Engineering Science and Materials Commons^™

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Sorption Of Ions Of Some Metals On Synthesized Weakly Basic Ion Exchangers, Dilmurod Azimov, S. Turabjanov, Farrukh Igitov, Rano Nazirova, Tulkin Tursunov

CHEMISTRY AND CHEMICAL ENGINEERING

The purpose of the study is to test a weakly basic anion exchanger of the polycondensation type in the processes of sorption of ions of copper, nickel, cobalt, zinc, cadmium. Among the indicated metal ions, the maximum sorption was established for copper ions.

To study the process of sorption of copper ions by the tested anion exchanger, the method of potentiometric titration was used. It was found that copper ions are sorbed by the anion exchanger in the form of a complex in the range of pH = 3,4-4,2. The formation of the copper ions complexes decreases with an increase …

Investigation On Laser Induced Deposition Of Cu-Based Materials At [Bmim]Bf4/Pt Electrode Interface, Min-Min Xu, Jin-Hua Mei, Jian-Lin Yao, Ren-Ao Gu

Journal of Electrochemistry

By controlling the negative potential, Cu-based materials were deposited at the [BMIm]BF₄/Pt electrode interface under the laser irradiation. The effects of laser power and irradiation time on the yield of deposition products were studied by using different laser powers and different irradiation time. The product yield could be directly determined by the size of deposition point through the observation from the optical microscope. Further mechanism study combined with the formula deduced that the thermal effect of the laser could make the electrode surface temperature rise 110 degrees, which can promote the occurrence of electrodeposition. By SEM characterization, the …

Doped Tio2 Nanowires For Applications In Dye Sensitized Solar Cells And Sacrifical Hydrogen Production, Qasem Alsharari

Electronic Thesis and Dissertation Repository

This thesis explores the synthesis of metal oxide 1-D nanowires using a sol-gel method in supercritical carbon dioxide (sc-CO₂), as an environmental friendly enabling solvent. Porous nanowires were synthesized and their performance was tested in dye sensitized solar cell and sacrifical hydrogen production. Titanium isopropoxide (TIP) was used as a precursor for titania synthesis while copper, bismuth and indium were examined as dopants, respectively. The sol-gel reactions were catalyzed by acetic acid in CO₂ at a temperature of 60 °C and pressure of 5000 psi. It was observed that acetic acid/monomer ratio > 4 produced nanowires while a …

Electrodeposition Of Copper From A Choline Chloride Based Ionic Liquid, Rostom Ali M., Ziaur Rahman Md., Sankarsaha S.

Journal of Electrochemistry

The electrodeposition of copper from a solution containing copper chloride in either an ethylene glycol (EG)-choline chloride based or a urea-choline chloride based ionic liquid has been carried out onto a steel cathode by constant current and constant potential methods at room temperature. The influences of various experimental conditions on electrodeposition and the morphology of the deposited layers have been investigated by scanning electron microscopy (SEM) and X-ray diffraction (XRD). It is shown that very smooth, shiny and dense with good adherence and bright metallic coloured copper coatings can be obtained from both EG and urea based ionic liquids at …

The Analysis Of The Tribological Properties Of Multiple Strengthened Nanocomposite Of The Cu-Al2o3 System, Zeljko J. Kamberovic

Zeljko J Kamberovic

This paper presents the results of examined tribological properties of the multiple strengthened nanocomposite Cu-Al2O3 system. Cu-Al2O3 composite powder was obtained by combination of the thermo-chemical procedure and mechanical alloying, which is a completely new approach to synthesis of these materials. The synthesized powders were cold pressed with 940MPa and sintered in hydrogen atmosphere in temperature range of 725-925o C during 15-120 minutes. The samples were thermo- mechanically treated in two stages after sintering: cold rolling with the final reduction degree of 30% and annealing at 800o C for 1h in hydrogen atmosphere. Characterization of the sintered, rolled and annealed …

Effect Of Moisture Absorption On The Sinter Quality Of Central Solenoid (Cs) Coil Pack, Zeshaan Sher Mohammed

Masters Theses

Fusion energy has been said to be the solution to all the world’s energy problems. The International Thermonuclear Experimental Reactor (ITER) is the flagship project to demonstrate the feasibility of fusion energy. The Central Solenoid (CS), an important component of the reactor, is needed to induce plasma current, initiate, ramp-up, ramp-down, and sustain plasma in a very controlled manner. In order to achieve this, the CS coil packs must be manufactured under controlled conditions. The CS conductor is an advanced cable-in-conduit Nb3Sn superconductor. The CS cable will be made in long continuous sections but with thousands of meter of cable …

Hydrometallurgical Process For Extraction Of Metals From Electronic Waste-Part I: Material Characterization And Process Option Selection, Zeljko J. Kamberovic

Zeljko J Kamberovic

Used electronic equipment became one of the fastest growing waste streams in the world. In the past two decades recycling of printed circuit boards (PCBs) has been based on pyrometallurgy, higly polluting recycling technology whic causes a variety of environmental problems. The most of the contemporary research activities on recovery of base and precious metals from waste PCBs are focused on hydrometallurgical techniques as more exact, predictable and easily controlled. In this paper mechanically pretrated PCBs are leached with nitric acid. Pouring density, percentage of magnetic fraction, particle size distribution, metal content and leachability are determined using optical microscopy, atomic …

