Open Access. Powered by Scholars. Published by Universities.®

Engineering Science and Materials Commons™

Open Access. Powered by Scholars. Published by Universities.®

PDF

Air Force Institute of Technology

Discipline
Keyword
Publication Year
Publication
Publication Type

Articles 1 - 30 of 144

Full-Text Articles in Engineering Science and Materials

The Behavior Of ½⟨111⟩ Screw Dislocations In W–Mo Alloys Analyzed Through Atomistic Simulations, Lucas A. Heaton, Kevin Chu, Adib J. Samin Feb 2024

The Behavior Of ½⟨111⟩ Screw Dislocations In W–Mo Alloys Analyzed Through Atomistic Simulations, Lucas A. Heaton, Kevin Chu, Adib J. Samin

Faculty Publications

Analyzing plastic flow in refractory alloys is relevant to many different commercial and technological applications. In this study, screw dislocation statics and dynamics were studied for various compositions of the body-centered cubic binary alloy tungsten–molybdenum (W–Mo). The core structure did not appear to change for different alloy compositions, consistent with the literature. The pure tungsten and pure molybdenum samples had the lowest plastic flow, while the highest dislocation velocities were observed for equiatomic, W0.5Mo0.5 alloys. In general, dislocation velocities were found to largely align with a well-established dislocation mobility phenomenological model supporting two discrete dislocation mobility regimes, …

Go to article

Residual Stress Generation In Additive Manufacturing Of Complex Lattice Geometries, Katie Bruggeman, Nathan Klingbeil, Anthony N. Palazotto Feb 2024

Residual Stress Generation In Additive Manufacturing Of Complex Lattice Geometries, Katie Bruggeman, Nathan Klingbeil, Anthony N. Palazotto

Faculty Publications

Residual stresses developed during additive manufacturing (AM) can influence the mechanical performance of structural components in their intended applications. In this study, thermomechanical residual stress simulations of the laser powder bed fusion (LPBF) process are conducted for both simplified (plate and cube-shaped) geometries as well as five complex lattice geometries fabricated with Inconel 718. These simulations are conducted with the commercial software package Simufact Additive©, which uses a nonlinear finite element analysis and layer-by-layer averaging approach in determining residual stresses. To verify the efficacy of the Simufact Additive© simulations, numerical results for the plate and cube-shape geometries are analyzed for …

Go to article

Impact Of Silicon Ion Irradiation On Aluminum Nitride-Transduced Microelectromechanical Resonators, David D. Lynes, Joshua Young, Eric Lang, Hengky Chandrahalim Nov 2023

Impact Of Silicon Ion Irradiation On Aluminum Nitride-Transduced Microelectromechanical Resonators, David D. Lynes, Joshua Young, Eric Lang, Hengky Chandrahalim

Faculty Publications

Microelectromechanical systems (MEMS) resonators use is widespread, from electronic filters and oscillators to physical sensors such as accelerometers and gyroscopes. These devices' ubiquity, small size, and low power consumption make them ideal for use in systems such as CubeSats, micro aerial vehicles, autonomous underwater vehicles, and micro-robots operating in radiation environments. Radiation's interaction with materials manifests as atomic displacement and ionization, resulting in mechanical and electronic property changes, photocurrents, and charge buildup. This study examines silicon (Si) ion irradiation's interaction with piezoelectrically transduced MEMS resonators. Furthermore, the effect of adding a dielectric silicon oxide (SiO2) thin film is …

Go to article

Adiabatic Shear Banding In Nickel And Nickel-Based Superalloys: A Review, Russell A. Rowe, Paul G. Allison, Anthony N. Palazotto, Keivan Davami Nov 2022

Adiabatic Shear Banding In Nickel And Nickel-Based Superalloys: A Review, Russell A. Rowe, Paul G. Allison, Anthony N. Palazotto, Keivan Davami

Faculty Publications

This review paper discusses the formation and propagation of adiabatic shear bands in nickel-based superalloys. The formation of adiabatic shear bands (ASBs) is a unique dynamic phenomenon that typically precedes catastrophic, unpredicted failure in many metals under impact or ballistic loading. ASBs are thin regions that undergo substantial plastic shear strain and material softening due to the thermo-mechanical instability induced by the competitive work hardening and thermal softening processes. Dynamic recrystallization of the material’s microstructure in the shear region can occur and encourages shear localization and the formation of ASBs. Phase transformations are also often seen in ASBs of ferrous …

