Electrical and Computer Engineering Commons^™

Open-Ended Hollow Coaxial Cable Resonance Sensing Via Permittivity Fluctuations For Applications To Exhaled Breath Health Monitoring, Peter Henry Holtmann

Masters Theses

"We report a pre-diagnostics breath analyzer based on the open-ended hollow coaxial cable resonator (OE-HCCR) to achieve real-time differentiation of healthy and compromised lung function through electromagnetic analysis of exhaled breath matter. A two-phase amplification scheme of electromagnetic signatures metered via the S11 phase curve offers high sensitivity to permittivity fluctuations in exposed airflow. The mathematical model of the breath analyzer is explained, followed by experimental validation of numerical findings from previous work. The collection of breath transient signals is performed through monitoring the reflected power magnitude and phase of the scattering parameter (S11) at the resonance frequency. Material fluctuations …

Improved Decap Model And Placement Optimization Algorithm For Power Distribution Network Design, Jack Juang

Masters Theses

"Decoupling capacitors (decaps) are used in power distribution network (PDN) design to act as a low impedance return path for noise and act as a local source of charge when required by integrated circuits (IC). For placement of decaps, which can number even to the hundreds, many algorithms have been proposed including genetic algorithms (GA), iterative algorithm, and machine learning methods.

One limitation of iterative decap placement algorithms (adding one decap at a time) is how the construction of the algorithm affects the form of the final solution. For example, if the reward function (used in GA and machine learning …

A Real-Time Microwave Camera Using Zero-Bias Diode Detector, Liang Liu

Masters Theses

"This thesis presents the design of a microwave camera that utilizes a two-dimensional array of elliptical slot antennas and diode detectors to quickly and accurately locate radiation sources. Unlike traditional scanning techniques like ESM and holography, which rely on mechanical scanning, require a long measurement time, and are prone to mechanical errors, the microwave camera operates quickly and efficiently by using electronic switching to access the output of each detector. This results in a more precise and efficient means of locating radiation sources'--Abstract, p. iii

Static I-V Curve And Aging Test For Pim Characterization In Metallic Contacts, Kalkidan Anjajo

Masters Theses

"Spring clips and fabric-over-foams (FOFs) are widely used in mobile devices for electrical connection purposes. However, the imperfect metallic connections tend to induce passive intermodulation (PIM), resulting in a receiver sensitivity degradation, known as RF desensitization. Due to the complexity of the PIM characterization, there is not yet a way to evaluate PIM performance using a simple setup for environments like factories. In this study, a current-voltage (I-V) behavior-based PIM evaluation method is proposed and validated with various metallic contacts and contact forces. The test results demonstrated the feasibility of the PIM performance evaluation based on the measured static I-V …

Prediction And Root-Cause Analysis For Smart Speaker Intentional Electromagnetic Interference Attacks, Tanner Fokkens

Masters Theses

"Smart home and Internet of Things (IoT) devices have become ubiquitous in homes over the past decade. The smart speaker itself is often the device that interfaces all these devices together. Because of this, the smart speaker can become a point of attack for someone trying to exploit or hack into the smart home devices. In the past few years, it was discovered that smart speakers with microwave electromechanical system (MEMS) microphones are susceptible to intentional electromagnetic interference (I-EMI) attacks by modulating an audio command to a high-frequency carrier signal. This attack allows for command recognition for long-distances and smart …

Numerical Investigations Of 2-D Magnetic Nozzles On Pulsed Plasma Plumes, Joshua Daniel Burch

Masters Theses

"This research presents studies of a novel type of magnetic nozzle that allows for three-dimensional (3-D) steering of a plasma plume. Numerical simulations were performed using Tech-X's USim® software to quantify the nozzle's capabilities. A2-D planar magnetic nozzle was applied to plumes of a nominal pulsed inductive plasma (PIP) source with discharge parameters similar to those of Missouri S&T's Missouri Plasmoid Experiment (MPX). Argon and xenon plumes were considered. Simulations were verified and validated through a mesh convergence study as well as comparison with available experimental data. Periodicity was achieved over the simulation run time and phase angle samples were …

