Engineering Science and Materials Commons^™

Fabrication Of Various Curved Relief Structures Through Concave Surface Forming And Soft Replica Molding, Fang-Tzu Chuang

Fang-Tzu Chuang

In this case, our groups presented various optical structures through the presented method, involving concave surface forming and soft replica molding. The method of concave surface forming is mainly for the fabrication of concave surface. The method of soft replica molding is mainly for the fabrication of replica. Concave and convex relief structures, including circular curved relief structures, convex relief structures with platform structures on the top, refractive beam-shaping elements, these structures with dual curvatures and asymmetric structures, can be easily made through the presented method, respectively. All processes of manufacture are in several simple steps without multistep optical lithography …

Comparative Properties Of Polymers Guiding The Development Of An Abdominal Aorta Model, Benjamin Michael Lamie

Masters Theses

Hemodynamics, the study of the forces involved in the circulation of blood, is an area that researchers have approached in various manners for many years. The study of how blood flows through arteries and veins as well as the effect of the composition of the blood has been defined and thoroughly characterized in past studies. Although in-depth studies have been performed on the flow characteristics of blood, most often the observations are made as the fluid flows through tubes composed of some rigid material. It is well known that the arteries and veins have a layered histology that show varying …

A Study Of Material Properties And Relevant Microstructure Parameters That May Influence The V50 Ballistic Limit Velocity Of Composite Ceramics, Adolphus Mcdonald

Masters Theses

The purpose of this research is to evaluate, compare, and correlate the microstructure and mechanical properties of a selected group of ceramic armor samples to the V₅₀ ballistic limit velocity. This study is to identify any relation between the desired material properties and the relevant microstructure parameters that significantly influence the ballistic limit velocity. The ceramic materials, silicon carbide and boron carbide, were produced and provided by five foreign companies. These companies were under contract by the United States Army, Research, Development, and Engineering Command to provide ceramic armor for comparative testing and material evaluation.

Ballistic testing was carried …

Copper Electrodeposition Under The Perturbation Of Hard Particles, Zeng-Wei Zhu, Di Zhu

Journal of Electrochemistry

Copper electrodepositon was carried out on the rotating cathode,with hard particles(such as ceramic beads) filling between the electrodes.The rotation of cathode led hard particles to polish and impact the surface of deposit during electrodeposition.Copper deposits with a mass of cuspidal nodules were produced in acid sulfate solutions while brittle deposits without nodules were produced in alkaline sulfate solutions.It was also found that brightening and smoothing deposit could be obtained from the alkaline solution,and the deposit was approximatively disordered orientation with granular morphology of about 100~300 nm.The results show that the polishing and impact of hard particles can effectively disturb the …

Silicides And Composites Materials As Anodes For Lithium Ion Batteries, Jun-Mei Yan

Journal of Electrochemistry

The anode materials of Mg_(2)Si and MnSi were synthesized by mechanically activated annealing(MAA) techniques in this work and the in electrochemical performances were also studied.A series of composite materials of Mg_(2)Si and CNTs or CMS were prepared by ball-milling method respectively.The reversible capacities of the composites were higher than that of the pure Mg_(2)Si and pure carbon materials.The cyclic performances have been improved greatly by ball-milling of the Mg_(2)Si and carbon materials.Results show that ball-milling method is one kind of method to make alloy materials into practical use.

A Continuous Operation For Electroreduction Of Oxalic Acid To Glyoxylic Acid, Xiao-Hui Hu, Xiang-Fei Yan, Yu-Zhong Su, Jun Li

Journal of Electrochemistry

A simulative-continuous-operation approach was proposed to study the continuous operation for electroreduction of oxalic acid to gloxylic acid using a packed bed reactor and a parallel reactor with cooled cathode in order to solve the low productivity problem in current state by using traditional reactor.The effects of the concentration of oxalic acid and temperature on this process were also studied.Results showed that,after 30min of the reaction(residence time),the mass fraction of the produced glyoxylic acid in the catholic solution could reach 3.76% and 3.66% with respect to a saturated oxalic acid method and a step-temperature decreasing method.From this study,we conclude that …

The Electrocatalystic Investigation Of 3,4-Dihydroxybenzoic Acid On The Modified Multiply Wall Carbon Nanotubes, Ming-Qi Li

Journal of Electrochemistry

The electrochemical behavior of 3,4-Dihydroxybenzoic acid(DHBA)on modified multiply wall carbon nanotubes electrode was investigated by cyclic voltammetry(CV) and square wave voltammetry(SWV).Results show that in 0.1 mol/L HCl solutions the modified carbon nanotube electrode has an obvious electrocatalytic effect on the oxidation and deoxidization of DHBA.The oxidation current of DHBA is linear to it's concentration in the range of 4.0×10~(-6)～1.0×10~(-4) mol/L and 2.0×10~(-4)～8.0×10~(-4)1mol/L with correlation coefficient of 0.9995 and 0.9992.The detection limit is 1.0 ×10~(-6)mol/ L.

