Open Access. Powered by Scholars. Published by Universities.®

Engineering Science and Materials Commons™

Open Access. Powered by Scholars. Published by Universities.®

2004

Chemistry

Journal of Electrochemistry

Articles 1 - 30 of 50

Full-Text Articles in Engineering Science and Materials

Electrochemical Behaviours Of Hemoglobin-Ddab-Modified Powder Microelectrode And The Application Of The Powder Microelectrode In Determination Of Nitric Oxide, Zhi-Mou Guo, Huan Liu, Jian Chen, Wen-Ting Zhang Nov 2004

Electrochemical Behaviours Of Hemoglobin-Ddab-Modified Powder Microelectrode And The Application Of The Powder Microelectrode In Determination Of Nitric Oxide, Zhi-Mou Guo, Huan Liu, Jian Chen, Wen-Ting Zhang

Journal of Electrochemistry

The electrochemical behaviours of DDAB-Hb-PME were studied in this paper. The (apparent) surface concentration of Hb was enhanced greatly by using the powder microelectrode (technique). NO reacts with Hb and absorbs on the surface of the modified carbon powder. Therefore, the output of the electrode was enhanced greatly by employing PME with higher reaction surface (area). The sensitivity of DDAB-Hb-PME is 3.1 mA/μmol·L~(-1)·cm~(2), which is much larger than the values obtained with the traditional electrodes. The detection limit is 9 nmol·L~(-1) and the linear response range is 9～100 nmol·L~(-1).

Go to article

Lico_(X)Ni_(1-X)O_2 Cathode Materials Prepared By Electrolysis Of Co And Ni, Jin-Ping Wei, Xin Sun, Xiao-Yu Wang, Xi-Kui Bian, Jin-Ling Zhai, Yan-Jie Yan-Jie Nov 2004

Lico_(X)Ni_(1-X)O_2 Cathode Materials Prepared By Electrolysis Of Co And Ni, Jin-Ping Wei, Xin Sun, Xiao-Yu Wang, Xi-Kui Bian, Jin-Ling Zhai, Yan-Jie Yan-Jie

Journal of Electrochemistry

A new electrolytic method was developed to prepare LiCo_(x)Ni_(1-x)O_2 as a cathode material of lithium-ion battery. Contrary to the traditional method, electrolytic method is a potential method with simple process to industrialization and no pollution. Metal cobalt and nickel were electrolysed in parallel to prepare the precursor of Co_( x )Ni_(1- x )(OH)_2.Different compositional precursors could be conveniently prepared by changing electrolytic current. The LiCo_(0.3)Ni_(0.7)O_2 cathode prepared by this method was found favorable charge-discharge and cycle properties. For the LiCo_(0.3)Ni_(0.7)O_(2 )cathode material, the discharge capacities in the 1st and 50th cycles were 163 mAh/g and 140 mAh/g with charge retention …

Go to article

The Investigation Of Bafesi/C Alloy Composite As Anode Materials For Li-Ion Battery, Rui-Xiang Feng, Hua Dong, Xin-Ping Ai, Han-Xi Yang Nov 2004

The Investigation Of Bafesi/C Alloy Composite As Anode Materials For Li-Ion Battery, Rui-Xiang Feng, Hua Dong, Xin-Ping Ai, Han-Xi Yang

Journal of Electrochemistry

A novel BaFeSi/C composite was prepared by mechanical ball milling, and lithium insertion reactions on the composite electrode were investigated by cyclic voltammetry ,charge-discharge measurements, XRD and XPS spectroscopy. It is demonstrated that the capacity retention with indiscernible capacity decas during charge-discharge cycling. The improved cycling ability of the composite is suggested from a cooperative action by inactive FeSi_(2 )and BaSi_2 matrix and outer graphite shell, which both buffer the volumetric changes of the active Si phase and provide a good connection for electronic and ionic conduction during lithium insertion and extraction processes.