Automatic Sparse Esm Scan Using Gaussian Process Regression, Jiangshuai Li

Masters Theses

“Emission source microscopy (ESM) technique can be utilized for localization of electromagnetic interference sources in complex and large systems. In this work a Gaussian process regression (GPR) method is applied in real-time to select sampling points for the sparse ESM imaging using a motorized scanner. The Gaussian process regression is used to estimate the complex amplitude of the scanned field and its uncertainty allowing to select the most relevant areas for scanning. Compared with the randomly selected samples the proposed method allows to reduce the number of samples needed to achieve a certain dynamic range of the image, reducing the …

Optimization And Modeling Of Esd Protection Devices, Li Shen

Masters Theses

“Transient voltage suppressors (TVS) are used to protect ICs (integrated circuits) against overvoltage, ESD (Electrostatic Discharge), inductive load switching, and even lightning strikes. In this research, a transient behavior model framework for ESD protection devices is used for modelling four different types of TVS (non-snapback, snapback, spark gap like device and varistor). The System-Efficient ESD Design (SEED) methodology is utilized to strengthen the trust in the model framework by efficient simulation of ESD interaction of the off-chip ESD protection devices with the IC ESD protection device and associated measurement data.

Improvements in the TVS transient response, accounting for conductivity modulation, …

State Level Trends In Renewable Energy Procurement Via Solar Installation Versus Green Electricity, Eric Michael Hanson

Masters Theses

“In the past 5 years, consumer options for procuring renewable energy have increased, ranging from rooftop solar installation to utility green pricing to Community Choice Aggregation. These options vary in terms of costs and benefits to the consumer as well as grid integration implications. However, little is known regarding how the presence of a wide range of options for utility-scale renewable procurement affects demand for distributed residential solar installations. In theory, there are three possible relationships, (1) positive correlation, where utility-scale and distributed resources complement each other to increase overall production, (2) negative correlation, where utility-scale and distributed resources are …

Analysis Of Electromagnetic Interference Problems Causedbyhigh-Speed Multiplayer Boards With Split Referenceplane, Xin Fang

Masters Theses

"Digital/Analog ground partitioning has been used to isolate noisy digital and power current from sensitive analog currents in high-speed multiplayer printed circuit boards. The through-hole signal via enables convenient routing and component placement on the PCB and is used for signal interconnections when the signal traces are changing the layers. This design, however, breaks the current return path for signal traces that cross the two separated grounds, which causes undesired effects such as signal distortion and radiated emission.

Electromagnetic mechanism associated with them needs to be understood to control and suppress these undesired effects. In this paper, we have investigated …

Predicting Radiated Emissions From A Cable Harness Through Component Level Tests, Fuwei Ma

Masters Theses

“In this work, a procedure is developed to predict the radiated emissions from a cable harness using component-level tests. Direct measurement on the engine control unit is utilized to accurately characterize the equivalent common mode source voltages and impedance associated with the device. The cable harness geometry is reduced using the equivalent cable bundle approach by lumping wires according to the source and load impedance compared with characteristic impedance of the harness, which dramatically reduces the measurement effort and allows practical 3D full-wave simulation of the radiated emissions. Radiated emissions are predicted from an engine control unit (ECU) and an …

Method Of Optimal Battery Scheduling With Optimal Battery And Photovoltaic Sizing, Gideon Hallman

Masters Theses

“Renewable energy generation is on the rise. One of the best ways to capitalize on this intermittent power supply is by using the renewable energy source in tandem with batteries. A joint photovoltaic (PV) and battery system model was created that implemented battery degradation and optimized battery usage using a Markov Decision Process (MDP). This system was then subjected to a series of tests to do a sensitivity analysis while optimizing the battery and PV sizing for the system at hand. Parametric sweeps of solar power and battery capital costs, the cost of energy taken from the grid, the cost …