The Mechanism Of Ethylenediamine On Electroless Ni-B Alloy Deposition, Sen-Lin Wang

Journal of Electrochemistry

The effects of ethylenediamine stabilizer on the deposition rate and on the stability of the plating bath for electroless deposition of Ni-B alloy were investigated.It was found that the addition of ethylenediamine greatly enhances the stability of the electroless plating bath.The electrochemical polarization including cathodic and anodic polarizations measurements were carried out to examine the effect of ethylenediamine on the deposition process.The results show that ethylenediamine affects both the cathodic and the anodic polarization processes.The oxidation current of the reducer and the reduction current of Ni-B alloy decrease greatly when ethylenediamine was added into the plating bath.The infrared spectroscopy(IR) experiments …

Electrochemical Disinfection Method To Treat Wastewater From Hospitals, Lizhi-Fu Lizhi-Fu

Journal of Electrochemistry

Electrochemical disinfection method was used to treat wastewater from hospitals.The mechanism of electrochemical disinfection was researched by using the different anode materials.The results showed that when the titanium coated with noble metal(Ru、Pt、Ir)oxide was used as an anode and stainless steel as a cathode,the current density was 6 mA/cm~(2),hydraulic retention time was 15 min,air flow rate was 40 L/h,the rate of anode effective area to the inner water volume was 1.0,the amount of total colibacillus was below 500 CFU/L after electrochemical disinfection,All these meet the first order of Effluent Discharge Standard(GB8978-98).

Electrochemical Controllable Preparation Of Hydroxyapatite Coating With Different Morphologies And Preliminary In Vitro Tests, Hai-Yan Shi, Ren Hu, Chang-Jian Lin

Journal of Electrochemistry

The Controllable electrochemical deposition has been developed to prepare the hydroxyapatite(HA) coatings on Ti substrate with different morphologies and structures.Three kinds of typical topography of HA coatings,i.e.standing-up,flower and ordered porous structures have been obtained.The XRD and FTIR results demonstrate high crystallinity of the coating and exclusion of other forms of calcium phosphates.In vitro tests reveal that the biological property is largely dependent on the structure and morphology of the HA coating.It has been found that all pure HA coating show good biocompatibilities,while only the HA coating with ordered porous structures exhibits best bioactivities.

Solid Oxide Fuel Cells-Materials And Prospects, Molenda Janina, Marzec Jacek

Journal of Electrochemistry

The paper summarizes and discusses the basic properties of solid oxide fuel cell(SOFC) components(electrode materials and electrolyte) from the point of view of their essential functional parameters suck as chemicalstability,transport,catalytic and thermomechanical properties under operational conditions in a SOFC.An interrela-tion between the defect structure of these materials related to oxygen nonstoichiometry and their electronic propertiesand catalytic activity was shown.Single-chamber fuel cell concept was also presented.

Effect Of Hco_3~-Concentration On Co_2 Corrosion In Gas And Oil Fields, Guo-An Zhang

Journal of Electrochemistry

The effecs of HCO_3~-concentration on CO_(2) corrosion in gas and oil fields were investigated by carrying out potentiodynamic scans and weight loss tests.Potentiodynamic polarization curves showed that the cathodic current density decreased with cm increase of HCO_3~-concentration when [HCO_3~-] was lower than 0.042(mol/L.)The cathodic reations were promoted by increasing [HCO_3~-] when it reached 0.126 mol/L,(Anodic) behavior was an active process at low er [HCO_3~-] concentration and the anodic current density decreased with the increase of [HCO_3~-] concentration.An evident active-passive behavior exhibited in anodic process at 0.126 mol/L HCO_3~-.Under high pressure and high temperature,the corrosion rate of steel X65 decreased with …

A Study Of Overcharge Characteristic Of Lithium-Ion Cells, Jing Pang, Shi-Gang Lu, Sha Liu