Go to article

Monolithically Integrated Microscale Pressure Sensor On An Optical Fiber Tip, Jeremiah C. Williams, Hengky Chandrahalim May 2022

Monolithically Integrated Microscale Pressure Sensor On An Optical Fiber Tip, Jeremiah C. Williams, Hengky Chandrahalim

AFIT Patents

A passive microscopic Fabry-Pérot Interferometer (FPI) pressure sensor includes an optical fiber and a three-dimensional microscopic optical enclosure. The three-dimensional microscopic optical enclosure includes tubular side walls having lateral pleated corrugations and attached to a cleaved tip of the optical fiber to receive a light signal. An optically reflecting end wall is distally engaged to the tubular side walls to enclose a trapped quantity of gas that longitudinally positions the optically reflecting end wall in relation to ambient air pressure, changing a distance traveled by a light signal reflected back through the optical fiber.

Go to article

Method Of Making Hinged Self-Referencing Fabry–Pérot Cavity Sensors, Jeremiah C. Williams, Hengky Chandrahalim Mar 2022

Method Of Making Hinged Self-Referencing Fabry–Pérot Cavity Sensors, Jeremiah C. Williams, Hengky Chandrahalim

AFIT Patents

A method is provided for fabricating a passive optical sensor on a tip of an optical fiber. The method includes perpendicularly cleaving a tip of an optical fiber and mounting the tip of the optical fiber in a specimen holder of a photosensitive polymer three-dimensional micromachining machine. The method includes forming a three-dimensional microscopic optical structure within the photosensitive polymer that comprises a two cavity Fabry-Perot Interferometer (FPI) having a hinged optical layer that is pivotally coupled to a suspended structure. The method includes removing an uncured portion of the photosensitive polymer using a solvent. The method includes depositing a …

Go to article

Computational Based Investigation Of Lattice Cell Optimization Under Uniaxial Compression Load, Derek G. Spear, Jeremiah S. Lane, Anthony N. Palazotto, Ryan A. Kemnitz Mar 2022

Computational Based Investigation Of Lattice Cell Optimization Under Uniaxial Compression Load, Derek G. Spear, Jeremiah S. Lane, Anthony N. Palazotto, Ryan A. Kemnitz

Faculty Publications

Structural optimization is a methodology used to generate novel structures within a design space by finding a maximum or minimum point within a set of constraints. Topology optimization, as a subset of structural optimization, is often used as a means for light-weighting a structure while maintaining mechanical performance. This article presents the mathematical basis for topology optimization, focused primarily on the Bi-directional Evolutionary Structural Optimization (BESO) and Solid Isotropic Material with Penalization (SIMP) methodologies, then applying the SIMP methodology to a case study of additively manufactured lattice cells. Three lattice designs were used: the Diamond, I-WP, and Primitive cells. These …

Go to article

Thermal Relaxation Of Shot Peen Induced Residual Stresses In A Nickel-Base Superalloy, Bryce E. Van Velson Mar 2022

Thermal Relaxation Of Shot Peen Induced Residual Stresses In A Nickel-Base Superalloy, Bryce E. Van Velson

Theses and Dissertations

Shot peening induces compressive residual stresses in components that positively influence fatigue life. Thermal and mechanical loading causes those residual stresses to relax. The hole drilling method and xray diffraction is used to measure the thermal relaxation of residual stresses in the nickel-base superalloy ME3.

Go to article

Design And Testing Of A Composite Compressor Rotor, Mauro Noel V. De Leon Mar 2022

Design And Testing Of A Composite Compressor Rotor, Mauro Noel V. De Leon

Theses and Dissertations

Additive manufacturing (AM) and molding are manufacturing methods known for building representations or replicas of conceptualized engine components, but was considered impractical for manufacturing operating engine components. More recent technology has rendered composite materials (combining high-temperature polymers and fiber reinforcement) capable of withstanding the temperature and structural requirements to compete with conventional turbomachinery metals. This study explores the application of several high-temperature polymers (ULTEM 9085, Onyx-Carbon fiber, and Epoxy-Carbon fiber) and their survivability in the operating conditions of a P400 Engine compressor. The tests conducted for this study determined their viability as compressor materials. This study required conducting tensile specimen …

Go to article

A Study On The Early Stages Of Degradation Of Multi-Component Alloy Surfaces In Extreme Environments Using The Multi-Cell Monte Carlo Method, Tyler D. Dolezal Mar 2022

