Electrical and Computer Engineering Commons^™

Fabrication Of Horizontal Silicon Nanowires Using A Thin Aluminum Film As A Catalyst, Khaja Hafeezuddin Mohammed

Graduate Theses and Dissertations

Silicon nanowires have been the topic of research in recent years for their significant attention from the electronics industry to grow even smaller electronic devices. The semiconductor industry is built on silicon. Silicon nanowires can be the building blocks for future nanoelectronic devices. Various techniques have also been reported in fabricating the silicon nanowires. But most of the techniques reported, grow vertical silicon nanowires. In the semiconductor industry, integrated circuits are designed and fabricated in a horizontal architecture i.e. the device layout is flat compared to the substrate. When vertical silicon nanowires are introduced in the semiconductor industry, a whole …

Photodetectors And Photovoltaic Devices Based On Semiconductor Nanomaterials, Jiang Wu

Graduate Theses and Dissertations

Photodetectors based various nanostructures and plasmon enhanced solar cells are investigated in this dissertation. The motivation of the dissertation rise is driven by urgent need of both high efficiency photodetectors and solar cells.

First, quantum dot infrared photodetectors have been intensely investigated due to their promise in high performance photodetectors. However, the strain-driven growth of quantum dots has hindered the progress of quantum dot photodetectors. The presence of strain in the device presents complexity in designing as well as defects. Therefore, in this project, new designs of quantum dot photodetector structures are presented to improve the control over detection wavelength. …

Optical And Magnetic Properties Of Feni Slanted Columnar Thin Films Infiltrated With Pmma And Fe3O4 Nanoparticles, Dan Liang

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

In this thesis, dielectric polymer and magnetic nanoparticles were utilized to hybridize FeNi Slanted columnar thin films (SCTFs). Firstly Fe₃O₄ in PMMA matrix was prepared by physical blending process. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) were used to investigate the dispersion of the nanoparticles in PMMA matrix and the preparation conditions were varied to optimize the dispersion. The hybridized materials were prepared by the infiltration of PMMA and 5 wt% Fe₃O₄ nanoparticles/PMMA to the voids of FeNi SCTFs. Spin-coating and annealing process were employed to reach an excellent infiltration.

The structural …

In-Situ Ellipsometry Characterization Of Anodically Grown Silicon Dioxide And Lithium Intercalation Into Silicon, Eric A. Montgomery

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

In this thesis, in-situ ellipsometry and electroanalytical investigations of two electrochemical processes are reported: including the formation of anodically grown silicon dioxide and the intercalation of lithium into silicon. Analysis of the ellipsometry data shows that the anodically grown silicon dioxide layer is uniform and has similar properties as thermally grown silicon dioxide. The lithium-ion intercalation data reveals non-uniform thin film formation, which requires further studies and development of appropriate ellipsometric optical models.

Advisers: Eva Schubert and Mathias Schubert

Dynamic Modeling And Characteristic Analysis Of Proton Exchange Membrane Fuel Cell, Qiu-Hong Jia, Ming Han, Bin Deng, Cai-Zhi Zhang

Journal of Electrochemistry

In this paper, a dynamic model of PEMFC is developed to estimate the dynamic performance of PEMFC by analyzing in detail the influence factors of voltage of PEMFC including various losses. The partial pressure of hydrogen and oxygen is obtained using the differential form of the ideal-gas equation in this model. The steady-state model is obtained by setting reasonable parameter values. The simulation results and experimental results have good consistency, which shows that the simulation model is correct, reasonable and effective. It analyzed the dynamic response characteristics of the output voltage and the partial pressure of hydrogen in condition of …

Microemulsion Preparation And Electrochemical Characterization Of Pt/C，Ptir/C Electrocatalysts, Ya-Ping Zeng, Sheng Sui

Journal of Electrochemistry

The Pt/C electrocatalysts were prepared by three different systems and the PtIr/C electrocatalysts were prepared with four different Ir contents. The samples were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), cyclic voltammetry (CV), potentiostatic and potentiodynamic polarizations measurements. The experimental results confirmed that the electrocatalyst particles prepared by the microemulsion method were well distributed on XC-72R supports with the active particle sizes of 5～10nm and good electrocatalysts activity. The Pt85Ir15/C electrocatalysts showed the highest overall electrochemical activity in unitized regenerative fuel cell.