Electronic And Structural Properties Of Molybdenum Thin Films As Determined By Real Time Spectroscopic Ellipsometry, J. D. Walker, H. Khatri, V. Ranjan, Jian Li, R. W. Collins, S. Marsillac

Electrical & Computer Engineering Faculty Publications

Walker, J.D., Khatri, H., Ranjan, V., Li, J., Collins, R.W., & Marsillac, S. (2009). Electronic and structural properties of molybdenum thin films as determined by real-time spectroscopic ellipsometry. Applied Physics Letters, 94(14). doi: 10.1063/1.3117222

Determination Of Al2o3 Particle Size In Cu-Al2o3 Nanocomposite Materials Using Uv Spectrophotometry, Zeljko J. Kamberovic

Zeljko J Kamberovic

In order to achieve improved mechanical properties of dispersion strengthened nanocomposite, without influencing electrical and thermal conductivity it is necessary for dispersoide to be nano sized and uniformly distributed in base metal matrix. In this paper are presented the results concerning possibility of using UV spectrophotometry for determination of alumina particle size in Cu-Al2O3 system. Presented results show that this method is unefficient as method for determination of dispersoide particle size, due to the coalescence of particles false results are obtained, i.e. particle size significantly higher then one determined by image analysis.

Sintering Of Cu–Al2o3 Nano-Composite Powders Produced By A Thermochemical Route, Zeljko J. Kamberovic

Zeljko J Kamberovic

This paper presents the synthesis of nano-composite Cu–Al2O3 powder by a thermochemical method and sintering, with a comparative analysis of the mechanical and electrical properties of the obtained solid samples. Nano-crystalline Cu–Al2O3 powders were produced by a thermochemical method through the following stages: spray-drying, oxidation of the precursor powder, reduction by hydrogen and homogenization. Characterization of powders included analytical electron microscopy (AEM) coupled with energy dispersive spectroscopy (EDS), differenttial thermal and thermogravimetric (DTA–TGA) analysis and X-ray diffraction (XRD) analysis. The size of the produced powders was 20–50 nm, with a noticeable presence of agglomerates. The composite powders were characterized by …

Synthesis And Sintering Of Cu-Al2o3 Nanocomposite Powders Produced By A Thermochemical Route, Zeljko J. Kamberovic

Zeljko J Kamberovic

By hydrometallurgy and powder metallurgy along with prognosis of physical- chemical properties, a synthesis of new improved materials can be successfully performed with in advance pre-set properties which is conditioned by a quality of starting powders i.e. by improving their structure. In accordance with that, this paper presents synthesis of the nanocomposite Cu-Al2O3 powder by thermochemical method and sintering with a comparative analysis of the mechanical and electrical properties of obtained solid samples. Nanocrystaline Cu-Al2O3 powders were produced by thermochemical method through following stages: spray-drying, oxidation of precursor powder, reduction by hydrogen and homogenisation. Characterization of powders included differential-thermal and …

Effects Of Sulfide Ions On The Inhibiting Efficiency Of Eda As A Copper Corrosion Inhibitor In Dilute Hcl Solution, Wen-Juan Qu, Rong-Gui Du

Journal of Electrochemistry

The anticorrosion action of EDA on copper in dilute HCl solution and the effect of sulfide ions on the inhibiting efficiency were studied by the Tafel plot method.The corrosion potential of Cu shifted to more positive value and the corrosion current density decreased after the addition of Na_(2)S to the solution.The results indicated that sulphide ions could increase the inhibiting efficiency of EDA because of the synergistic inhibition effect between EDA and Na_2S,resulting from the adsorption of HS~(-)on the surface of Cu,facilitated the adsorption of EDA to form a highly protective adsorbed layer which prevented Cu from corrosion.

The Synthesis Of Ultrafine And Nanocomposite Powders Based On Copper, Silver And Alumina, Zeljko J. Kamberovic

Zeljko J Kamberovic

Contemporary materials with predetermined properties can be successfully synthesized by utilising the principles of hydrometallurgy and powder metallurgy. The results of developing a new procedure for the synthesis of ultrafine and nanocomposite powders based on copper, silver and alumina are presented in this paper. A two-component nanocomposite powder, Cu-Al2O3, was synthesized by a thermochemical procedure, by deposition from an aqueous solution of soluble metal salts, Cu(NO3)2 and Al(NO3)3. A three-component Cu-Ag-Al2O3 powder was produced by mechanically alloying nanocomposite Cu-Al2O3 powder and Cu-Ag powder, synthesized by the thermochemical procedure. The produced powders were characterized by determining the particle specific area, pouring …

Copper Electrodeposition Under The Perturbation Of Hard Particles, Zeng-Wei Zhu, Di Zhu

