Computer Engineering Commons^™

Arduino-Based High-Frequency Signal Data Acquisition For Learning Media On Antenna And Wave Propagation Practices, Eko Marpanaji, Masduki Zakarijah, Nikko Aji Bayu Nugraha

Elinvo (Electronics, Informatics, and Vocational Education)

This paper discusses the research results on the development of learning media and the results of the feasibility test for the learning process. This study aims to: (1) obtain the design and prototype of Arduino-based high-frequency signal data acquisition learning media; (2) find out the level of feasibility of learning media that has been made for the learning process of Antenna Practice and Wave Propagation courses. The research model uses Research and Development with the ADDIE development method. The research stages in the ADDIE method are Analyze, Design, Develop, Implement, and Evaluate. The research began with the development of learning …

Cyberinet: Integrated Semi-Modular Sensors For The Computer-Augmented Clarinet, Matthew Bardin

LSU Doctoral Dissertations

The Cyberinet is a new Augmented instrument designed to easily and intuitively provide a method of computer-enhanced performance to the Clarinetist to allow for greater control and expressiveness in a performance. A performer utilizing the Cyberinet is able to seamlessly switch between a traditional performance setting and an augmented one. Towards this, the Cyberinet is a hardware replacement for a portion of a Clarinet containing a variety of sensors embedded within the unit. These sensors collect various real time data motion data of the performer and air fow within the instrument. Additional sensors can be connected to the Cyberinet to …

Pillow Based Sleep Tracking Device Using Raspberry Pi, Venkatachalam Seviappan

Electronic Theses, Projects, and Dissertations

Almost half of all people have sleep interruptions at some point in their lives, making sleep disorders a common issue that affects a sizeable section of the population. Both their physical and emotional well-being may suffer as a result of this.Insomnia, which is a prevalent sleep disorder, is identified by symptoms including insufficient sleep duration and quality, trouble initiating sleep, multiple nighttime awakenings, early morning awakenings, and non-restorative sleep. It is essential to employ sleep monitoring systems to detect sleeping disorders as soon as possible for prompt diagnosis and treatment. To avoid sleep related health issues, there are plenty of …

Assessing The Ability Of Arduino-Based Sensor Systems To Monitor Changes In Water Quality, Josiah Hacker

Honors College Theses

Access to safe water is vital to public health. While developed countries like the United States are recognized as having reliable and safe water, many small water utilities struggle with supplying consistent water quality. Technicians of these utilities will periodically test water samples from the influent and throughout the distribution system. However, this laborious and costly process does not capture sudden changes in influent water quality due to environmental conditions or pipes breaking in the distribution system. Here I show how an Arduino-based sensor can be used as a real-time, low-cost monitor of water quality parameters. Specifically, I developed a …

Phone Microwave, Khanh Kim Hoang, Emily Zhou

Computer Engineering

This project involves the installation of remote-control capabilities in an antique 1980s microwave, effectively turning the microwave into a “smart” device. While preserving the original functionality of the microwave, a combination of software and hardware components allows for remote microwave operations. The microwave can be remotely operated by calling the built-in number, and more advanced settings and options can be utilized by texting. The microwave is also secured against unauthorized use with the addition of a PIN code that is required to operate the device.

Barrier Knockdown Test Control System For The Cal Poly Kinesiology Department, Regina M. Chapuis

Computer Engineering

The goal of this project is to design and implement a new control system for the LEDs and buttons on an existing Barrier Knockdown setup in the Cal Poly Kinesiology department. The Barrier Knockdown test is a testing apparatus in which subjects knock down a series of mechanical barriers in one of three patterns. The computer system times their reaction and movement time, and the test as a whole provides students with data to study the phenomenon of Contextual Interference. This system was previously controlled by an old computer setup that ultimately crashed. This project recreates the logic and user …

The Music Bluetooth Controller: An Intersection Between Technology And Music, Lydia Wu

Senior Honors Theses

The modern musician faces a new challenge: how can technology be used to enhance a performance? This thesis documents the development of a Bluetooth remote controller that will aid today’s performing musicians by interacting with a digital display (e.g., an iPad) to flip musical score pages remotely. At its core, while mimicking a Bluetooth pedal (the current industry standard), this device attaches to the musician’s hand. In its pilot stages, the device has been referred to “MBC” (Music Bluetooth Controller).

Short Run Box Maker, Jesus Valdez-Ruelas

General Engineering

Small businesses with short run product catalogs have trouble finding the right size box that will work for multiple products. In turn, this leads most businesses to use oversized boxes resulting in unnecessary shipping fees. The objective of this project was to develop and test a cost-effective prototype of a box making machine that could create a short run of custom sized boxes. A Co2 laser was found to be the best option for cutting cardboard and a vertically standing machine was designed to feed the cardboard via rollers. To control cardboard movement stepper motors were used and controlled using …

Piezoelectric Energy Harvester Improvement, Nathan Embaugh, Jason Mack, Jeremiah Fitzgerald, Zachary J. Lindsey