Preparation And Characterization Of The Lani0.6fe0.4o3-Δ Cathode For Intermediate Temperature Solid Oxide Fuel Cell, Hang Liu, Bo Huang, Xin-Jian Zhu

Journal of Electrochemistry

The LaNi0.6Fe0.4O3-δ as cathode material for intermediate temperature solid oxide fuel cell was prepared using a combustion synthesis technique. The X-ray diffraction (XRD) pattern showed that the single-phase LaNi0.6Fe0.4O3-δ perovskite could be obtained after heat treatment at 600°C. The TEM and SEM images of the synthesized powders revealed that the grains were 50-100nm. According to the electrochemical impedance spectra (EIS), the polarization resistance of the symmetric cell LaNi0.6Fe0.4O3-δ/ScSZ/LaNi0.6Fe0.4O3-δ sintered at 1050°C was the smallest (0.70Ω?cm2, 0.27Ω?cm2 and 0.12Ω?cm2 at 750°C, 800°C and 850°C, respectively). In the presence of the Fe-Cr alloy interconnection at 750°C, the cathode performance showed that, with …

The Electrochemical Properties Of Cathode Materials Limxv3-Xo8, Hui Yang, Gang-Gang Zhao, Juan Li

Journal of Electrochemistry

The cathode material of LiMxV3-xO8 was fabricated by sol-gel method using citric acid as a chelating agent and doping transition metal ions M (Mn, Ti, Co and Ni). The structure, morphology and electrochemical proprieties of the LiMxV3-xO8 samples were investigated by XRD, TGA/DTA, SEM, charge-discharge and CV measurements. The results showed that different calcining temperatures result in different structures and morphologies, which lead to different discharge capacities. The specific discharge capacity of the sample calcined at 500℃ for 6 h was up to 300.4 mAh/g in the first cycle, and the capacity decreased with the increasing of calcining temperature. The …

Indirect Electrochemical Reduction And Cotton Dyeing Process In Fe(Ⅲ)-Oxalate-Calcium Gluconate System, Qing-Zhi Wang, Wei Wang

Journal of Electrochemistry

The electrochemical behavior and possible reaction mechanism in Fe(Ⅲ)-oxalate-calcium gluconate system were studied by cyclic voltammetry. The results showed that Fe(Ⅱ)-gluconate was the final reductant. The reduction time, the working voltage and the cathode area influenced the current efficiency. The high current efficiency of 89% for the indirect electrochemical reduction of Vat Scarlet R could be achieved with reduction time of 10 min, working voltage of 4 V and cathode area of 40 cm2 in Fe(Ⅲ)-oxalate-calcium gluconate system.

Preparation And Application Of Nano-Nio As Anode In Lithium-Ion Batteries, Cheng-Dong Bai, Jia-Jia Chen, Qi Zhang, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

In this work, the nano-NiO material was prepared by hydrothermal method. The surface morphologies and electrochemical properties of nano-NiO material were investigated. The special nano-NiO material with porous surface assembling honeycombs(100-200nm) was obtained by using surface active agents. The discharge capacity of nano-NiO electrode up to 2385.7 mAh/g was achieved at current density of 0.1A/g in the first circle,while 1100mAh/g could be maintained after 100 circles. At current density of 2.0A/g, the discharge capacity of 600 mAh/g was obtained. And when the current density was reduced to 0.1A/g, the discharge capacity was restored to 1050 mAh/g. The nano-NiO electrode exhibited …

A Brief Review Of Research Progress In The Development Of Engineering Models For Lithium Ion Batteries, Da-Wei Wang, Dong-Jiang Li, Jun Li, Yong Yang