Journal of Electrochemistry

Copper electrodepositon was carried out on the rotating cathode,with hard particles(such as ceramic beads) filling between the electrodes.The rotation of cathode led hard particles to polish and impact the surface of deposit during electrodeposition.Copper deposits with a mass of cuspidal nodules were produced in acid sulfate solutions while brittle deposits without nodules were produced in alkaline sulfate solutions.It was also found that brightening and smoothing deposit could be obtained from the alkaline solution,and the deposit was approximatively disordered orientation with granular morphology of about 100~300 nm.The results show that the polishing and impact of hard particles can effectively disturb the …

Electrodeposition Of Copper Into Trenches Under Rotating Hydrodynamic Condition, Jian-Jun Sun

Journal of Electrochemistry

Silicon chips patterned with treneches were fixed onto a rotating electrode. Copper was electrodeposited into the trenches under rotating hydrodynamic conditions The sizes of the trenches are 1 m in height and 0.35 m, 0.50 m and 0.70 m in width, respectively. The effects of rotating of the chip, the current density and the concentration of Cu~(2+ )on the filling of thetrenches were studied. It is found that lower current density and moderate concentration of Cu~(2+)resulted in a void free filling of the trenches.

Effect Of Dissolved Oxygen On The Corrosion Behavior Of Coalesced Copper And Stainless Steel-206 In Acetic Solutions, Rong-Zong Hu, Xiong-Cao Zhao, Yu-Hua Weng, Chang-Jian Lin

Journal of Electrochemistry

Linear sweeping technique and dissolving oxygen sensor were used to study the effect of dissolved oxygen and relating factors on the corrosion behavior of coalesced copper and stainless steel-206 in acetic solutions. It was found: 1. The existing of dissolved oxygen is one of the important factors, which strongly influenced the corrosion behavior of coalesced copper and stainless steel-206 in acetic solution. 2. The existing of dissolved oxygen is benefitial to the preventing stainless steel-206 from corrosion in acetic solutions, but damage to the preventing coalesced copper from corrosion. 3. At the high temperature since the dissolved oxygen was escaping …

Behavior Of Copper In Hydrogen Storage Alloy Microencapsulated By Copper, Dawei Zhang, Huatang Yuan, Huabin Yang, Zuoxiang Zhou, Yunshi Zhang

Journal of Electrochemistry

Negative electrode made from Cu microencapsulated hydrogen storage alloy was studied by using cyclic voltammetry method. The results showed that copper as a coating material was of a certain stability in 5 mol/L KOH solution within the range of charge and discharge voltage. But when expanding the sweep voltage, the CV curve showed a pair of distinct oxidation reduction current peaks of Cu 2O formation at E =-0.3 V and Cu 2O reduction at E =-0.6 V. With charging discharging cycles, copper is liable to be oxidized to Cu 2O and further oxidized into CuO 2- 2. When charged again, …

Electrochemical Study Of The Corrosion Behavior Of Coalesced Copper And Sw-206 Stainless Steel In The Acetic-Acid Solution, Rongzong Hu, Changjian Lin, Jianguang Tan

Journal of Electrochemistry

In order to provide a theoretic and experimental consideration for the material selection and anit-corrosion in the petrochemical industries the corrosion behavior of coalesced copper and sw-206 stainless steel in the acetic acid solution was studied by electrochemical impedance spectroscopy and polarization techniques. The effects of the temperature,acetic acid concentration and solubilized oxygen in the acetic acid solution on the corrosion process of this two metals were analyzed. It was found that these effects obviously accelerate corrosion process for the coalesced copper,but no apparent influnce for the sw-206 stainless steel.In the the acetic acid solution,containing water and oxygen were beneficial …

Cyclic Voltammetric Calorimetry Studying The Deposition Of Copper Of Pt Electrodes, Yongchun Zhu, Robin H J Clark

Journal of Electrochemistry

In the present paper,cyclic voltammetric calorimetry has been used to study thedeposition of copper on platinum electrode from LiClO_4 aqueous solution. Cyclic voltammetricthermogram and cyclic voltammetric differential thermogram show that the deposition of copper on theelectrode is an exothermal process with a strong interaction between copper and platinum layer(-3227.0 kJ /mol).The electrochemical oxidation of the deposited copper is composed of twoprocesses :an endothermal activation process with 747.0 kJ/mol of activation enthalpy,and anexothermal oxidation reaction with-189.9 kJ/mol of the reaction enthalpy, which are accord withthe data from the theoritical estimation and thermodynamic handbook respectively.

Electrochemically Modified Glassy Carbon Electrode And Determination Of Copper By Anodic Stripping Voltammetry, Jinrui Xu, Yie Liu, Xiurun Zhuang

Journal of Electrochemistry

This paper reported the glassy carbon electrode modified by cyclic voltammetrybetween-0. 1and + 1. 5 V(vs. SCE)in an aqueous solution containing catechol,formaldehyde andtalium hydroxide. The modified electrode can be applied to the determination of copper(Ⅱ) in water,and its sensitivity is about 35 times higher than that of unmedified glassy carbon electrede, Thequantitative limit with this modified electrede is 0. 1 ng/ml.