Materials Science and Engineering Commons^™

Decarbonizing Rural Residential Buildings In Cold Climates: A Techno-Economic Analysis Of Heating Electrification, Filippo Padovani, Nelson Sommerfeldt, Francesca Longobardi, Joshua M. Pearce

Michigan Tech Publications

Given the need for decarbonization of the heating sector and the acute need of a propane replacement in the U.S. Upper Midwest, this study quantifies the techno-economic characteristics of sustainable heating electrification in isolated rural, residential buildings in cold climates without natural gas supply. Archetypal buildings are modeled under four levels of electrification. At each electrification level, a parametric solar photovoltaic (PV) sizing analysis is performed and the total life cycle cost, renewable fraction and greenhouse gas (GHG) emissions are calculated based on the primary energy supply for each building type. Cost optimal solutions are stress-tested with multi-dimensional sensitivity analyses. …

Economics Of Grid-Tied Solar Photovoltaic Systems Coupled To Heat Pumps: The Case Of Northern Climates Of The U.S. And Canada, Joshua M. Pearce, Nelson Sommerfeldt

Michigan Tech Publications

Solar photovoltaic (PV) technology is now a profitable method to decarbonize the grid, but if catastrophic climate change is to be avoided, emissions from transportation and heating must also decarbonize. One approach to renewable heating is leveraging improvements in PV with heat pumps (HPs). To determine the potential for PV+HP systems in northern areas of North America, this study performs numerical simulations and economic analysis using the same loads and climate, but with local electricity and natural gas rates for Sault Ste. Marie, in both Canada and U.S. Ground-mounted, fixed-tilt, grid-tied PV systems are sized to match 100% of electric …

Water Conservation Potential Of Self-Funded Foam-Based Flexible Surface-Mounted Floatovoltaics, Kaomi Soulemane Hayibo, Pierce Mayville, Ravneet Kaur Kailey

Michigan Tech Publications

A potential solution to the coupled water–energy–food challenges in land use is the concept of floating photovoltaics or floatovoltaics (FPV). In this study, a new approach to FPV is investigated using a flexible crystalline silicon-based photovoltaic (PV) module backed with foam, which is less expensive than conventional pontoon-based FPV. This novel form of FPV is tested experimentally for operating temperature and performance and is analyzed for water-savings using an evaporation calculation adapted from the Penman–Monteith model. The results show that the foam-backed FPV had a lower operating temperature than conventional pontoon-based FPV, and thus a 3.5% higher energy output per …

Open Source Low-Cost Power Monitoring System, Shane W. Oberloier, Joshua M. Pearce

Department of Materials Science and Engineering Publications

This study presents an entirely open-source, low-cost power monitoring system capable of many types of measurements including both loads and supplies such as solar photovoltaic systems. In addition, the system can be fabricated using only open source software and hardware. The design revolves around the Digital Universal Energy Logger (DUEL) Node, which is responsible for reading and properly scaling the voltage and current of a particular load, and then serializing it via an on-board ATTiny85 chip. The configuration of the DUEL node allows for custom sensitivity ranges, and can handle up to 50 A and 300 V. Up to 127 …

General Design Procedures For Airport-Based Solar Photovoltaic Systems, Anurag Anurag, Jiemin Zhang, Jephias Gwamuri, Joshua M. Pearce

Department of Materials Science and Engineering Publications

A source of large surface areas for solar photovoltaic (PV) farms that has been largely overlooked in the 13,000 United States of America (U.S.) airports. This paper hopes to enable PV deployments in most airports by providing an approach to overcome the three primary challenges identified by the Federal Aviation Administration (FAA): (1) reflectivity and glare; (2) radar interference; and (3) physical penetration of airspace. First, these challenges and precautions that must be adhered to for safe PV projects deployment at airports are reviewed and summarized. Since one of the core concerns for PV and airport symbiosis is solar panel …

Fabricating Ordered 2-D Nano-Structured Arrays Using Nanosphere Lithography, Chenlong Zhang, Sandra Cvetanovic, Joshua M. Pearce

Department of Materials Science and Engineering Publications

Recent advances in the use of plasmonic metamaterials to improve absorption of light in thin-film solar photovoltaic devices has created a demand for a scalable method of patterning large areas with metal nanostructures deposited in an ordered array. This article describes two methods of fabricating ordered 2D nanosphere colloidal films: spin coating and interface coating. The two methods are compared and parameter optimization discussed. The study reveals that:

• For smaller nanosphere sizes, spin coating is more favorable, while for larger nanospheres, the angled interface coating provides more coverage and uniformity.

• A surfactant-free approach for interface coating is developed …

High-Efficiency Solar-Powered 3-D Printers For Sustainable Development, Jephias Gwamuri, Dhiogo Franco, Khalid Khan, Lucia Gauchia, Joshua M. Pearce

Michigan Tech Publications

The release of the open source 3-D printer known as the RepRap (a self-Replicating Rapid prototyper) resulted in the potential for distributed manufacturing of products for significantly lower costs than conventional manufacturing. This development, coupled with open source-appropriate technology (OSAT), has enabled the opportunity for 3-D printers to be used for sustainable development. In this context, OSAT provides the opportunity to modify and improve the physical designs of their printers and desired digitally-shared objects. However, these 3-D printers require electricity while more than a billion people still lack electricity. To enable the utilization of RepRaps in off-grid communities, solar photovoltaic …