Journal of Electrochemistry

Lithium ion battery has become an important and popular electrochemical device for energy storage.Suitable evaluation and understanding of electrochemical performance and state of charge play a key role in the applications of lithium ion batteries.Construction and utilization of engineering modeling for lithium ion batteries is an effective way to fulfill this target.In this paper,engineering models of lithium ion batteries based on electrochemical reaction,ionic diffusion and migration are introduced.The emphasis is placed on the development of engineering models by the introduction of side reaction,phase transition,stress and energy.The applications of engineering models in such simulations as charge-discharge,concentration distribution,current distribution,state of charge,stress and …

Electrocatalytic Determination Of 15 Kinds Of Phenolic Compounds By Novel Gold Nanoparticles-Modified Glassy Carbon Electrode, Yan-Ping Cui, Wei-Xing Wang, Chang-Zhu Yang, Wen-Hong Pu

Journal of Electrochemistry

A gold nanoparticles modified glassy carbon electrode (Au/GCE) was used to detect 15 kinds of phenolic compounds. In the cyclic voltammetry measurements, the peak currents of phenolic compounds at Au/GCE were all increased as compared with GCE and planar gold electrodes, and the oxidation potentials were determined by the activity of analytes. Besides, electrocatalysis of salicylic acid was studied at Au/GCE. The results showed that, there was a good linear relationship between the oxidation current and the concentration of salicylic acid, and the current sensitivity was 1.8 fold higher than that obtained on GCE. Trace phenolic compounds determination could be …

Electrochemical Properties Of Tungstogermanate And Electrocatalysis Of H2o2 On Gew11co/P-Opd/Gc Electrode, Li-Li Zhu, Jian-Ying Qu, Jue Wang, Hao-Yue Feng

Journal of Electrochemistry

The electrochemical properties of Co-substituted trimeric tungstogermanate containing Keggin fragments were studied. Cyclic voltammograms revealed two couples of reversible redox peaks on glassy carbon (GC) electrode in acid solutions. They corresponded to two-electron reductions accompanying by the additions of four protons and three protons, respectively, both were controlled by adsorption. The differences in the peak potentials of 2-electron-4-proton and 2-electron-3-proton reactions were 31 mV and 35 mV, respectively..Furthermore, the tungstogermanate (GeW11Co) modified GC electrode with functionalization by poly(o-phenylenediamine) (P-oPD) was prepared readily by electropolymerization. The GeW11Co/P-oPD/GC electrode could electrocatalyze the reduction of hydrogen peroxide, which showed good stability and quick …

Preparation And Characterization Of Casno3 Anode Material For Lithium Ion Batteries, Ran Sun, Zi-Geng Liu, Ya-Qi Jiang

Journal of Electrochemistry

In this study the precursor CaSn(OH)6 was prepared via a hydrothermal process, and its composition, surface feature and phase-transition were characterized by XRD, SEM and DSC-TGA. The shapes of CaSn(OH)6 crystals were effectively controlled by adjusting the volumn ratio of H2O and CH3CH2OH solvents. Perovskite CaSnO3 could be obtained by calcination of CaSn(OH)6 at 800 ℃. The reversible capacity of 334.4 mAh/g with good cycling stability could be achieved with the CaSnO3 electrode.

Preparation And Capacitance Characteristics Of Nickel Oxide Electrode With Mesh-Like Structure, Hui Xu, Zhen-Jun Peng, Dong-Hong Guo, Jun-Ling Li

Journal of Electrochemistry

The mesh-like structure of NiO electrode was obtained by first preparing the precursors via hydrothermal process using nickel sulfate and carbamide as reactants, sodium hexametaphosphate as a surfactant, and followed by calcination of the precursors at 400 ℃. The structure, morphology and capacitance characteristics of NiO electrode were characterized by XRD, SEM and constant current charge-discharge testing techniques. The effects of hydrothermal temperatures on the electrochemical properties of NiO electrode were investigated. The results showed that the better property of nickel oxide was obtained when the mole ratio of nickel to urea was 1:4 and the hydrothermal temperature was 140℃. …