Journal of Electrochemistry

The overcharge characteristics and effect factors of lithium-ion cells containing LiMn_(2)O_(4)cathodes were studied in detail.Overcharge testing of Lithium-ion cells with a systematic variation in the cell balance demonstrated that the overcharge characteristics of Lithium-ion cells was affected by the amount of cathode in the cells,which is independent of the amount of anode material.The rate of charge was found to be an important parameter,as electrolyte complete decomposition at low charge rates caused the end of overcharge testing,while high charge rates accelerated the rate of heat generation in the cells and the cell temperature increased as a result of insufficient heat dissipation.The …

The Deactivation Mechanism Of Metal Oxide Anodes Under Alternative Current Electrolysis Condition, Jun-Tao Wang

Journal of Electrochemistry

The metal oxide anodes coated on titanium used in seawater electrolysis were prepared by thermal decomposition.Their morphologies、compositions and phase structures were determined by scanning electron microscope(SEM)、energy dispersive X-ray detector(EDX) and X-ray diffraction(XRD).The electrochemical properties of the anodes were characterized by accelerated life test,cyclic voltammetry and electrochemical impedance spectroscopy.SEM、EDX and XRD showed that solid solution structures of(Ru,Ir,Ti)O_(2)and(Ir,Ti)O_(2) were formed after pyrolysis,the solid solution structures and active components were disappeared after the deactivation of the anodes.Electrochemical results indicated that the active area decreased and the coating resistance increased,which are resulted by active component falling off from the anode surfaces.Hence,the deactivation of the …

The Optimal Sulfonation Conditions Of Self-Doped Polyaniline Obtained By Using Experimental Strategies, Wen-Yar Li, Chi-Chang Hu

Journal of Electrochemistry

The optimal sulfonation condition of self-doped sulfonated polyaniline(prepared from leucoemeraldinebase;denoted as LEB-SPANI) with a high electronic conductivity was obtained by experimental strategies,includingthe fractional factorial design(FFD) and central composite design(CCD).From the FFD experiment,the self-doped LEB-SPANI prepared at a lowtemperature(4oC),a short reaction time(1 h),and a small volume of fumingsulfuric acid(10 mL) showed a better conductivity(ca.127 mS/cm).In the CCD study coupled with a confirmationtest,the highest conductivity(ca.141 mS/cm) of the LEB-SPANI film was obtained under a sulfonation temperatureof 4oC,a sulfonation time of75 minutes,and a volume of8 mLof30% fuming sulfuric acid.The textural cha-racter-istics of self-doped LEB-SPANI were characterized by Fourier transform infrared(FTIR) spectroscopy,four-pointprobe method,and X-ray …

The High Temperature Corrosion Of 2205 Duplex Stainless Steel With Nacl Deposit, Fu-Fu Peng, Chaur-Jeng Wang, Yu-Chang Lin

Journal of Electrochemistry

The objective of this study was to figure out the hot corrosion behavior of 2205 duplex stainless steel(2205 DSS) within the temperature ranges from 550 to 850℃ in the static air condition with 2 mg/cm~(2)NaCl deposit,and in the air atmosphere condition with a constant flow rate of 500 vppm NaCl_((g)),respectively.Experimental results show that the hot corrosion kinetics met the parabolic rate law and the corrosion rate increased constantly with increasing temperature.The scales formed included Fe_(2)O_(3)/Fe_(3)O_(4)/Cr_(2)O_(3) and FeCr_(2)O_(4)from outer layer to inner layer.The sequence of formation is independent of the environment temperature,but the SiO_2 and NiO can be found in the …

A Study Of Three Corrosion Inhibitors For Reinforcing Steel In Sps Solution By Electrochemical Methods, Bing Zhao, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

Some electrochemical techniques such as linear polarization,electrochemical noise and EIShave been employedto study the inhibition behavior of N-lauroyl sarcosinate,β-sodium glycerophosphate and D-sodium gluconate for the reinforcing steel immersed in simulated concrete pore solution(SPS) with NaCl addition.The results show that D-sodium gluconatehas an obvious inhibitive effect for the reinforcing steelin containingCl~(-)SPS solution.It has been proposed that the corrosion inhibition of D-sodium gluconate is due to its competitive adsorption and precipitation on steel surface in the simulated concrete environment.