Go to article

Electrocatalytic Performances Of Carbon Nanotube Air Electrode For Oxygen Reduction, Feng-Ming Zhao, Chun-An Ma Nov 2004

Electrocatalytic Performances Of Carbon Nanotube Air Electrode For Oxygen Reduction, Feng-Ming Zhao, Chun-An Ma

Journal of Electrochemistry

The air electrodes with different mass ratio of Pt/active carbon or carbon nanotube as catalyst layer material have been prepared. The electrocatalytic performances for oxygen reduction were evaluated by means of polarization curve and electrochemical impedance spectroscopy (EIS). The results disclosed that carbon nanotubes dealt with nitric acid in the catalyst layer had been improved obviously on the electrocatalytic activity. After the surface of carbon nanotube was oxygenated and aggraded with platinum, the catalyst had obviously effects on the electrocatalytic activity. The air electrode with the mass ratio of active carbon to Pt/carbon nanotube in 4∶1 showed better electrocatalytic activity, …

Go to article

Electrochemical Investigations On Pitting Susceptibility Of Iron-Based Alloy, Wei-Shan Li, Hong-Yu Chen, Zhong-Zhi Yuan, Hong Li, Qi-Ming Huang, Dong-Sheng Lv Nov 2004

Electrochemical Investigations On Pitting Susceptibility Of Iron-Based Alloy, Wei-Shan Li, Hong-Yu Chen, Zhong-Zhi Yuan, Hong Li, Qi-Ming Huang, Dong-Sheng Lv

Journal of Electrochemistry

The formation process of passive film on iron and electronic properties and pitting susceptibility of an iron-based alloy are investigated by using linear potential sweep, alternative current impedance and electrochemical nose technologies. The relationship between reciprocal square capacitance and potential following the Mott-Schottky behavior is limited at a narrow rang of low potentials. At higher potentials, linear relationship between reciprocal capacitance and potential is obtained, which is ascribed to the increasing thickness of the passive film with potential. The donor density of the passive film is influenced by the formation potential of the film, passivator and microstructure. The decrease in …

Go to article

Preparation And Electrochemical Magnesium Insertion Behaviors Of Mgv_2o_6, Hua-Tang Yuan, Li-Fang Jiao, Jian-Sheng Cao, Xiu-Sheng Liu, Ming Zhao, Yong-Mei Wang Nov 2004

Preparation And Electrochemical Magnesium Insertion Behaviors Of Mgv_2o_6, Hua-Tang Yuan, Li-Fang Jiao, Jian-Sheng Cao, Xiu-Sheng Liu, Ming Zhao, Yong-Mei Wang

Journal of Electrochemistry

MgV_2O_6was synthesized by conventional solid-state reaction from MgO and V_2O_(5)as starting materials. X-Ray diffraction analysis showed that the prepared sample belongs to the monoclinic structure. Electrochemical magnesium insertion from aprotic electrolytes such as organomagnesium halides into this host was found possible and exhibited charge/discharge circulation.

Go to article

Studies On The Electrochemical Preparation And Electrochemical Properties Of Conducting Polymers——Brief Introduction To The Research Work Of Electrochemistry Of Conducting Polymers In Cas Key Laboratory Of Organic Solids(I), Yong-Fange Academy Of Sciences Li Nov 2004

Studies On The Electrochemical Preparation And Electrochemical Properties Of Conducting Polymers——Brief Introduction To The Research Work Of Electrochemistry Of Conducting Polymers In Cas Key Laboratory Of Organic Solids(I), Yong-Fange Academy Of Sciences Li

Journal of Electrochemistry

Conducting polymers have drawn much attention since the discovery of conducting polyacetylene in 1977, due to the novelty and curiosity of their structure and properties as well as their promising applications in many aspects. Among the studies of conducting polymers, the electrochemical preparation and electrochemical properties of conducting polymers are of special importance, because the electropolymerization is a main method for preparing conducting polymer films and the electrochemical properties are the basis for their applications in the fields of electrode materials for batteries, electrocatalysis, electrochromic display, etc. We are one of the earliest research groups in the world to perform …

Go to article

Preparation And Photo-Catalyst Properties Of The Α-Fe_2o_3-Tio_2 Films On Sodium Alginate Polymer, Li-Qin Chen, Huai-Zhen Zhong, Ri-Yao Chen, Xi Zheng, Zhen Chen Nov 2004

Preparation And Photo-Catalyst Properties Of The Α-Fe_2o_3-Tio_2 Films On Sodium Alginate Polymer, Li-Qin Chen, Huai-Zhen Zhong, Ri-Yao Chen, Xi Zheng, Zhen Chen

Journal of Electrochemistry

Three new nano thin films of α-Fe_2O_(3)、TiO_2 and α-Fe_2O_(3)-TiO_2 by doping their powder with sodium alginate polymer were prepared. Surface structure and catalytic activities of the films were characterized by FTIR、XRD、PL、TEM and I-V techniques. The results of UV-visible absorption showed that the methylene blue was mineralized in aqueous of α-Fe_2O_(3)/SA、TiO_2/SA and (α-(Fe_2O_(3)))-TiO_2 /SA upon radiation with ultra violet light. α-Fe_2O_(3) enhanced their photo-decolorized-activities by doping 15% TiO_2.