Thermodynamic Limit To Photonic-Plasmonic Light-Trapping In Thin Films On Metals, Eric A. Schiff

Physics - All Scholarship

We calculate the maximum optical absorptance enhancements in thin semiconductor films on metals due to structures that diffuse light and couple it to surface plasmon polaritons. The calculations can be used to estimate plasmonic effects on light-trapping in solar cells. The calculations are based on the statistical distribution of energy in the electromagnetic modes of the structure, which include surface plasmon polariton modes at the metal interface as well as the trapped waveguide modes in the film. The enhancement has the form 4n²+nλ/h (n – film refractive index, λ – optical wavelength, h …

Optimation Of Nitrogen And Phosphorus In Azolla Growth As Biofertilizer, Hany Handajani

Makara Journal of Technology

Nitrogen is one of the most important minerals for living organisms. Azolla is known as a small water fern which can fix nitrogen through the symbiotic association with the blue green algae Anabaena. Experimental studies were carried out in the glass house, investigating the growth of Azolla using different levels of nitrogen and phosphorus in the media. The experiment used 12 treatments with 3 levels of nitrogen (0, 5, and 10 mg atom/L) and 4 levels of phosphorus (0, 10, 20, and 30 mg atom/l) in a factorial design with 3 replicates. The results show that the highest biomass for …

Establishment Code Hand Palm (Palm Code) 2d Gabor-Based Method, I Ketut Gede Darma Putra, Wira Bhuana, Erdiawan Erdiawan

Makara Journal of Technology

Establishment Code Hand Palm (Palm Code) 2D Gabor-Based Method. Palmprint is relatively new in physiological biometrics. Palmprint ROI segmentation and feature extraction are two important issues in palm print recognition. This paper introduces two steps in the center of mass moment method for ROI segmentation that will be applied in the Gabor 2D filter to obtain palm code as palmprint feature vector. Normalized Hamming distance was used to measure the similarity degrees of two feature vectors of palmprint. The system was tested using database 1000 palmprint images generated from 5 samples from each of the 200 persons randomly selected with …

The Effectiveness Of Anaerobic Baffled Reactor And Rotating Biological Contactor In Batik Wastewater Treatment, Augustinus Ignatius Kristijanto, Widhi Handayani, Purwanti Asih Anna Levi

Makara Journal of Technology

Batik is one of popular arts of Indonesia. The batik industries in Sragen, Central Java, are prepared to compete in global market. In order to realize that objective, batik products should fulfill some qualifications, one of which is “environmental friendliness”. As batik production is usually generating wastewater which pollutes the environment, the technology of wastewater treatment should be developed to solve the problem. This preliminary study has been done to assess the effectiveness of anaerobic baffled reactor (ABR) and rotating biological contactor (RBC) in batik wastewater treatment. In 40 days of treatment period, the ABR performance in reducing pollutants showed …

Antibacterial Activity Of Papaya Leaf Extracts Against Pathogenic Bacteria, Elisa Friska Romasi, Jessica Karina, Adolf Jan Nexson Parhusip

Makara Journal of Technology

It was reported that the extracts of papaya leaves could inhibit the growth of Rhizopus stolonifer. Antibacterial activity of Carica papaya leaf extracts on pathogenic bacteria was observed in this study. Papaya leaves were extracted by using maceration method and three kinds of solvents: ethanol, ethyl acetate, and hexane. Papaya leaf extracts were tested against Bacillus stearothermophilus, Listeria monocytogenes, Pseudomonas sp., and Escherichia coli by agar diffusion method. The objectives of this study were to determine extract ability against pathogenic bacteria, to observe the influence of pH, NaCl, and heat on extracts ability, and to observe extract ability against B. …

Analytical And Computational Simulation Approaches To Design Low Energy Glass Block, Floriberta Binarti, Agustinus Djoko Istiadji, Prasasto Satwiko, Priyo Tri Iswanto

