Engineering Science and Materials Commons^™

Development Of Engineered Cementitious Composites With Conductive Inclusions For Use In Self-Sensing Applications, Benny Suryanto Dr, Danah Saraireh Ms, Steven Walls Mr, Jaehwan Kim Dr, W John Mccarter Prof

International Conference on Durability of Concrete Structures

The mechanical and a.c. electrical properties of a new varietal of engineered cementitious composite (ECC) incorporating conductive inclusions are presented. Electrical measurements were undertaken over a wide frequency range while curing and when under uniaxial tensile loading to study the influence of ongoing hydration and multiple microcrack formation on the composite electrical impedance. When presented in Nyquist format, the work shows that conductive inclusions reduce the bulk resistance of the composite while enhancing its polarizability, transforming the classic, single-arc bulk response of typical cement-based materials to a two-arc response. The bulk resistance was shown to increase with time and damage, …

Finite Element Simulation Of Bonded And Mechanically Anchored Shear Interfaces Of Externally Applied Frp Sheets To Concrete And Wood-Concrete Composites, Alaa Al-Sammari

Doctoral Dissertations

Composite construction is prevalent in advanced structural systems where components of different materials are combined in the same structure to improve the performance of strong and economic structural sections. Maintaining continuity between the different structural components to produce monolithic structural behavior is challenging because of differences in the mechanical properties of these materials in terms of stiffness, strength, and ductility. The different components of the composite section are typically joined using adhesives and/or mechanical anchors to produce partial or full composite action. This dissertation discusses two types of shear interfaces intended to result in structural composite behavior. The first type …

Northeastern Species In Hybrid Cross Laminated Timber, Hamid Kaboli

Doctoral Dissertations

Known in the building industry throughout the world, Cross Laminated Timber (CLT) is a massive timber building material with outstanding structural, fire, and seismic properties. CLT is a cost-competitive, sustainable construction material is a good candidate as a substitute material for concrete, masonry, and steel, in mid-rise and high-rise buildings. CLT is perpendicular layers of dimensional lumbers usually laminated together and forming a massive structural panel. This dissertation explores the viability of utilizing Massachusetts grown Eastern Hemlock and Eastern White Pine in CLT panels as pure or in conjunction with other high-value wood products. 59% of Massachusetts’ lands are covered …

Structural Health Monitoring Of Composite Parts: A Review, Jacob Pessin

Honors Theses

Structural health monitoring has the potential to allow composite structures to be more reliable and safer, then by using more traditional damage assessment techniques. Structural health monitoring (SHM) utilizes individual sensor units that are placed throughout the load bearing sections of a structure and gather data that is used for stress analysis and damage detection. Statistical time based algorithms are used to analyze collected data and determine both damage size and probable location from within the structure. While traditional calculations and life span analysis can be done for structures made of isotropic materials such as steel or other metals, composites …

Application Of Computational Tools To Spaghetti-Based Truss Bridge Design, Jin Xu, Jiliang Li, Nuri Zeytinoglu, Jinyuan Zhai

ASEE IL-IN Section Conference

Application of Computational Tools to Spaghetti-Based Truss Design

Statics and Strength of Materials are two foundational courses for Mechanical/Civil Engineering. In order to assist students in better understanding and applying concepts to a meaningful design task, SolidWorks and theoretical calculation were used for a spaghetti-bridge design contest with the constraints of given maximum weight and allowable support-material weight. As the first step of this iterative designing process, both extrude feature and structural member were introduced to model planar bridge trusses. Then SolidWorks’ Statics module was used to run FEA analysis of the structural performance in efforts to optimize the …

In Situ Mechanical Characterization Of The Mixed- Mode Fracture Strength Of The Cu/Si Interface For Tsv Structures, Chenglin Wu, Congjie Wei, Yanxiao Li

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In situ nanoindentation experiments have been widely adopted to characterize material behaviors of microelectronic devices. This work introduces the latest developments of nanoindentation experiments in the characterization of nonlinear material properties of 3D integrated microelectronic devices using the through-silicon via (TSV) technique. The elastic, plastic, and interfacial fracture behavior of the copper via and matrix via interface were characterized using small-scale specimens prepared with a focused ion beam (FIB) and nanoindentation experiments. A brittle interfacial fracture was found at the Cu/Si interface under mixed-mode loading with a phase angle ranging from 16.7° to 83.7°. The mixed-mode fracture strengths were extracted …