Electrochemical Oxidation Of Organic Additives In Tin Plating Electrolytes, Yin-Mei Cheng, Lan-Kun Cai, Qiang Song

Journal of Electrochemistry

Cyclic voltammetry(CV) was used to characterize the voltammetric behaviours of organic additives,e.g.PSA(phenolsulfonic acid)、EN(ethoxylatedα-naphthol) and ENSA(ethoxylatedα-naphthol sulfonic acid),on the anode surface.In PSA solutions,an anodic peak was obtained and the peak potential was about 1.2V.In EN and ENSA solutions,two anodic peaks were obtained and the peak potentials were about(0.95V) and 1.3V.The products of galvanostatic electrolysis were separated by HPLC(high performance liquid chromatography) and analyzed by EI/MS(electron ionizing mass spectrometry).The mechnism of the electrochemical oxidation was also disussed.

The Research Of Nano-Sized Nio Anode Materials For Lithium Ion Batteries, Jun-Mei Yan, Jing Zhang, Yong Yang

Journal of Electrochemistry

The nano-sized NiO materials were synthesized by solid phase method and sol-gel method. The synthesis conditions were optimized by DSC and TG techniques. The sol-gel method was optimized by changing the solvent and regulating the solution's pH for preparing NiO material. The structure and morphology of the materials were also characterized by means of XRD and TEM techniques, and the electrochemical performances of the materials were studied by the galvanostatically charge and discharge experiments.

Cyclic Voltammetry And Surface Enhanced Raman Spectroscopy Of Dissociative Adsorption Of Ethanol On Pt-Ru Electrodes, Zhang Bin

Journal of Electrochemistry

The behaviors of dissociative adsorption of ethanol on roughened platinum-ruthenium electrode with high activity of SERS were studied by using cyclic voltammetry and in-situ surface enhanced Raman spectroscopy, surface enhanced Raman spectra of dissociative adsorption of ethanol on Pt electrode in acid was obtained for the first time. It is shown that the Pt-Ru could lower the over-potential of CO oxidation when compared to Pt electrode. The results show that the ethanol in acid medium can be self-dissociated at Pt-Ru electrode to produce CO, which discourage the further oxidation of ethanol, some information of Pt-C and Pt-C-Pt stretching vibration from …

Adsorption Of Polyaspartic Acid From Sulphur Acid Solution On Carbon Steel And Its Corrosion Inhibition, Rong-Jing Cui, Ning Gu, Chun-Mei Li

Journal of Electrochemistry

The role of Polyaspartic acid in the corrosion inhibition of 45~(#) carbon steel in sulphuric acid solution has been investigated by polarization curve andelectrochemical impedance spectroscopy (EIS). The influences of the concentration and the temperature of PASP on the corrosion inhibition efficiency were determined. The results indicated that the PASP as the corrosion inhibitor mainly inhibitated the anode; within the experiment temperature, the inhibitor efficiency decreased with the raising of the temperature and PASP had a good inhibiting performance at 10℃, the corrosion inhibition efficiency of PASP for carbon steel increased with the increase of the concentration of PASP when …

Surface-Enhanced Raman Spectra Of Cytosine Adsorbed On A Roughened Gold Electrode, Yuan-Fei Wu, Jian-Feng Li, De-Yin Wu, Bin Ren, Zhong-Qun Tian

Journal of Electrochemistry

Cytosine adsorbed on a roughened gold electrode has been investigated by using electrochemical cyclic voltammetry and surface-enhanced Raman spectroscopy (SERS). The results indicate that cytosine was adsorbed on the Au electrode in a perpendicular orientation via the N3 position. As the maximum enhancement of ring breathing mode appears at negative potentials compared with other modes, both the electromagnetic enhancement and the charge transfer mechanism were considered to contribute to the SERS intensity. The binding interaction between cytosine and the gold electrode was weakened when the potential was negatively moved. The result also indicates that the SERS technique can be used …

Effect Of Chloride Ions On The Corrosion Behavior Of Reinforcing Steel In Simulated Concrete Pore Solutions, Yu Liu, Rong-Gui Du

Journal of Electrochemistry

The potentiodynamic anodic polarization was used to study the corrosion behavior of the reinforcing steel in simulated concrete pore solutions with different pH and chloride ion concentrations. The effect of chloride ions on passivity breakdown of the steel was examined by measuring the breaking potentials of reinforcing steel, and the critical chloride concentrations for depassivation were found in simulated concrete pore solutions at pH 12.50 and pH 12.00.