A Study On The Early Stages Of Degradation Of Multi-Component Alloy Surfaces In Extreme Environments Using The Multi-Cell Monte Carlo Method, Tyler D. Dolezal

Theses and Dissertations

A computational toolset is presented and used in two examples that examined the interactions between structural materials and their extreme environments. A multi-cell Monte Carlo algorithm was developed to generate thermodynamically realistic solid-state alloy systems. These structures served as the foundation upon which surface slab models were generated. The tedious procedure of generating surface slab models from bulk structures was automated. The tools were used to study the high temperature surface corrosion resistance of a high-entropy alloy, Al10Nb15Ta5Ti30Zr40, and a nickel-based alloy, Ni70Nb10W20, under …

Go to article

Method Of Making Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith Oct 2021

Method Of Making Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith

AFIT Patents

A method of making passive microscopic Fabry-Pérot Interferometer (FPI) sensor includes forming a three-dimensional microscopic optical structure on a cleaved tip of an optical fiber that reflects a light signal back through the optical fiber. The reflected light is altered by refractive index changes in the three-dimensional structure that is subject to at least one of: (i) thermal radiation; and (ii) volatile organic compounds.

Go to article

Evaluation Of Additively Manufactured Lattices Under High Strain Rate Impact, Derek G. Spear Sep 2021

Evaluation Of Additively Manufactured Lattices Under High Strain Rate Impact, Derek G. Spear

Theses and Dissertations

Several additively manufactured lattice designs and configurations were evaluated under compression loads under various strain rates from quasi-static to highly dynamic. These experiments examined how the mechanical behavior of the lattice changed based on the lattice design properties and the applied strain rates. The modulus of elasticity, yield strength, plateau stress, and toughness were observed to decrease with an increase in strain rate, revealing that the lattice designs exhibit a negative strain rate sensitivity. A new lattice flow stress model was developed to account for the mechanical response of the lattice and was incorporated into a computational model for simulation. …

Go to article

Investigation And Statistical Modeling Of The Mechanical Properties Of Additively Manufactured Lattices, Derek G. Spear, Anthony N. Palazotto Jul 2021

Investigation And Statistical Modeling Of The Mechanical Properties Of Additively Manufactured Lattices, Derek G. Spear, Anthony N. Palazotto

Faculty Publications

This paper describes the background, test methodology, and experimental results associated with the testing and analysis of quasi-static compression testing of additively manufactured open-cell lattice structures. The study aims to examine the effect of lattice topology, cell size, cell density, and surface thickness on the mechanical properties of lattice structures. Three lattice designs were chosen, the Diamond, I-WP, and Primitive Triply Periodic Minimal Surfaces (TPMSs). Uniaxial compression tests were conducted for every combination of the three lattice designs, three cell sizes, three cell densities, and three surface thicknesses. In order to perform an efficient experiment and gain the most information …

Go to article

Shock Migration On An Oscillating Straked Delta Wing Using An Unsteady Euler Solver, Alexander J. Brown Mar 2021

Shock Migration On An Oscillating Straked Delta Wing Using An Unsteady Euler Solver, Alexander J. Brown

Theses and Dissertations

This research contributes to the understanding of Shock Induced Trailing Edge Separation (SITES) as a driver of Limit Cycle Oscillation (LCO) by performing a computational investigation of nonlinear aerodynamic phenomena on a straked delta wing in transonic flow, oscillating in pitch. ZEUS, an Euler-based aeroelastic solver with a boundary layer coupling scheme meant to capture viscous flow effects within the boundary layer, was used to analyze aerodynamic flow around the wing for various mean incidence angles, oscillation amplitudes, and Mach numbers within the transonic region. The dynamic characteristics of the airflow around the wing were investigated in order to characterize …

Go to article

Experimental And Computational Analysis Of Progressive Failure In Bolted Hybrid Composite Joints, John S. Brewer Dec 2020

Experimental And Computational Analysis Of Progressive Failure In Bolted Hybrid Composite Joints, John S. Brewer

Theses and Dissertations

Composite materials are strong, lightweight, and stiff making them desirable in aerospace applications. However, a practical issue arises with composites in that they behave unpredictably in bolted joints, where damage and cracks are often initiated. This research investigated a solution to correcting the problem with composite bolted joints. A novel hybrid composite material was developed, where thin stainless steel foils were placed between and in place of preimpregnated composite plies during the cure cycle to reinforce stress concentrations in bolted joints. This novel composite was compared to control samples experimentally in quasi-static monotonic loading in double shear configuration in 9-ply …

