Engineering Science and Materials Commons^™

Numerical Simulation Of Multi-Phase Core-Shell Molten Metal Drop Oscillations, Kaushal Sumaria

Masters Theses

The surface tension of liquid metals is an important and scientifically interesting parameter which affects many metallurgical processes such as casting, welding and melt spinning. Conventional methods for measuring surface tension are difficult to use for molten metals above temperatures of 1000 K. Containerless methods are can be used to measure the surface tension of molten metals above 1000 K. Oscillating drop method is one such method where a levitated droplet is allowed to undergo damped oscillations. Using the Rayleigh’s theory for the oscillation of force-free inviscid spherical droplets, surface tension and viscosity of the sample can be calculated from …

High Performance Silver Diffusive Memristors For Future Computing, Rivu Midya

Masters Theses

Sneak path current is a significant remaining obstacle to the utilization of large crossbar arrays for non-volatile memories and other applications of memristors. A two-terminal selector device with an extremely large current-voltage nonlinearity and low leakage current could solve this problem. We present here a Ag/oxide-based threshold switching (TS) device with attractive features such as high current-voltage nonlinearity (~10¹⁰), steep turn-on slope (less than 1 mV/dec), low OFF-state leakage current (~10^-14 A), fast turn ON/OFF speeds (<75/250 ns), and good endurance (>10⁸ cycles). The feasibility of using this selector with a typical memristor has been demonstrated by physically integrating them …

Development Of Lignin Carbon Fiber And Reinforced Composites, Nathan Kieran Meek

Masters Theses

The aim of this work is to develop lignin carbon fiber for composite applications. This included mechanical testing of single lignin carbon fiber (LCF), interfacial shear strength determination for LCF-resin systems using single fiber fragmentation, x-ray diffraction for the evaluation of microstructural parameters, and finally composite manufacturing and testing. Through these focused areas of analysis, the carbon fiber is thoroughly characterized and composite performance is evaluated. This effort was a collaboration with the Center for Renewable Carbon (CRC) and the Civil and Environmental Engineering Department. LCF produced by the CRC resulted in fibers having tensile strength of 250-800 MPa and …

Radiation-Induced Radicals In Polyurea-Crosslinked Silica Aerogel, Benjamin Michael Walters

Masters Theses

Free radicals are atoms or molecules with an odd number of electrons in an outer shell. Since electrons typically occur in pairs, this leaves one electron that is unpaired. In seek of another electron to pair with, free radicals react with and steal electrons from neighboring molecules, which then become free radicals themselves. This can start a chain reaction, cascading into large scale damage.

Ionizing radiation can tear through molecules, just as bullets can tear through things that we see. If free radicals can be detected, and seen to increase in a material upon radiation exposure, this can indicate molecular …

Effect Of Moisture Absorption On The Sinter Quality Of Central Solenoid (Cs) Coil Pack, Zeshaan Sher Mohammed

Masters Theses

Fusion energy has been said to be the solution to all the world’s energy problems. The International Thermonuclear Experimental Reactor (ITER) is the flagship project to demonstrate the feasibility of fusion energy. The Central Solenoid (CS), an important component of the reactor, is needed to induce plasma current, initiate, ramp-up, ramp-down, and sustain plasma in a very controlled manner. In order to achieve this, the CS coil packs must be manufactured under controlled conditions. The CS conductor is an advanced cable-in-conduit Nb3Sn superconductor. The CS cable will be made in long continuous sections but with thousands of meter of cable …

Radiation-Curable Adhesives For Wood Composites, Timothy H. Starr

Masters Theses

Wood composites are widely used in construction applications because of their superior dimensional and structural attributes over raw wood products. However, current wood composite manufacturing practices, which rely on thermal-curing of adhesives, are expensive, energy intensive, time consuming and are prone to manufacturing defects. Use of radiation curable adhesives (RCAs) could potentially answer all of these issues. Specifically, use of electron-beam (e-beam) radiation has been increasing in areas of research and industry where rapid, low-temperature polymerization is required and low energy consumption is desired. For e-beams to be used in wood composites, however, it must be determined whether or not …

A Study Of Irrigation, Fertigation And Plasticulture In Burley Tobacco, With A Focus On Yield, Quality And Tsna Reduction, Eric F. Caldwell

Masters Theses

Nitrogen fertilization is important in attaining high yielding, quality tobacco. However, practices that use excessive N can be uneconomical, threaten the environment and produce leaves that are high in nitrates. Leaves high in nitrates have been positively correlated with leaves that are high in tobacco specific nitrosamines (TSNA), which are considered potent carcinogens. Competition from cheaper, foreign leaf, increasing costs of fertilizers and new market structures which show purchasers seeking low TSNA leaf demand that producers become more efficient in their N use. The objective of this study is an examination of burley (TN 90) and dark (KY 171) tobacco …

Development Of A Methodology To Evaluate Environmental Implications Of Lean Implementation, Pamuk Teparakul

Masters Theses

While much research has confirmed the effectiveness of lean manufacturing in improving manufacturing productivity, far less work has focused on the impact of lean implementation on the different measures of environmental performance. More notably, there remains much to be understood about the complex relationship between lean manufacturing principles and their overall environmental impacts.

The purpose of this research is to develop a multi-phase methodology to assist practitioners in evaluating overall environmental impacts associated with implementation of various lean manufacturing principles. This knowledge would then allow practitioners to design and analyze manufacturing systems for both productivity and environmental concerns. A case …