Go to article

Applications Of New Activated Carbon Meterials In The Electric Double-Layer Capacitor, Jian-Jun Zhang Nov 2004

Applications Of New Activated Carbon Meterials In The Electric Double-Layer Capacitor, Jian-Jun Zhang

Journal of Electrochemistry

A new type activated carbon whose precursor was coconut shell could be obtained using specific physics-chemistry activation, and the activated carbon was applied as the material of electrode in EDLC(electrical double-layer capacitor),which had a large specific capacitance,and could charge and discharged in some large currents. Carbon dioxide and acid were used to modify carbon,and the effects of post-treatment on surface area and pore volume were investigated. A moulding method which has influence on some properties of carbon electrode with PTFE additive was researched in the paper.

Go to article

Improvement And Its Mechanism Of Storage Performance Of Ni-Mh Battery, Xiao-Feng Li Nov 2004

Improvement And Its Mechanism Of Storage Performance Of Ni-Mh Battery, Xiao-Feng Li

Journal of Electrochemistry

The storage performance of nickel-metal-hydride (Ni-MH) battery was studied by using galvanostatic charge-discharge and cyclic voltammetry. The experimental results indicated that CoOOH could not be completely restored after its being thoroughly reduced at lower potential, which might weaken electric conduction network in the positive electrode and result in fading of electrochemical properties of Ni-MH battery. Addition of nickel powder as a conductive agent into the positive electrode was beneficial to the capacity recovery after storage.

Go to article

Effect Of Fe~(3+) Dopen Of Titanium Dioxide Film On Absorption Spectra And Photo Catalysis, Mei-Qun Xiao, Jia-Nian Shen, Moucheng Li, Peng-Fei Wu, Dong Liu, Yu-Juan Zhang Nov 2004

Effect Of Fe~(3+) Dopen Of Titanium Dioxide Film On Absorption Spectra And Photo Catalysis, Mei-Qun Xiao, Jia-Nian Shen, Moucheng Li, Peng-Fei Wu, Dong Liu, Yu-Juan Zhang

Journal of Electrochemistry

Photo-catalytic titanium dioxide film in nano crystalline has been prepared by electrochemical oxidation process and adding different amount of ferric ion into the electrolyte during the anodic oxidation.The effects of Fe~(3+) dopen on absorption spectra and photo-catalytic of the titanium dioxide films have been studied. It shows that the Fe~(3+) dopen caused the red shife of the absorption edge for the incoming light and exhibited the improved photocatalytic reactivity.

Go to article

Study On Mass Transport In Liquid Layer Adjacent To The Electrode Through Transmission Vop-Spectroellipsometry, Wei Zhu, Yangyu-Ru Yangyu-Ru, Zong-Qing Huang Nov 2004

Study On Mass Transport In Liquid Layer Adjacent To The Electrode Through Transmission Vop-Spectroellipsometry, Wei Zhu, Yangyu-Ru Yangyu-Ru, Zong-Qing Huang

Journal of Electrochemistry

In electrochemical system, the mass transport process in liquid layer adjacent to electrode is studied through theoretical analysis only.The diffusion process can be analyzed theoretically by Fick's law for homogeneous media. Up to now, none of satisfied experimental method has been reported for studying mass transport of a whole process in liquid media yet. This paper described the experimental approach to explore mass transport in electrochemical system by transmission Vop-spectroellipsometry briefly.