Makara Journal of Technology

Analytical and Computational Simulation Approaches to Design Low Energy Glass Block. An environmentally friendly process was developed to produce a low embodied energy glass block from waste glasses. The energy efficiency of the glass block is represented by its thermal conductance (U) <3.177 W/m2.K and solar transmittance (SHGC) ≤0.25 as well as visible light transmission (VT) ≥0.27. A cavity was applied to reduce U value while insignificantly reducing VT. Analytical method was used to calculate the U value of glass blocks, ignoring the effect of convection. Ecotect program was used to analyze light level (VT) and heat load (SHGC) of each model. Effect of convection was simulated using a CFD program, which showed air velocity inside the cavity and temperature gradient in glass blocks. Comparing to an application with 3 mm float glass, energy efficiency obtained through applying the glass blocks could reach 96%. This simulation study ignored the presence of adhesive among glass layers that potentially reduces the VT and the SHGC of the glass blocks.

Flexible Connection Elastomeric Rubber As A Pounding Resisting Element Between Two Adjacent Buildings, Yuskar Lase, James Jatmiko Oetomo

Makara Journal of Technology

Flexible Connection Elastomeric Rubber as a Pounding Resisting Element between Two Adjacent Buildings To solve pounding problem of two adjacent buildings, structural designer usually employs a dilatation between the structures or make the two structures as a monolith structure. Other alternative is by using an elastomeric rubber as a pounding resisting element between the two structures. Effectiveness in applying elastomeric rubber component as flexible connection of two adjacent structures is the main focus of this paper. Various simulations such as structure models, earthquake excitations and openings in gap element are studied. Observation of maximum structural responses will be performed for …

Effect Of Copper Addition On Mechanical Properties And Electrical Conductivity Of Pp/C-Cu Bipolar Plate Composites, Anne Zulfia, Taufik Abimanyu, Verina Warga Dalam

Makara Journal of Technology

Effect of Copper Addition on Mechanical Properties and Electrical Conductivity of PP/C-Cu Bipolar Plate Composites. Bipolar plate is a major component in PEM fuel cell which possess main function of collecting and removing electrons from anode to cathode. Therefore, materials for bipolar plates produced must have high electrical conductivity. To obtain bipolar plate materials which is cheap, lightweight and high conductivity, so it is developed bipolar plates material based on PP/C-Cu composite. PP/C-Cu composites has been made by mixing all materials then compounding, rheomix, hot blending and hot press. Cu (Copper) has been used various from 0.1 wt%, 1 wt% …

Medium Density Fibreboard Made Of Acetylated Sludge From Paper Mill, Luthfi Hakim, Evalina Herawati, I Nyoman Jaya Wistara

Makara Journal of Technology

Medium Density Fibreboard Made of Acetylated Sludge from Paper Mill. Research of using sludge as raw material for making medium density fibreboard (MDF) was useful to create additional value of sludge. The objective of the research was to evaluate physical properties, mechanical properties, and durability of MDF from acetylated sludge in 4 levels of acetate anhydride (0%, 3%, 5%, and 7%) with 3 replicates. The MDF was made using dry process. After materials were mixed with adhesives, they were pressed using hotpress under 170 oC temperature and 45 Pa pressure for 25 minutes. The size of the MDF sample was …

Application Of Empirical Orthogonal Function Models To Analyze Shoreline Change At Bangkalan Madura, Darius Arkwright, Suntoyo Suntoyo

Makara Journal of Technology

Bangkalan’s shoreline, especially on the opposite side of Surabaya, has been evaluated to determine the morphological changes due to wave attack, near-shore current, long-shore sediment transport and coastal configuration. This research aims to determine the dominant patterns of variation of Bangkalan’s shoreline change, expressed by Eigen-function in empirical orthogonal function (EOF) models. That was started with data collection such as oceanographic data (wave and tidal), bathymetry and topographic map and sediment data. All data was used for forecasting two-monthly shoreline. Coordinate of two-monthly shoreline was used as input of EOF model. The first Eigen mode is a profile of shoreline …