Nafion Emulsion Method For Fuel Cell Membrane-Electrode-Assembly Preparation, Chao-Yang Xia, Lin Zhuang

Journal of Electrochemistry

A Nafion emulsion method for fuel cell membrane-electrode-assembly (MEA) preparation was reported for the first time in this paper. 5 %(by mass) Nafion alcohol solution and non-polar solvent (e.g., cyclohexane) were ultrasonicallymixed to produce Nafion emulsion. The catalyst ink prepared using the thus-obtained Nafion emulsion can be directly cast onto Nafion membrane to make MEA. This method is simple in operation, and effectively preventsthe Nafion membrane swelling, hence is suitable for large-scale application. The MEA thus-prepared showed comparable catalyst efficiencywith respect to the popular transfer-method, and the preliminary performance in room-temperature H_(2)/O_(2 )fuel cell test was satisfying.

Research Progresses In A Flow Redox Battery, Quan-Feng Dong

Journal of Electrochemistry

As a large scale electrochemical storage device, flow redox battery in which the active materials are flowing electrolytes is different from the common batteries employing solid or gas materials as an electrode. In this paper we introduced flow redox battery in brief, reviewed its development and actual state on (study). The main problem existed in the new device was discussed when viewed with its future developments.

Surface And Sructure Investigations Of Membrane Electrode Assembly In Dmfc Lifetime Testing~*, Chengxuan Chengxuan, Cheng Peng, Meng-Di You, Jing Liu, Ying Zhang

Journal of Electrochemistry

The lifetime and performance of a direct methanol fuel cell (DMFC) were investigatedto understand the correlation between thestructure of catalysts /membrane and cell performanceversus time.The cell polarization and performance curves were obtained during the DMFC operation with the time.The catalysts and Nafion~ membrane of the membrane electrode assembly (MEA) from the lifetime test were comprehensively examined by XRD, HRTEM, FTIRand Raman spectroscope techniques.The results revealed that there was significant performance degradation during the first 200 hours operation; while the degradation was slowing down between 200 and 704hours operation.The degradation became worse after 1 002 h operation.The increases of the catalyst …

Effects Of Aluminide And Platinum-Aluminide Coatings On The Hot Corrosion Behavior Of Mar-M247 Nickel-Based Superalloy, I.K. Lee

Journal of Electrochemistry

This study is to investigate the high temperature hot corrosion behavior of aluminide coating and platinum-aluminide coating on Ni-base superalloy MAR-M247. On the platinum-aluminide, aluminide and the base metal, respectively, by the salt spraying method. The resistances to hot corrosion of platinum-aluminide coating, aluminide coating and the base metal were evaluated by the variations of weight gains. Aluminide and platinum-aluminide coating showed significanty beneficial effect on inhibiting the hot corrosion of MAR-M247. But that of the platinum-aluminide coating was even much better. The aluminide coating surface was composed of β-NiAl, and that of the platinum-aluminide coating was PtAl_(2). Both two …

The Application Of Astm C1202-93 On Evaluating The Performance Of Anti-Corrosion Of Concrete, Yuan Chen Yuan

Journal of Electrochemistry

The test of chloride ion penetration based on the standards of ASTM C1202-93 is applied to evaluate the anti-corrosion performance of concrete in this research. Concrete specimens were produced according to ACI 318-89 mixture proportioning design and the Desenfied Mixture Design Algorithm (DMDA) and were measured the 6-hour coulombs at the age of 91 days. Results show that w/b is not the factor influencing chloride penetration of ACI concrete, as the ion penetration of ACI specimens is all higher than 2 000 Coulombs and can even be poorer than 10 000 Coulombs. With a proper amount of pozzolanic material, the …

A Conjugate Dissolution / Deposition Behavior In Thin Layer Electrodeposition, Sun Bin

Journal of Electrochemistry

During the electrodeposition of lead, the dendrite deposit segregates from the cathode due to the disturbance of hydrogen gas. The segregated deposit could move toward the anode spontaneously rather than keep stationary. The studies show that this novel phenomenon was caused by the conjugate electrodissolution and electrodeposition reactions taking place at two ends of the isolated segment of the deposit. The mechanism inducing this phenomenon is suggested.

Corrosion Behavior Of Sml,Erw Pipeline Steels Exposed To Seamud, Wei Hua

Journal of Electrochemistry

The corrosion behavior of API Spec X60 pipeline steels, including electric resistance welding(ERW) and Seamless (SML) types,in sea mud gathered fromYangtse River estuaryof the East China Sea was investigatedthrough linear polarization resistance, potentio-dynamic polarizationand electrochemical impedance measurements.The result indicate the improved corrosion resistance of SML in sea mud. The oxygen diffusion in the cathode zone determines the corrosion behavior of pipeline steel in sea mud.