Go to article

Synthesis And Electrochemical Behavior Of Layered-Structure Limn_(1-X)Cr_Xo_2, Jie Xiao, Hui Zhan, Yun-Hong Zhou Aug 2004

Synthesis And Electrochemical Behavior Of Layered-Structure Limn_(1-X)Cr_Xo_2, Jie Xiao, Hui Zhan, Yun-Hong Zhou

Journal of Electrochemistry

The Layered-structure LiMn_(1-x)Cr_xO_(2 )(x=0,0.15) solid solution has been prepared by the rheological phase method. From the XRD results, undoped LiMnO_(2) crystallized almost entirely in the orthorhombic phase while the structure of LiMn_(0.85)Cr_(0.15)O_(2) belongs to monoclinic phase. TEM investigation shows that the final powder product consists of ultrafine spherical particles which are distributed homogeneously, with the average diameter ranging from 60 to 300nm. The initial discharge capacity of LiMn_(0.85)Cr_(0.15)O_(2) is much higher than that of undoped LiMnO_(2). After 40 cycles, the capacity retention for m-LiMn_(0.85)Cr_(0.15)O_(2 )is 94% at the current rate of 50mA/g under room temperature. The results of electrochemistry tests …

Go to article

Lithium Insertion Into Tio_2(B) Nanobelts Synthesized By The "Soft Chemical" Method, Cha-Geng Nie, Zheng-Liang Gong, Lan Sun, Juan Zuo, Yue-Kun Lai, Chang-Jian Lin Aug 2004

Lithium Insertion Into Tio_2(B) Nanobelts Synthesized By The "Soft Chemical" Method, Cha-Geng Nie, Zheng-Liang Gong, Lan Sun, Juan Zuo, Yue-Kun Lai, Chang-Jian Lin

Journal of Electrochemistry

TiO_(2)(B) Nanobelts were synthesized by using the "Soft chemical"method. The products were characterized by means of transmission electron microscope(TEM), X-ray diffraction(XRD), Raman spectrum and energy dispersive spectrum(EDS). Galvanostatic charging and discharging tests showed that lithium-ion intercalation/deintercalation occurred reversibly in the TiO_(2)(B) nanobelts electrode, and a high capacity (265 mAh·g~(-1)) can be obtained. The results suggested that TiO_(2)(B) Nanobelts might be a promising negative electrode material of second Lithium battery.

Go to article

The Effect Of Ferrous Sulphate On The Electroless Depositionof Co-Fe-P Alloys, Sen-Lin Wang, Qing-Hua Li Aug 2004

The Effect Of Ferrous Sulphate On The Electroless Depositionof Co-Fe-P Alloys, Sen-Lin Wang, Qing-Hua Li

Journal of Electrochemistry

Electroless deposition of Co-P alloy and Co-Fe-P alloy from an alkaline bath, containing sodium hypophosphite as a reducer, boric acid as a buffer agent and sodium citrate as a complexing agent, was investigated respectively. The effects of process parameters, such as pH of solution and metallic salt mole ratio of CoSO_(4)/FeSO_(4), on the plating rate were examined. It was found that the presence of ferrous sulfate in the bath has an inhibitory effect on the alloy deposition. As a consequence, the plating rate of Co-Fe-P is lower than that of Co-P. The electrochemical polarization measurements have been carried out to …

Go to article

Study On An Intermediate Temperature Planar Solid Oxide Fuel Cell, Shao-Rong Wang, Wen-Xia Chen, Ting-Lian Wen, Jia-Di Cao, Zhi-Yi Lv, Da-Qian Wang Aug 2004

Study On An Intermediate Temperature Planar Solid Oxide Fuel Cell, Shao-Rong Wang, Wen-Xia Chen, Ting-Lian Wen, Jia-Di Cao, Zhi-Yi Lv, Da-Qian Wang

Journal of Electrochemistry

Tape cast method was applied to prepare green sheets of Ni/YSZ anode supported YSZ thin film. After isostatic pressure treatment and cosintering, the YSZ film on the Ni/YSZ anode was gas-tight dense, and 15~30 μm thick. The area of the composite film was over 100 cm~(2). A Ce_(0.8)Sm_(0.2)O_(1.9 )(CSO) interlayer was sintered on to the YSZ electrolyte film to protect La_(0.6)Sr_(0.4)CoO_(3 )(LSCO) cathode from reaction with YSZ at high temperatures. The LSCO cathode layer was screen printed onto the CSO interlayer and sintered at 1 200 ℃ for 3h to form a single cell. The obtained single cell was operated …

Go to article

Fabrication Of Solid Oxide Fuel Cells And Analysis Of Their Structure And Performance, Nai-Tao Yang Aug 2004

Fabrication Of Solid Oxide Fuel Cells And Analysis Of Their Structure And Performance, Nai-Tao Yang

