a one-dimensional (1-D) self-directed self-assembly of Au NPs mediated by dielectric materials. Depending on the coverage density of the Au NPs assembly deposited on the device, electronic emission was observed at ultra-low bias of 40V, leading to low-power plasma generation in air at atmospheric pressure. Light emitted from the plasma is apparent to the naked eyes. Similarly, 1-D self-assembly of Au NPs mediated by iron oxide was fabricated and exhibits ferro-magnetic behavior. The multi-functional 1-D self-assembly of Au NPs has great potential in modern electronics such as solid state lighting, plasma-based nanoelectronics, and memory devices.

Adviser: Ravi F. Saraf

Low Noise, High Detectivity Photodetectors Based On Organic Materials, Fawen Guo

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Organic photodetectors (OPDs) are potentially useful in many applications because of their light weight, flexibility and good form factors. Despite the high detectivities that have been frequently reported for OPDs recently, the application of these OPDs for weak light detection has been rarely demonstrated.

In this thesis, low noise, high gain photodetectors based on organic and ZnO nanoparticles were proposed and demonstrated for highly sensitive UV light detection. The nanocomposite photodetector works in a hybrid mode of photodiode and photoconductor with the transition controlled by the UV light illumination. The nanocomposite detector shows two orders of magnitude higher sensitivity than …

Structural, Magnetic And Microstructural Studies Of Composition-Modified Sm-Co Ribbons, Xiujuan Jiang

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

There is an increasing interest in developing desirable microstructures in hard magnetic materials. Sm-Co-based magnets, bearing superior intrinsic magnetic properties, are good candidates for further development. Two Sm-Co-based alloys, (Sm₁₂Co₈₈)_100-x-yCr_yC_x (taking SmCo₇ phase) and SmCo_4-xFe_xB (a derivative of SmCo₅ phase), were produced using melt-spinning technique. The magnetic properties are correlated to the structural and microstructural properties.

Within the SmCo₇ stoichiometry, cumulative effects of Cr and C additions on the structural and magnetic properties have been investigated. Experimental results have shown that these additions along …

Large-Scale Solution Synthesis Of Narrow Graphene Nanoribbons, Timothy H. Vo, Mikhail Shekhirev, Donna A. Kunkel, Martha D. Morton, Eric Berglund, Lingmei Kong, Peter M. Wilson, Peter A. Dowben, Axel Enders, Alexander Sinitskii

Nebraska Center for Materials and Nanoscience: Faculty Publications

According to theoretical studies, narrow graphene nanoribbons with atomically precise armchair edges and widths of(1.1 eV), which makes them potentially promising for logic applications. Different top–down fabrication approaches typically yield ribbons with width >10nm and have limited control over their edge structure. Here we demonstrate a novel bottom–up approach that yields gram quantities of high-aspect-ratio graphene nanoribbons, which are only ~1 nm wide and have atomically smooth armchair edges. These ribbons are shown to have a large electronic bandgap of ~1.3 eV, which is significantly higher than any value reported so far in experimental studies of graphene nanoribbons prepared by …

Organic Ferroelectric Evaporator With Substrate Cooling And In Situ Transport Capabilities, Keith Foreman, C. Labedz, M. Shearer, Shireen Adenwalla

Shireen Adenwalla Papers

We report on the design, operation, and performance of a thermal evaporation chamber capable of evaporating organic thin films. Organic thin films are employed in a diverse range of devices and can provide insight into fundamental physical phenomena. However, growing organic thin films is often challenging and requires very specific deposition parameters. The chamber presented here is capable of cooling sample substrates to temperatures below 130 K and allows for the detachment of the sample from the cooling stage and in situ transport. This permits the use of multiple deposition techniques in separate, but connected, deposition chambers without breaking vacuum …

Practical Aspects Of Modern And Future Permanent Magnets, R.W. Mccallum, L. H. Lewis, Ralph Skomski, M. J. Kramer, I. E. Anderson

Ralph Skomski Publications

The mandate to reduce greenhouse gases will require highly efficient electric machines for both power generation and traction motor applications. Although permanent magnet electric machines utilizing Nd2Fe14B-based magnets provide obvious power-to-weight advantages over induction machines, the limited availability and high price of the rare earth (RE) metals make these machines less favorable. Of particular concern is the cost and supply criticality of Dy, a key RE element that is required to improve the high-temperature performance of Nd-based magnetic alloys for use in generators and traction motors. Alternatives to RE-based alloys do exist, but they currently lack the energy density necessary …

Agen/Bsen 344: Biological And Environmental Transport Processes—A Peer Review Of Teaching Project Benchmark Portfolio, Shadi F. Othman

UNL Faculty Course Portfolios

The course I am providing a portfolio for is BSEN/AGEN 344 which is a required course for all our undergraduate students. The Department provides an assessment for the course to align itself with the ABET's Accreditation Process. I taught the course in Spring 2012 adapting a new Team Based Learning Approach. I have three main objective from my portfolio: (1) refine my methods in documenting the linkage between my course goals and assessment measures, (2) document the efficacy of team based learning approach, (3) refine team based learning approach for the current course and adapt the approach to future courses, …

Effect Of Er Doping On The Structural And Magnetic Properties Of Cobalt-Ferrite, Sateesh Prathapani, M. Vinitha, Tanjore V. Jayaraman, D. Das

Department of Mechanical and Materials Engineering: Faculty Publications

Nanocrystalline particulates of Er doped cobalt-ferrites CoFe_(2–x)Er_xO₄ (0 ≤ x ≤ 0.04), were synthesized, using sol-gel assisted autocombustion method. Co-, Fe-, and Er- nitrates were the oxidizers, and malic acid served as a fuel and chelating agent. Calcination (400–600 °C for 4h) of the precursor powders was followed by sintering (1000 °C for 4 h) and structural and magnetic characterization. X-ray diffraction confirmed the formation of single phase of spinel for the compositions x = 0, 0.01, and 0.02; and for higher compositions an additional orthoferrite phase formed along with the spinel phase. …

Introduction To Special Issue Of Journal Of Defense Modeling And Simulation: Novel Approaches To Defense And Military Modeling And Simulation, Scott D. Snyder, James M. Taylor Jr

Peter Kiewit Institute: Faculty Publications

Developing solutions to complex problems in government and industry is a daunting task that often requires tremendous investment in time and resources to solve. Modeling and simulation (M&S) has incredible potential to streamline development and cut costs by conducting virtual experiments that give insight into performance under various test conditions. As many program managers in the federal acquisition process can attest, realistic testing of live equipment in an operational environment can be some of the most expensive parts of a development program. M&S can provide insight into mission success of yetto- bedesigned systems without the need to actually build and …

Simple Multi-Attribute Rating Technique For Renewable Energy Deployment Decisions (Smart Redd), James M. Taylor Jr, Betty Love

Peter Kiewit Institute: Faculty Publications

In the effort to provide electrical power service and the sustaining fuel required to run generators at forward-deployed bases in Afghanistan and Iraq over more than 10 years, the US military spent billions of dollars and a paid a heavy toll in terms of human casualties. The green energy linear program for optimizing deployments (GELPOD) proof-of-concept model showed that a linear program could be used to optimize combat deployment of energy generation systems to minimize cost and casualties. Results indicated that reduction in both cost and casualties for renewable energy sources was highly dependent on fuel cost and deployment length. …