A Physics-Based Pi Pre-Layout Tool For Pcb Pdn Design, Shuang Liang

Masters Theses

"With increasingly stringent requirements for lower voltage supply, and higher density in PCB PDN design, now integrity (PI) is an increasingly important aspect that must be considered. A pre-layout tool based on the Cavity Model and Boundary Element Method is built to automatically achieve a specified target impedance for a multi-layered Printed Circuit Board (PCB) Power Distribution Network (PDN) design with a minimal number of decoupling capacitors.

The pre-work about the post-layout design and analysis is proposed and the guidelines for creating a decoupling capacitors network with better performance has been built. With limit inputs, physical limitations for the minimal …

Design And Evaluation Of The 3d Printed Electromagnetic Absorber Built With Conductive Carbon-Filled Filament, Rui Mi

Masters Theses

"This research presents an application of the resistive frequency selective surface (FSS) fabricated with a 3D printed conductive material as an electromagnetic absorber for the EMI-reducing door. This solution allows to reduce radiated emissions of a router system. The resistive frequency selective surface has a three-layer structure. The top layer is a 3D printed FSS pattern, the middle layer is an air gap, and the bottom layer is a metal plane.

The first paper presents the methodology for manufacturing a frequency selective surface using the 3D printing technology, including the material characterization, design, fabrication, and evaluation.

The unpublished content presents …

Analysis And Design Of Dc-Link Capacitor In Cascaded H-Bridge Multilevel Active Front-End Converter, Muhammad Shehroz Malik

Masters Theses

Medium-voltage grid-tied systems often use a cascaded H-bridge multi-level active front-end. In this converter, dc link bus capacitors play an important role in stabilizing the converter and enabling both active and reactive power injections. The present work provides analytical expressions for the capacitor current, which are essential for optimizing system design (especially capacitor size vs. lifetime). Then, the expression is incorporated into the grid connected bidirectional power system model. Consequently, this work contributes to the guiding principles to choose accurate dc link capacitor ratings against grid-side power delivery requirements.

DC-link capacitors come with an expiration date which is dependent on …

The Field Coupling Mechanism Study For Near Field Probe, Shun Liu

Masters Theses

"In this part, the radius of the loop is used to predict the voltage induced by the E- field in the circular loop antenna. The thin rectangle loop and thick rectangle loop have been investigated. The equivalent radius of the rectangle loop is estimated by the average of the one over the distance between the points on the loop to the center of the loop. The estimation matches with the numerical simulation"--Abstract, page iv.

A Simple Background Elimination Method For Miniaturized Fiber-Optic Raman Probe, Bohong Zhang

Masters Theses

"Raman scattering is called a photonic - molecular interaction based on the kinetic model of the analytic. Due to the uniqueness of the Raman scattering technique, it can provide a unique fingerprint signal for molecular recognition. However, a serious challenge often encountered in Raman measurement comes from the requirements of fast, real-time remote sensing, background fluorescence suppression, and micro-environmental detection.

A new Miniaturized Fiber-Optic Raman Probe (MFORP) for Raman spectroscopy, used especially for eliminating background fluorescence and enhancing sampling, is presented. Its main purpose is to provide an overview of excellent research on the detection of very small substances and …

Seed Modeling Of An Esd Gun Discharge To A Usb Cable, Yang Xu

Masters Theses

“An IC protected by a transient voltage suppression (TVS) diode may fail if the TVS device does not turn on or does not turn on quickly enough, causing the IC to take the full brunt of the electrostatic discharge (ESD) event. Transient simulation models have been developed for ESD protection devices for the purpose of system-efficient ESD design (SEED). The TVS modeling methodology has been improved to better represent the physics that occurs during the TVS response and more accurately predict the interactions between off-chip and on-chip protection devices. Moreover, a complicated test scenario -- an ESD gun discharge through …