Journal of Electrochemistry

An intermediate temperature solid oxide fuel cell (IT-SOFC) was fabricated by co-copressing-sintering methods, and the electrolyte of Ce_(0.8)Gd_(0.2)O_(1.9) (CGO) and cathode materials of La_(0.6)Sr_(0.4)Co_(0.2)Fe_(0.8)O_(3-α) (LSCF) were prepared by sol-gel method. The effect of preparation methods on the microstructure of the prepared fuel cells was analyzed by SEM . It shows that the cells prepared by the co-pressing/co-sintering method possess a dense electrolyte layer and a compact interface between electrolyte and anode but a curved configuration, while those prepared by the colloidal technique have a flat configuration but the electrolyte layer is not dense enough. The maximum output power density of …

Go to article

Electrochemical Reduction Of Nitrobenzene On The Wc Electrode In Acidic Solution, Chun-An Ma Aug 2004

Electrochemical Reduction Of Nitrobenzene On The Wc Electrode In Acidic Solution, Chun-An Ma

Journal of Electrochemistry

The tungsten carbide (WC) electrode was constructed by using polyterafluoroethylene as binder. The electrochemical behavior of nitrobenzene on the WC electrode in acidic solution was investigated by cyclic voltammetry, linear scan method and chronoamperometry. Experimental results showed that WC electrode had good activity for the electrochemical reduction of nitrobenzene, and the electrode process was controlled by diffusion and electrochemical stepssimultaneously. The apparent active energy of the electrode process is 23.7kJ mol~(-1), while the active energy of the electrochemicalstep is 10.91kJ mol~(-1).

Go to article

Synthesis Of (S)-3-Phenylpropane-2-Tert-Butoxycarbonylamino- 1-Thiol And Its Electrochemical Behavior Self-Assembled On Gold, Sun Ru Aug 2004

Synthesis Of (S)-3-Phenylpropane-2-Tert-Butoxycarbonylamino- 1-Thiol And Its Electrochemical Behavior Self-Assembled On Gold, Sun Ru

Journal of Electrochemistry

The synthesis of (S)-3-Phenylpropane-2-tert-butoxycarbonylamino- 1-thiol(N-Boc-APT) from L-phenylalanine was reported. L-Phenylalanine was reduced to the corresponding amino alcohol, protection of the amino group using tert-butyl pyrocarbonate gave (S)-2-tert-butoxycarbonylamino-3-phenylpropane-1-ol, which was then O-mesylated and treated with potassium thioacetate in DMF to give 3-phenylpropane-2-tert- butoxycarbonylamino-1-etylmercapto. After the acetyl group was removed with ammonia in alcohol, the desired target molecular was obtained. The structure of intermediate and target molecular was conformed by IR and ~(1)HNMR. We made N-Boc-APT self-assemble-modificated gold electrode and investigated its electrochemical behavior. The CV results of methylene blue on nano-Au/N-Boc-APT SAM/Au electrode showed that nano-Au could speed this electron transfer …

Go to article

The Electrochemical Behavior And Determination Of Gsh At The Powder Microelectrode, Jian Chen, Zhong-Yu He, Chuansin Cha, Huan Liu Aug 2004

The Electrochemical Behavior And Determination Of Gsh At The Powder Microelectrode, Jian Chen, Zhong-Yu He, Chuansin Cha, Huan Liu

Journal of Electrochemistry

In this paper, the electrochemical behavior of GSH at the surface of platinum(Pt) electrode, glass carbon(GC) electrode and acetylene black packed powder microelectrode (AB-PME) was studied. It was found that the electrochemical oxidations of GSH at both Pt and GC electrode were highly irreversible. No current peak or current plateau could be observed from the CV curves. The direct electro-oxidation of GSH at carbon surface was achieved by using the PME technique.In this case, the apparent reversibility of GSH oxidation was enhanced significatly .The overpotential of GSH oxidation was reduced to 0.5 V at the surface of AB-PME compared with …

Go to article

Nucleation And Crystal Growth Of Pt Electrodeposition On Poly Crystal Au Microdisc Electrode, Zhi-Yong Tao, Pei-Fang Liu Aug 2004

Nucleation And Crystal Growth Of Pt Electrodeposition On Poly Crystal Au Microdisc Electrode, Zhi-Yong Tao, Pei-Fang Liu

