Open Access. Powered by Scholars. Published by Universities.®
Engineering Science and Materials Commons™
Open Access. Powered by Scholars. Published by Universities.®
- Discipline
- Keyword
-
- Fluids (2)
- 3D scanning (1)
- AISI S901-13 Rotational-Lateral Test Method (1)
- Anchorage forces (1)
- Construction engineering (1)
-
- Construction management (1)
- Effective standoff (1)
- Error aggregation (1)
- Flexural strength (1)
- John Lumley (1930-2015) (1)
- Lateral restraint (1)
- Mechanics (1)
- Panel-clip connections (1)
- Parametric comparison of standing seam systems (1)
- Plane of lateral resistance (1)
- Plasma (1)
- Plasmas (1)
- Postgraduate education (1)
- Printing (1)
- Purlin supported standing seam roof systems (1)
- Purlins (1)
- RFID (1)
- Rotational stiffness (1)
- Senior project (1)
- Sheathing (1)
- Standing seam roof systems (1)
- Stress (1)
- Test results (1)
- Thermodynamics (1)
- Torsional restraint (1)
Articles 1 - 5 of 5
Full-Text Articles in Engineering Science and Materials
Comment On "Roles Of Bulk Viscosity On Rayleigh-Taylor Instability: Non-Equilibrium Thermodynamics Due To Spatio-Temporal Pressure Fronts" Phys. Fluids 28, 094102 (2016), Robert L. Ash
Mechanical & Aerospace Engineering Faculty Publications
No abstract provided.
Preface To Special Topic: A Tribute To John Lumley, Kiran Bhaganagar, Thomas B. Gatski, William K. George
Preface To Special Topic: A Tribute To John Lumley, Kiran Bhaganagar, Thomas B. Gatski, William K. George
CCPO Publications
This Special Topic Section is dedicated to the life and memory of John Leask Lumley(1930-2015), professor and scientist extraordinaire.
Impact Of Clip Connection And Insulation Thickness On Bracing Of Purlins In Standing Seam Roof Systems, Michael W. Seek, Daniel Mclaughlin
Impact Of Clip Connection And Insulation Thickness On Bracing Of Purlins In Standing Seam Roof Systems, Michael W. Seek, Daniel Mclaughlin
Engineering Technology Faculty Publications
The flexural strength of purlins in standing seam roof systems is highly dependent upon the extent to which the sheathing provides lateral and torsional restraint. Typical models to predict the restraint provided by the sheathing assume that the plane of lateral resistance occurs at the top flange of the purlin. In reality, depending on the configuration of the clip and the amount of insulation located between the purlin and the clip, the plane of lateral resistance and corresponding center of rotation shifts above the top flange. This distance, referred to as the effective standoff, is important to evaluate the effectiveness …
Error Aggregation In The Reengineering Process From 3d Scanning To Printing, Jennifer G. Michaeli, Matthew C. Degroff, Roman C. Roxas
Error Aggregation In The Reengineering Process From 3d Scanning To Printing, Jennifer G. Michaeli, Matthew C. Degroff, Roman C. Roxas
Engineering Technology Faculty Publications
This work aims to study the aggregation of dimensional errors in the reengineering processes using 3D scanning and printing without initial design drawings. A 57-tooth spur gear is used as an example to facilitate the discussion. Two approaches are investigated. The first one builds the gear model based upon measurement taken from a caliper, and the second approach uses a 3D scanner to collect geometry data. Dimensional errors in each stage of these two approaches are investigated. Particular attention is paid to the geometry data flow in the reengineering process from data acquisition and editing to model construction. Recommendations are …
Evaluating The Readability Of Radio Frequency Identification For Construction Materials, Younghan Jung, Michael M. Jeong
Evaluating The Readability Of Radio Frequency Identification For Construction Materials, Younghan Jung, Michael M. Jeong
Engineering Technology Faculty Publications
Radio Frequency Identification (RFID), which was originally introduced to improve material handling and speed production as part of supply chain management, has become a globally accepted technology that is now applied on many construction sites to facilitate real-time information visibility and traceability. This paper describes a senior undergraduate project for a Construction Management (CM) program that was specifically designed to give the students a greater insight into technical research in the CM area. The students were asked to determine whether it would be possible to utilize an RFID system capable of tracking tagged equipment, personnel and materials across an entire …