Go to article

Tension-Tension Fatigue Behavior Of Nextel™ 720/Alumina-Mullite Ceramic Composite At 1200°C In Air And In Steam, Sarah A. Witzgall Jun 2020

Tension-Tension Fatigue Behavior Of Nextel™ 720/Alumina-Mullite Ceramic Composite At 1200°C In Air And In Steam, Sarah A. Witzgall

Theses and Dissertations

Uniaxial tension-tension fatigue performance of an oxide-oxide continuous fiber ceramic composite was studied at 1200°C in laboratory air and in steam. The composite is reinforced with laminated, 0/90 mullite/alumina (NEXTEL™720) fibers woven in an eight-harness satin weave and has a porous alumina/mullite matrix. There is no interphase between the fiber and matrix. The composite relies on the porous matrix for crack deflection and flaw tolerance. Tension-tension fatigue was examined for maximum stresses of 45 – 136 MPa in air and in steam. To assess the effects of the steam environment on fatigue performance, experimental results obtained in air are compared …

Go to article

Modeling Nonlinear Heat Transfer For A Pin-On-Disc Sliding System, Brian A. Boardman Mar 2020

Modeling Nonlinear Heat Transfer For A Pin-On-Disc Sliding System, Brian A. Boardman

Theses and Dissertations

The objective of this research is to develop a numerical method to characterize heat transfer and wear rates for samples of Vascomax® 300, or Maraging 300, steel. A pin-on-disc experiment was conducted in which samples were exposed to a high-pressure, high-speed, sliding contact environment. This sliding contact generates frictional heating that influences the temperature distribution and wear characteristics of the test samples. A two-dimensional nonlinear heat transfer equation is discretized and solved via a second-order explicit finite difference scheme to predict the transient temperature distribution of the pin. This schematic is used to predict the removal of material from the …

Go to article

Focused Beam System Biaxial Material Characterization, Nicholas A. O'Gorman Mar 2020

Focused Beam System Biaxial Material Characterization, Nicholas A. O'Gorman

Theses and Dissertations

Electromagnetic material characterization is the process of determining the constitutive parameters (complex permittivity and permeability) of given a sample. Due to the large number of unknowns involved, multiple unique measurements are required for material property extraction. Many measurement methods, such as waveguides and striplines, possess a rigid internal structure that the sample being measured must adhere to. This rigidity limits these methods to samples that fit within the device and inhibits oblique sample orientations, limiting the number of independent measurements that can be obtained. A focus beam system, due to being an open system with greater freedom in sample size …

Go to article

Structural Dynamic And Inherent Damping Characterization Of Additively Manufactured Airfoil Components, Andrew W. Goldin Mar 2020

Structural Dynamic And Inherent Damping Characterization Of Additively Manufactured Airfoil Components, Andrew W. Goldin

Theses and Dissertations

The push for low cost and higher performance/efficient turbine engines have introduced a new demand for novel technologies to improve robustness to vibrations resulting in High Cycle Fatigue (HCF). There have been many proposed solutions to this, some passive and some active. With the advent of Additive Manufacturing (AM), new damping techniques can now be incorporated directly into the design and manufacture process to suppress the vibrations that create HCF. In this study, this novel unfused pocket damping technology is applied to a blade structure and the resulting damping effectiveness is quantified. The application of this technology to complex geometries …

Go to article

Fatigue Behavior Of An Advanced Melt-Infiltrated Sic/Sic Composite With Environmental Barrier Coating At 1200°C In Air And In Steam, Thaddeus M. Williams Mar 2020

Fatigue Behavior Of An Advanced Melt-Infiltrated Sic/Sic Composite With Environmental Barrier Coating At 1200°C In Air And In Steam, Thaddeus M. Williams

Theses and Dissertations

Advanced aerospace applications such as aircraft turbine engine components, hypersonic flight vehicles, and spacecraft reentry thermal protection systems require structural materials that have superior long-term mechanical properties under high temperature, high pressure, and varying environmental factors, such as moisture. Because of their low density, high strength and fracture toughness at high temperatures SiC fiber-reinforced SiC matrix composites are being evaluated for aircraft engine hot-section components. In these applications the composites will be subjected to various types of mechanical loadings at elevated temperatures in oxidizing environments. Because their constituents are intrinsically oxidation-prone, the most significant problem hindering SiC/SiC composites is oxidation …