Journal of Electrochemistry

Based on the Fleischmann's model of nucleation and crystal growth for electrodeposition combined with the Barradas-Bosco's adsorption-nucleation model for electrochemical phase formation, the chronoamperometry was well fitted for Pt deposition on polycrystalline Au micro disc electrodes (30 μm in diameter) in different H_(2)PtCl_(6) concentrations at different over-potentials. The initial stage of Pt deposition in dilute H_(2)PtCl_(6) could be interpreted by the model of H_(2)PtCl_(6 ) adsorption combined with instantaneous nucleation and two-dimensional cylindrical growth. The rate constant of the two-dimensional growth increased linearly with overpotential. Then the deposit grew layer by layer and the rate constant increased non-linearly with overpotential. …

Go to article

Preparation And Electrochemical Performance Of New Composite Seperators For Lithium-Ion Batteries, Hu Cheng, Hong-Yan Du, Yong Yang Aug 2004

Preparation And Electrochemical Performance Of New Composite Seperators For Lithium-Ion Batteries, Hu Cheng, Hong-Yan Du, Yong Yang

Journal of Electrochemistry

New composite seperators for lithium ion batteries were prepared by coating PEO mixed with nanosize SiO_(2)onto microporous polypropylene(PP) seperators. Highly conductive electrolytes were prepared by soaking them in an electrolyte solution. With these composite separators, the lithium ion cell consisting of Li anode and LiNi_(0.8)Co_(0.2)O_(2)cathode were assembled. The high initial discharge capacity and good capacity retention were obtained through the cell.

Go to article

Effects Of Barium On The Performance Of Secondary Alkaline Zinc Electrode, Yi Zheng, Jian-Ming Wang Aug 2004

Effects Of Barium On The Performance Of Secondary Alkaline Zinc Electrode, Yi Zheng, Jian-Ming Wang

Journal of Electrochemistry

The active material of secondary alkaline zinc electrode with barium additives was prepared by a chemical reaction method and characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The electrochemical performance of various pasted Zn electrodes was investigated by cyclic voltammetry, charge/discharge method and electrochemical impedance spectra (EIS) technology. The addition of barium can synthesize a compound barium zincate with the molecular structure of BaZn(OH)_(4)· xH_(2)O and improve the discharge performance. The EIS of the various Zn electrodes showed two time constants besides diffusion impedance, including a state variable representing the covering degree of discharge products on the electrode …

Go to article

Solid State Synthesis And Electrocatalysis Of Pt/Moo_3 For The Oxidation Of Methanol, Wang Qing Aug 2004

Solid State Synthesis And Electrocatalysis Of Pt/Moo_3 For The Oxidation Of Methanol, Wang Qing

Journal of Electrochemistry

The electrocatalyst, Pt/MoO_(3) synthesized by solid state reaction, was used for the oxidation of methanol in direct methanol fuel cells. The X-Ray diffraction and cyclic voltammetry were employed to investigate the performance of the material. It was shown that the typical diffraction peaks for Pt appeared in XRD. And a good electrocatalysis for methanol oxidation was observed. The peak potential of the methanol oxidation appeared at ca. 0.63V(vs.SCE) and the peak current density for the oxidation was 78.1 mA cm~(-2) .

Go to article

Preliminary Study Of Speek Membranes For Direct Methanol Fuel Cells Application, Su-Zhen Ren Aug 2004

Preliminary Study Of Speek Membranes For Direct Methanol Fuel Cells Application, Su-Zhen Ren

Journal of Electrochemistry

This paper describes the methanol permeability characterization of SPEEK membranes and their feasibility for DMFC application. The SPEEK membranes showed a significant lower methanol permeation than Nafion~115 determined from voltammetric methods. An increase in open circuit voltage was found in the performance of SPEEK membranes in DMFC. The power density of the cell using SPEEK membrane was considerably poorer than that of Nafion~115. If modified properly, the SPEEK membranes can be chosen for DMFC application based on this study.

Go to article

Preparation Of Photo-Electrochemical Anticorrosion Tio_2 Films By Anodization Method, Peng-Fei Wu, Mou-Cheng Li, Jia-Nian Shen, Mei-Qun Xiao, Dong Liu Aug 2004

Preparation Of Photo-Electrochemical Anticorrosion Tio_2 Films By Anodization Method, Peng-Fei Wu, Mou-Cheng Li, Jia-Nian Shen, Mei-Qun Xiao, Dong Liu

Journal of Electrochemistry

Titanium oxide films have photo-electrochemical anticorrosion effect. We investigated the TiO_(2) films prepared by anodization method to protect for 45~(#) carbon steel in man-made seawater(3%NaCl). Various parameters, including voltages, electrolytes nature and concentration of electrolyte were examined. The polarization curves and of TiO_(2) and coupling photo-current curve between TiO_(2) film and 45~(#) carbon steel were measured.