A Compact Wavelength Meter Using A Multimode Fiber, Ogbole Collins Inalegwu

Masters Theses

“Wavelength meters are very important for precision measurements of both pulses and continuous-wave optical sources. Conventional wavelength meters employ gratings, prisms, interferometers, and other wavelength-sensitive materials in their design. Here, we report a simple and compact wavelength meter based on a section of multimode fiber and a camera. The concept is to correlate the multimodal interference pattern (i.e., speckle pattern) at the end-face of a multimode fiber with the wavelength of the input lightsource. Through a series of experiments, specklegrams from the end face of a multimode fiber as captured by a charge-coupled device (CCD) camera were recorded; the images …

Bond Graph Modeling Of Critical Infrastructures For Cyber-Physical Security Implementation, Michele Jane White

Masters Theses

“In developed societies, there exists infrastructure vital to everyday life. This includes water and power systems. Technology is quickly evolving and being implemented on these utilities. This technology can range from smart metering in neighborhoods to volume sensors in local waste water treatment facilities. When networking, sensing, monitoring, or control devices are integrated with infrastructure it is considered a cyber physical system, or CPS. When information about an important physical system is connected to the virtual world, it is opened up to security risks. Cyber security can be provided to the CPS by monitoring the physical state of the system …

Physics-Based Modeling Of Lithium-Ion Batteries For Control And Estimation Applications, Brody J. C. Riemann

Masters Theses

“Lithium-ion batteries are extensively used in many application areas like consumer electronics, electric vehicles, and microgrids. As the world moves towards further electrification of vehicles and more widespread use of renewable energy sources, the need for large-scale battery storage systems will grow. To effectively replace conventional methods, batteries will need to be charged quickly while accounting for degradation to maximize lifetime. Further, larger batteries require more detailed safety monitoring, which is implemented using a battery management system (BMS). A BMS is responsible for state of charge (SOC) estimation, state of health (SOH) estimation, cell balancing, regulating voltage and current according …

Transfer Function Measurement For Automotive Intentional Emi And Thermal Runaway Investigation Of Lithium-Ion Battery By Intentional Emi, Woncheol Song

Masters Theses

"With an increasing demand for electric vehicles and autonomous driving, many components of a vehicle are being replaced as electric components. This implicates the possibility of an increase in the malfunction of electric components due to unknown electromagnetic interferences. In this reason, malicious intentional electromagnetic interference (IEMI) is being considered as a growing threat for the current and next generation of automotive technology.

In the first topic, the transfer function between the IEMI attacker and the engine control unit (ECU) circuit in an automobile is extracted to analyze how the IEMI affects the vehicle.

In the second topic, to mimic …

Modeling And Control Of Cascaded Bridgeless Multilevel Rectifier Under Unbalanced Load Conditions, Sai Hemanth Kankanala

Masters Theses

“The goal of this project is to model and control a novel unidirectional cascaded multilevel bridgeless rectifier as an active front end in medium and high voltage applications. This topology has many advantages over a conventional cascaded H-bridge rectifier, such as lower implementation cost, higher reliability, and greater flexibility with similar power quality. The complete design process of the proposed converter is developed step by step in order to meet all the desired objectives. The steady-state mathematical model is used to develop a method for the voltage balancing of dc cells. Power factor analysis is discussed to mathematically derive requirements …

Design And Development Of Power Processing Units For Applications In Electrically-Propelled Satellite Systems, Kartikeya Jayadurga Prasad Veeramraju

Masters Theses

"Electrospray technology provides a way to ionize specialized liquids by applying high voltages across a sharp porous tip and a metallic mesh. This technology is widely used in the field of mass spectroscopy for generating ions for testing purposes. The dawn of nano-satellites posed new challenges in the miniaturization of many conventional satellite sub-systems. One significant challenge faced in such a process was the miniaturization of the propulsion system. Electrosprays have started to find their application in the field of Aerospace Engineering and now are formally known as Electrospray Thrusters. These thrusters provide high specific impulse and are attractive substitutes …