Go to article

Homotopy Simulation Of Dissipative Micropolar Flow And Heat Transfer From A Two-Dimensional Body With Heat Sink Effect: Applications In Polymer Coating, O. A. Bég, B. Vasu, A. K. Ray, T. A. Beg, A. Kadir, H. J. Leonard, Rama S. R. Gorla Jan 2020

Homotopy Simulation Of Dissipative Micropolar Flow And Heat Transfer From A Two-Dimensional Body With Heat Sink Effect: Applications In Polymer Coating, O. A. Bég, B. Vasu, A. K. Ray, T. A. Beg, A. Kadir, H. J. Leonard, Rama S. R. Gorla

Faculty Publications

Non-Newtonian flow from a wedge constitutes a fundamental problem in chemical engineering systems and is relevant to processing of polymers, coating systems, etc. Motivated by such applications, the homotopy analysis method (HAM) was employed to obtain semi-analytical solutions for thermal convection boundary layer flow of incompressible micropolar fluid from a two-dimensional body (wedge). Viscous dissipation and heat sink effects were included. The non-dimensional boundary value problem emerges as a system of nonlinear coupled ordinary differential equations, by virtue of suitable coordinate transformations. The so-called Falkner-Skan flow cases are elaborated. Validation of the HAM solutions was achieved with earlier simpler models, …

Go to article

Quantifying The Effects Of Hyperthermal Atomic Oxygen And Thermal Fatigue Environments On Carbon Nanotube Sheets For Space-Based Applications, Jacob W. Singleton, Gregory R. Cobb, Heath E. Misak, Ryan A. Kemnitz Oct 2019

Quantifying The Effects Of Hyperthermal Atomic Oxygen And Thermal Fatigue Environments On Carbon Nanotube Sheets For Space-Based Applications, Jacob W. Singleton, Gregory R. Cobb, Heath E. Misak, Ryan A. Kemnitz

Faculty Publications

The effects of atomic oxygen and thermal fatigue on two different types of carbon nanotube sheets were studied. One set was treated with nitric acid, while the other set was left untreated. Monotonic tensile tests were performed before and after exposure to determine the effects of either exposure type on the sheets’ mechanical properties. Electrical conductivity and electromagnetic interference measurements were recorded to determine the effects of AO-exposure and thermal cycling on the sheets’ electrical properties. Neither exposure type affected the sheets’ specific strengths. Both exposure types increased the sheets’ specific stiffnesses and decreased the sheets’ strains at failure. The …

Go to article

Effects Of Carbon-Based Ablation Products On Hypersonic Boundary Layer Stability, Olivia S. Elliott Sep 2019

Effects Of Carbon-Based Ablation Products On Hypersonic Boundary Layer Stability, Olivia S. Elliott

Theses and Dissertations

Hypersonic vehicles require an accurate prediction of the transition of the boundary layer for the design of the thermal protection system due to the high heating rates under turbulent flow. Many thermal protection systems are carbon-based and introduce new species, specifically CO2, into the boundary layer flow which are known to dampen the instabilities that lead to transition for hypersonic vehicles. A Computation Fluid Dynamics study was accomplished examining the concentration of CO2 required to impact boundary layer transition over both sharp and blunt cones. These results were used in conjunction with air-carbon ablation models models to …

Go to article

On The Pulsed Laser Ablation Of Metals And Semiconductors, Todd A. Van Woerkom Aug 2019

On The Pulsed Laser Ablation Of Metals And Semiconductors, Todd A. Van Woerkom

Theses and Dissertations

This dissertation covers pulsed laser ablation of Al, Si, Ti, Ge, and InSb, with pulse durations from tens of picosecond to hundreds of microseconds, fluences from ones of J/cm2 to over 10,000 J/cm2, and in ambient air and vacuum. A set of non-dimensional scaling factors was created to interpret the data relative to the laser and material parameters, and it was found that pulse durations shorter than a critical timescale formed craters much larger than the thermal diffusion length, and longer pulse durations created holes much shallower than the thermal diffusion length. Low transverse order Gaussian beams …

Go to article

Influence Of Leading Edge Oscillatory Blowing On Time-Accurate Dynamic Store Separation, Ryan G. Saunders Mar 2019

Influence Of Leading Edge Oscillatory Blowing On Time-Accurate Dynamic Store Separation, Ryan G. Saunders