Go to article

Electrochemical Lithium Insertion Of Nanosized Tio_2, Ying Lan, Jian-Wen Liu, Xue-Ping Gao, Xing-Di Zhou, Jin-Qiu Qu, Feng Wu, De-Ying Song May 2004

Electrochemical Lithium Insertion Of Nanosized Tio_2, Ying Lan, Jian-Wen Liu, Xue-Ping Gao, Xing-Di Zhou, Jin-Qiu Qu, Feng Wu, De-Ying Song

Journal of Electrochemistry

The protonic titanate nanotubes with the diameter of 10～15 nm were synthesized via hydrothermal method in NaOH solution and the calcined nanotubes at 500 ℃ were transferred to anatase nanorods with the diameter of 12～20 nm due to dehydration.The electrochemical behavior of the anatase nanorods as lithium insertion materials was examined. The results showed that the nanorod electrode had the high initial discharge capacity of 232 mAh/g and second reversible capacity of 198 mAh/g. The capacity of nanorod electrode maintained 152mAh/g after 20 cycles.

Go to article

The Matching Study Of Electrodes In C/Ni(Oh)_2 Hybrid Capacitor, Yue-Feng Su May 2004

The Matching Study Of Electrodes In C/Ni(Oh)_2 Hybrid Capacitor, Yue-Feng Su

Journal of Electrochemistry

The energy storage mechanisms of electrochemical double-layer capacitor (EDLC) and C/Ni(OH)_2 hybrid capacitor had been studied. The results proved that,the difference between the capacity of EDLC and C/Ni(OH)_2 hybrid capacitor was detemined by the effectiveness usage of the activated carbon negative electrode, which is a criterion to estimate or design the theoretic capacity of the C/Ni(OH)_2 hybrid capacitor.The electrochemical availability of activated matter in Ni(OH)_2 electrode was introduced,and the quantity of the activated matter in Ni(OH)_2 electrode should be compatible with the capacity of carbon electrode .When the capacities of Ni(OH)_2 electrode and activated carbon electrode were matched well,the capacity …

Go to article

Direct Electron Transfer Of Redox Proteins And Enzymes Promoted By Carbon Nanotube, Chen-Xin Cai May 2004

Direct Electron Transfer Of Redox Proteins And Enzymes Promoted By Carbon Nanotube, Chen-Xin Cai

Journal of Electrochemistry

The redox proteins (enzymes), such as hemoglobin (Hb), horseradish peroxidase (HRP) and glucose oxidase (GOx) were immobilized on the surface of the carbon nanotube modified with glassy carbon (CNT/GC) electrode, respectively. The experimental results showed that the redox proteins (enzymes) underwent effective and stable direct electron transfer reaction at the surface of CNT/GC electrode with a pair of nearly symmetrical redox peaks in phosphate buffer solution. The formal redox potential, E~(0'), is almost independent on the scan rates, the average value of E~(0') for Hb, HRP and GOx is -0.343±0.001, -0.319±0.002 and -0.456±0.001 V (vs.SCE,pH 6.9), respectively. The dependence of …

Go to article

Stability And Electrochemical Performance Of Nio Cathode Modified By Zno Additive For Mcfc In Molten Carbonates, Huang Bo May 2004

Stability And Electrochemical Performance Of Nio Cathode Modified By Zno Additive For Mcfc In Molten Carbonates, Huang Bo

Journal of Electrochemistry

The ZnO/Ni composite cathode was fabricated by tape-casting method, which microstructures and phases were studied. The electrochemical behaviors of ZnO impregnated NiO cathodes were also evaluated in molten 62 mol%Li_2CO_3+(38 mol%) K_2CO_3eutectic at 650 ℃ by electrochemical impedance spectroscopy (EIS) as a function of ZnO content and immersion time. The ZnO impregnated nickel cathodes showed the similar porosity, pore size and morphology to the reference nickel cathode. The stability tests of ZnO impregnated NiO cathodes showed that the ZnO additive could dramatically reduce the solubility of NiO in a eutectic carbonate mixture under the standard cathode gas condition. The cathode …

Go to article

Next Last