Serdes Channel Crosstalk Mitigation Methodology With Industrial Implementation Guidance, Junda Wang

Masters Theses

"With the increasing data rate of digital circuits, the differential crosstalk degrades the signal integrity performance in PCBs drastically. Usually, in the trace area, crosstalk can be isolated by stitching vias and adding shielding ground vias can also shield coupling in the ball gate array (BGA) and pin field area. The traditional way to mitigation crosstalk in the BGA and pin field area through adding more ground vias between signal pairs or increasing the spacing in between, it demonstrated us the efficiency on crosstalk cancellation efficiency but it also increases the size of products and it would be contradictory to …

Design And Comparison Of Unoptimized And Optimized Gray Code Multi-Level Systems, Shirly Adams Gamliel

Masters Theses

“As the conventional binary MOS-based VLSI technology is reaching limitations in chip area, speed, and power, new technologies are being researched. Some such technologies relate to multi-level logic design. This thesis explores the process and benefits of applying and optimizing multi-level design techniques to an existing Gray code binary system. Specifically, the multi-level system is designed using CoreMem technology and is optimized using Indira Dugganapally’s optimization techniques.

The first step is generating the n-bit binary and quaternary truth tables for an encoder’s Gray code output and additional desired data. Then, the data for each n-bit system is arranged in multi-level …

Estimating Electromagnetic Emissions From A Site Installation With Multiple Racks Of Server Equipment, Ze Sun

Masters Theses

“There are hundreds, sometimes even thousands, of servers working simultaneously inside a data center. Their radiation can be a problem and cause EMI issues. However, it is not feasible to perform full-wave simulation of these racks because of the large electric size of the model. In this thesis, an algorithm is proposed to predict the emission form rack array. The equivalent dipole source is extracted from EMI measurement data of a single rack and used as the radiation source in the multiple rack model. The coupling between racks cannot be ignored, but through the simulation, it is also found that …

Unified Probe Launch Pattern Design And Methodology Of Differential Probe Characterization, Han Deng

Masters Theses

"Differential probe is wildly used in the signal integrity area to do the accuracy signal measurement in frequency domain or time domain. Comparing with traditional SMA connector measurement, the probe measurement has several advantages such as the high flexibility and measurement efficiency. Nevertheless, the probe has some disadvantages such as multiple design patterns and the difficulty of fast landing. In this thesis, a unified probe landing pattern is provided to solve the con of probes and a probe testing fixture is designed for characterize probe and extract the probe model.

In the first portion, a unified differential probe launching pattern …

Modeling Impact Of Glass Weave On Differential Phase Skew By Design Of Experiments Method, Feng Zhang

Masters Theses

"The glass weave structure of a manufactured Printed Circuit Board (PCB) is scanned under a Scanning Electron Microscope (SEM), with top-down and cross-sectional views. Previously, analytical methods were used to investigate the glass-weave effect on transition properties in a PCB. Based on the SEM observation, this study was conducted to build full-wave models using various glass-weave types and different relative positions between differential traces and glass-weave bundles. This study aims to obtain the relationship between the glass weave and trace geometry, and the phase skew of the differential trace by using Design of Experiment (DoE) method and simulation results"--Abstract, page …

Experimental Characterization Of Common-Mode Sources For Prediction Of System Level Common-Mode Current On Cable Harnesses, Sameer Sudha Arun Walunj

Masters Theses

"Common-mode current on cable harnesses is often the primary source of radiated emissions below several hundred megahertz. It is difficult, however, to estimate common-mode currents that will occur in a system from component level tests because the common-mode impedances are different in the system. Research presents two methods for using simple component level tests to estimate equivalent common-mode source voltages and source impedances responsible for generating common-mode current. Key to these methods is assuming the harness can be represented with two transmission lines, one terminated with a short and one with an open. Equivalent sources are predicted for those circuits …