Theses and Dissertations

The primary objective of this research is to support the static and dynamic characterization and the time-accurate dynamic load data acquisition of store separation from a cavity with leading edge oscillatory blowing. Developing an understanding of, and potentially controlling, pitch bifurcation of a store release is a motivation for this research. The apparatus and data acquisition system was used in a two-part experiment to collect both static and dynamic testing data in the AFIT low speed wind tunnel in speeds of 60, 100, and 120 mph, from Reynolds numbers varying from 5.5x104 to 4.6x105, depending on reference …

Go to article

Tracking Shock Movement On The Surface Of An Oscillating, Straked Semispan Delta Wing, Justin A. Pung Mar 2019

Tracking Shock Movement On The Surface Of An Oscillating, Straked Semispan Delta Wing, Justin A. Pung

Theses and Dissertations

A recent research effort, sponsored by the Air Force Office of Scientific Research, numerically investigated the unsteady aerodynamic flow field around an oscillating, straked, delta wing. The study was centered on determining the importance of the unsteady aerodynamic forces acting as a driver for a nonlinear motion known as limit cycle oscillations. The current effort focused on creating a computational model to compare to the results of previous tests and modeling efforts and discover new information regarding the onset of LCO. The computational model was constructed using the Cartesian overset capabilities of the CREATE-AV™ fixed wing fluid dynamics solver Kestrel. …

Go to article

Manufacture Of Fused Deposition Modeling Joints Using Ultem 9085, Zane A. Willburn Mar 2019

Manufacture Of Fused Deposition Modeling Joints Using Ultem 9085, Zane A. Willburn

Theses and Dissertations

The manufacture of joints between a base structure and a structure manufactured via Fused Deposition Modeling (FDM) will be investigated. ULTEM 9085, a high temperature plastic with potential aerospace applications, will be the material used. The specific application this research is focused on is a robotic and mobile FDM printer capable of building structures onto other structures in space. A joint will be formed by fusing the base layer of the printed structure and the top of the base structure together. Tensile testing will be performed to determine the strength of the bond between parts. Tensile specimens will be manufactured …

Go to article

Analytical Models And Control Design Approaches For A 6 Dof Motion Test Apparatus, Kyra L. Schmidt Mar 2019

Analytical Models And Control Design Approaches For A 6 Dof Motion Test Apparatus, Kyra L. Schmidt

Theses and Dissertations

Wind tunnels play an indispensable role in the process of aircraft design, providing a test bed to produce valuable, accurate data that can be extrapolated to actual flight conditions. Historically, time-averaged data has made up the bulk of wind tunnel research, but modern flight design necessitates the use of dynamic wind tunnel testing to provide time-accurate data for high frequency motion. This research explores the use of a 6 degree of freedom (DOF) motion test apparatus (MTA) in the form of a robotic arm to allow models inside a subsonic wind tunnel to track prescribed trajectories to obtain time-accurate force …

Go to article

Ballistic Evaluation Of Carbon Nanotube Sheet Material In Multifunctional Applications, Casey M. Keilbarth Mar 2019

Ballistic Evaluation Of Carbon Nanotube Sheet Material In Multifunctional Applications, Casey M. Keilbarth

Theses and Dissertations

Significant development of carbon nanotubes has occurred since they were first studied in the 1990's. Attempts to capture the phenomenal molecular properties in practical applications are gaining ground as new methods of producing CNTs have been developed. This thesis sought to determine if the addition of commercially produced CNT sheets to thin carbon fiber panels improved the ballistic properties of the panel. The difference between 0 and 4 CNT sheets was studied. The hypothesis was that inte- grating CNT sheets into the laminate would increase the projectile energy absorbed by the panel and reduce the damage to the panel incurred …

Go to article

Computational Aerothermodynamic Analysis Of Satellite Trans-Atmospheric Skip Entry Survivability, John J. Runco Mar 2019

Computational Aerothermodynamic Analysis Of Satellite Trans-Atmospheric Skip Entry Survivability, John J. Runco

Theses and Dissertations

Computational aerothermodynamic analysis is presented for a spacecraft in low Earth orbit performing an atmospheric skip entry maneuver. Typically, atmospheric reentry is a terminal operation signaling mission end-of-life and, in some instances, executed for spacecraft disposal. A variation on reentry – skip entry – is an aeroassisted trans-atmospheric maneuver in which a spacecraft utilizes the effects of aerodynamic drag in order to reduce energy prior to a terminal entry, pinpoint a targeted entry, or change orbital elements such as inclination. Spacecraft performing a skip entry enable new modes of maneuver to enhance operations in nominal or possibly contested mission environments. …

Go to article

Next Last