Open Access. Powered by Scholars. Published by Universities.®

Engineering Science and Materials Commons™

Open Access. Powered by Scholars. Published by Universities.®

Series

Technological University Dublin

Doctoral

Articles 1 - 6 of 6

Full-Text Articles in Engineering Science and Materials

Towards A Sociotechnical Reconfiguration Of Engineering And An Education For Ethics : A Critical Realist Investigation Into The Patterns Of Education And Accreditation Of Ethics In Engineering Programmes In Ireland, Diana Adela Martin Jul 2020

Towards A Sociotechnical Reconfiguration Of Engineering And An Education For Ethics : A Critical Realist Investigation Into The Patterns Of Education And Accreditation Of Ethics In Engineering Programmes In Ireland, Diana Adela Martin

Doctoral

The focus of this thesis is on the provision and evaluation of ethics in engineeringprogrammes in Ireland, by placing this examinationin the wider cultural context of engineering education.The study benefitted from the support of the national accrediting body Engineers Ireland, and included 23 engineering programmes from 2 institutes of technology and 4 universities in Ireland which underwent accreditation between 2017-2019.By using a Critical Realistframe, the study undertakes a multi-layeredinvestigation of the engineering education system that takes into consideration theindividual level of single agents such as instructors and evaluators, the institutional level comprised of engineering programmes, as well as the policy …

Go to article

Fatigue Properties Of Magnetorheological Elastomers And The Design Of Interfacial Layers To Improve Fatigue Life., Yanfen Zhou Jan 2016

Fatigue Properties Of Magnetorheological Elastomers And The Design Of Interfacial Layers To Improve Fatigue Life., Yanfen Zhou

Doctoral

The primary aim of this PhD programme was to understand the fatigue behaviour of magnetorheological elastomers (MREs) and provide a reliable fatigue life predictor for this class of materials. To realise this aim required the study of the dynamic behaviour of MREs using the equi-biaxial bubble inflation test method. Isotropic and anisotropic MREs were fabricated from silicone rubber (SR) filled with soft carbonyl iron (CI) particles. The equi-biaxial fatigue behaviour of these samples was determined using a bubble inflation method. Wöhler (S-N) curves for both isotropic and anisotropic MREs were produced by subjecting the compounds to cycling over a range …

Go to article

Numerical Prediction Of The Haemodynamic Impact Of Coronary Stent Implantation, Jonathan Murphy Apr 2011

Numerical Prediction Of The Haemodynamic Impact Of Coronary Stent Implantation, Jonathan Murphy

Doctoral

Arterial restenosis limits the effectiveness of coronary stenting. Restenosis is caused by excessive tissue growth which is stimulated by arterial injury and alterations to the arterial WSS. The altered WSS results from stent-induced disturbances to the natural haelnodynamics of the artery. Recent numerical studies have predcted only minor digerences in altered WSS between different stent designs using a commonly employed threshold assessment technique. While it is possible that there are only minor differences, it is more likely that the assessment technique is incapable of fully elucidating the altered WSS created by stent implantation. This thesis proposes a methodology that involves …

Go to article

Phase Change Materials For Thermal Regulation Of Building Integrated Photovoltaics, Ahmad Hassan Jan 2010

Phase Change Materials For Thermal Regulation Of Building Integrated Photovoltaics, Ahmad Hassan

Doctoral

In outdoor deployed photovoltaics (PV), standard test conditions (STC) of 25 °C PV temperature, 1000 Wm-2 solar radiation intensity and 1.5 air-mass rarely prevail. PV temperature can rise 40-100 °C above STC inducing a power drop in crystalline silicon PV with a coefficient of -0.4 to -0.65 %/K above STC. Increased operating temperature also results in accelerated PV degradation due to cell delamination allowing moisture ingress. vConventional building integrated photovoltaics (BIPV) cooling techniques using passive
or active heat removal by air or water flow are limited by (i) very low heat transfer or (ii) large capital as well as maintenance …

Go to article

Investigation Of Uv-Led Initiated Photopolymerisation Of Bio-Compatible Hema, Sharon Mcdermott Sep 2008

Investigation Of Uv-Led Initiated Photopolymerisation Of Bio-Compatible Hema, Sharon Mcdermott

Doctoral

Ultraviolet (UV) fluorescent lamps are widely used in photopolymerisation processes. However, there a number of disadvantages to these lamps, namely, their intensity varies over time and has to be constantly monitored. This thesis is concerned with the possibility of replacing these lamps with UV Light Emitting Diodes (UV-LEDs). A number of emission characteristics of both the fluorescent lamp and the UV-LEDs were measured and compared to ensure that the optical properties of the UV-LEDs were equivalent to those of the lamps. From this study it was shown that the UV-LEDs have a quicker warm up time and exhibit a more …

Go to article

Structure Property Relationships In Electron Donating Systems For Potential Photovoltaic Applications., Jonathan Moghal Jan 2008

Structure Property Relationships In Electron Donating Systems For Potential Photovoltaic Applications., Jonathan Moghal

Doctoral

Conjugated polymers are considered to be one-dimensional semiconductors. In conjugated polymers single and double bonds alternatively bond the carbon atoms along the polymer chain. The loosely bound electrons determine the electronic properties of conjugated polymers. In order to utilise the properties of conjugated polymers in terms of a photovoltaic (PV) device application an acceptor material must be added. The acceptor material used in this study is used in buckminsterfullerence (C60). C60 was selected for this purpose due to its size and the fact that it can accept up to six additional electrons. Ultrafast charge transfers from a conducting polymer onto …

Go to article