Williams Honors College, Honors Research Projects

The energy harvester is used to convert a portion of the tire deflection waste energy to power up tire embedded sensors. A piezoelectric energy harvester is designed and some preliminary tests are done on it. So far, it has been shown that this design is sufficient for tire application. The team will need to modify the design of the energy harvester, the measurement setup and add a temperature and a strain senor to the existing setup so that the tire deflection and temperature can be measured and at the same time the energy harvester should be tested to see how …

Improving 3d Printed Prosthetics With Sensors And Motors, Rachel Zarin

Honors Projects

A 3D printed hand and arm prosthetic was created from the idea of adding bionic elements while keeping the cost low. It was designed based on existing models, desired functions, and materials available. A tilt sensor keeps the hand level, two motors move the wrist in two different directions, a limit switch signals the fingers to open and close, and another motor helps open and close the fingers. All sensors and motors were built on a circuit board, programmed using an Arduino, and powered by a battery. Other supporting materials include metal brackets, screws, guitar strings, elastic bands, small clamps, …

Smart Surge Irrigation Using Microcontroller Based Embedded Systems And Internet Of Things, Prashant Dinkar Borhade

Graduate Theses and Dissertations

Surge Irrigation is a type of furrow irrigation and one of many efficient irrigation techniques. It is one of the economical techniques and requires minimum labor for monitoring it. In surge irrigation, water is applied intermittently to a field to achieve uniform distribution of water along the furrows, which is important while irrigating, as it ensures that there is enough water near the root zone of the crop. The uneven distribution can cause a loss in crop productivity.

Surge irrigation uses a surge valve, which is an electro-mechanical device that irrigates a field. The commercial surge valves available on the …

Roborodentia Final Report, Trevor James Gesell, Zeph Colby Nord, Mitchell Tyler Myjak

Computer Engineering

The Senior Project consisted of competing in Roborodentia, a competition in which groups build robots to complete a particular task. This event took place at the Cal Poly Open House on Saturday, April 12th, 2018. For the competition, the robot was to collect Nerf balls from supply tubes raised approximately 7” from the board and shoot them into nets placed along the opposite side of the course. The design, manufacture, and testing of the robot began the first week of Cal Poly winter quarter and lasted until the day of the competition.

Senior Project - Roborodentia Robot, Nicholas Alexander Ilog

Computer Engineering

This project includes an autonomous robot capable of dispensing balls from a dispenser mounted on a wall and shooting the balls through targets five to eight feet away. The robot can hold up to five balls at a time and shoots balls one by one at targets.

Bicycle Power Meter, Andrew Mcguan

Computer Engineering

A power meter is a cycling training tool used to record the power a rider is outputting. This is very useful to athletes who regularly do bike workouts, because the power output is a consistent measure of the rider’s effort level, and is not affected by outside factors such as wind or road gradient. If a cyclist does a workout with the intent to carry a certain speed for a certain amount of time, a strong headwind will slow them down and make them work harder to maintain the same speed, defeating the goal of the workout. When a power …

Darling, Robot For Roborodentia 2018, Michael Le, Steven Liu

Computer Engineering

For our senior project, our group decided to build a robot to participate in Roborodentia 2018, an annual robotics competition overlooked by Professor Seng that takes place during open house. When taking into consideration the classes that Computer Engineering students had to have taken and the skills that we have developed throughout our time here on campus, a robotics project seemed to be an appropriate culmination of both the technical and non-technical skills that we have acquired.

Roborodentia Robot: Treadbot, Stephen C. Schmidt

Computer Science and Software Engineering

This document is a summary of my contest entry to the 2018 Cal Poly Roborodentia competition. It is meant to be a process overview and design outline of the mechanical, electrical, and software components of my robot.

Dynamic Routing And Network Monitoring For The Polywog Protocol, Ryan Lawrence, Josh Pfeffer

Computer Science and Software Engineering

This document analyzes the implementation of dynamic routing for router nodes in a mesh network. It examines the algorithm used to populate both the minimum-distance and the routing tables. Furthermore, it describes the node configurations used for testing and applications for mesh networks.

Additionally, this document describes the implementation and testing of network monitoring in a mesh network. It discusses the steps used to forward active nodes in the network between router nodes, a gateway node, and a network monitor.

Lastly, this paper details our future plans for implementing additional features for a network monitor.

Autonomous Speed Control For Kia Optima, Andrew J. Combs, Kyle Fugatt, Kevin Mcfall

The Kennesaw Journal of Undergraduate Research

The standard method for speed control is the cruise control system built into most modern vehicles. These systems employ a PID controller which actuates the accelerator thus, in turn, maintains the desired vehicle speed. The main drawback of such a system is that typically the cruise control will only engage above 25 mph. The goal of this paper is to describe a system which we used to control vehicle speed from a stop to any desired speed using an Arduino microcontroller and a CAN BUS shield, from where autonomous features can be built upon. With this system, we were able …

Farmbot Rfid Integration, Laura R. Swart

Computer Engineering

The purpose of this project is to assist the company FarmBot improve their product by adding RFID tracking to the FarmBot robot. RFID tracking will allow the robot to select and pick up tool heads without any user interference.