Alos/Palsar Image Processing Using Dinsar And Log Ratio For Flood Early Detection In Jakarta Based On Land Subsidences, Dodi Sudiana, Mia Rizkinia

Makara Journal of Technology

Flood that occurred in Jakarta is not only influenced by rainfall, urban planning system and drainage alone, but also may be involved land subsidence (LS). LS is possible in because Jakarta stands on top of layers of sediments and the presence of ground water consumption in very large quantities. In this research, the Advanced Land Observing Satellite (ALOS)/Phased Array type L-band Synthetic Aperture Radar (PALSAR) data was processed to determine the level of LS in Jakarta area and its relation to flood potential area. Differential interferometry method (DInSAR) was performed on two PALSAR data with different acquisition years, i.e. 2007 …

Flutter Analysis Of Rx-420 Balistic Rocket Fin Involving Rigid Body Modes Of Rocket Structures, Novi Andria

Makara Journal of Technology

Flutter Analysis of RX-420 Balistic Rocket Fin Involving Rigid Body Modes of Rocket Structures. Flutter is a phenomenon that has brought a catastrophic failure to the flight vehicle structure. In this experiment, flutter was analyzed for its symmetric and antisymmetric configuration to understand the effect of rocket rigid modes to the fin flutter characteristic. This research was also expected to find out the safety level of RX-420 structure design. The analysis was performed using half rocket model. Fin structure used in this research was a fin which has semispan 600 mm, thickness 12 mm, chord root 700 mm, chord tip …

Physical Characterization And Desulfurization Of Biobriquette Using Calcium-Based Adsorbent, Mahidin Mahidin, Asri Gani, Khairil Khairil

Makara Journal of Technology

Combustion of coal and co-combustion of their co-fuel contribute to gas emissions. Among the gas emissions are SOx, NOx, CO and CO2. Introduction of calcium based adsorbent is addressed to absorb SO2 that release to the atmosphere during the combustion process. Objective of the research is at first to observe the physical characteristics of biobriquettes as a function of briquette compositions (coal to palm kernel shell ratios) and Ca/S ratios (Ca in adsorbent and S in briquette) using a natural adsorbent (shellfish waste). The second objective is to investigate desulfurization characteristics as a function of Ca/S ratios and desulfurization temperatures …

Application Of Principal Component Proximity Transform And Geostatistics Methods For Volume Shale Distribution As Reservoir Characreristic Imaging In Seismic 3d, Nur Islami

Makara Journal of Technology

Application of Principal Component Proximity Transform and Geostatistics Methods for Volume Shale Distribution as Reservoir Characreristic Imaging in Seismic 3D. Principal component proximity transform (PCPT) technique was used to predict the content of volume shale into seismic data in reservoir modeling framework. The goal in this research is to get the volume shale imaging in three dimensions and allow for reservoir modelling. The reservoir modelling requires an integrated quantitative and qualitative data sources collected separately, such as well and seismic data. Integrating PCPT and Geostatistic methods can generate the detail information for characterization of reservoir’s properties. Finally, it shows that …

Improvement Of High Temperature Oxidation Of Low Carbon Steel Exposed To Ethanol Combustion Product At 700 °C By Hot-Dip Aluminizing Coating, Mohammad Badaruddin

Makara Journal of Technology

Low carbon steel (AISI 1005) was coated by hot-dipping into a molten Al-10% Si bath at 700 °C for 18s. After hotdipping treatment, the coating layers consisted of Al, Si, FeAl3, τ5-Fe2Al8Si, and Fe2Al5. The bare steel and the aluminized steel were isothermally oxidized at 700 °C in ethanol combustion product at atmospheric pressure for 49 h. The aluminized steel shows good performance in high temperature oxidation because the formation of Al2O3 layer on the coating surface. The growth of iron oxide nodules on the surface coating was accelerated by rapid outward diffusion of Fe-ions due to the presence of …