Smartfarm, Nathan A. Oto, Caleb Fink

Computer Engineering

The overall expectation of this product is to create an autonomous Arduino library that accurately and robustly collects plant environment data from the Smart Farm board. The Smart Farm PCB is split into two primary functions: Data Acquisition(DAQ) and Power Control. Each function of the PCB is controlled by an Atmega 328P Microcontroller. The primary concern for this report is the functionality of the DAQ microcontroller.

Wheelieking Trainer Project Report, Harold Hall Iii, Nathaniel Fox, Thomas Niemisto

Biomedical Engineering

In this report we will detail the design and implementation process of the WheelieKing Trainer project, a device that helps people learn how to do wheelies on a bicycle by preventing backward falls. Formal project requirements are specified, followed by the ideation and iteration process to meet those requirements. The components and methods used to create the device are described in detail. The results of the development process and usage test results of the device are included. Appendices at the end of this report include references, supporting analyses, and project management and timeline details.

Automation In Entertainment: Concept, Design, And Application, Ryan Thally

Undergraduate Honors Theses

The focus of this thesis is to explore the automation technology used in the modern entertainment industry. Upon completion of my thesis, I will deliver a working prototype of the chosen technology and present its capabilities in a choreographed show.

Implementation Of A Personal Area Network For Secure Routing In Manets By Using Low-Cost Hardware, Himadri Nath Saha, Rohit Singh, Debika Bhattacharyya, Pranab Kumar Banerjee

Turkish Journal of Electrical Engineering and Computer Sciences

Presently, mobile ad hoc networks (MANETs) are being used extensively in the defense, private, domestic, etc. fields and each of these emulates a personal area network (PAN). A MANET does not require any infrastructure; moreover, it can behave as a mobile network. These features have boosted the popularity of MANETs in the community. As more and more fields become dependent on MANETs, the system needs to be more energy aware and low cost. To commercialize MANETs, the routing protocols need to be lightweight, secure, and energy efficient, and the hardware on which it is to be implemented should be low …

Sistem Monitoring Pencemaran Polutan Kendaraan Via Gadget Berbasis Arduino, Adibatul Ardianto

Elinvo (Electronics, Informatics, and Vocational Education)

Sumber polusi udara salah satunya adalah gas buang kendaraan bermotor, gas yang dihasilkan dari pembakaran bahan bakar terjadi pada mesin kendaraan. Tingkat deteksi aplikasi dari sistem pembuangan kendaraan bermotor yang dibuat digunakan untuk mendeteksi jumlah kadar gas H_2, gas EtOH dan gas CO dengan menggunakan sensor TGS2201. Data dari sensor diolah oleh arduino dan hasilnya ditampilkan pada PC melalui port serial, desain program aplikasi dengan menggunakan Bahasa C.

Studying The Effects Of Serpentine Soil On Adapted And Non-Adapted Species Using Arduino Technology, Kiana Saniee, Edward Himelblau, Brian Paavo

STAR Program Research Presentations

Abstract: Serpentine soils are formed from ultramafic rocks and are represent an extreme environment for plants. Serpentine soils are unique in that they carry high concentrations of heavy metals, are nutrient deficient, particularly in calcium, and have poor water retention capabilities. Although these soils constitute harsh conditions for plant growth, there are a number of species that are adapted and even endemic to serpentine soil. Water retention by commercial potting mix was compared with serpentine soil. Also, serpentine adapted and non-adapted species were grown in both soil treatments and physiological data were collected. We used the Arduino electronic platform to …

Roborodentia 2016: Scorpion, Tyler Whalen

Computer Engineering

This report showcases my entry into the Roborodentia 2016 competition, and my senior project. I chose this project because robotics has always interested me, and this was a great opportunity to jump in headfirst.

I will step through my design decisions and detail all information necessary for replicating this build.

Stand, Lisa Yip

Computer Engineering

With busy lives, people sometimes forget to take breaks for multiple hours at a time. The purpose of this project is to remind the user to move around every hour if they have not already. To do so, stand will be a light weight fitness tracker that will detect the number of steps made within an hour. If the step count, dependent on goals, is not met then a vibration motor will gently remind them to take a break and walk. The data throughout the day will be shown on an iOS application where the user will be able to …

Roborodentia Robot (Amazon Prime), Alec Cheung

Computer Science and Software Engineering

Roborodentia is an annual autonomous robotics competition sponsored and hosted by Cal Poly. In the 2016 competition, participants are to design a robot that scores the most points by gathering rings from marked supply pegs and placing them onto marked scoring pegs. For Roborodentia I designed, constructed, and programmed a robot, named Amazon Prime, to compete.

Embedded System Design Of A Real-Time Parking Guidance System, Omkar Dokur

USF Tampa Graduate Theses and Dissertations

The primary objective of this work is to design a parking guidance system to reliably detect entering/exiting vehicles to a parking garage in a cost-efficient manner. Existing solutions (inductive loops, RFID based systems, and video image processors) at shopping malls, universities, airports etc., are expensive due to high installation and maintenance costs. There is a need for a parking guidance system that is reliable, accurate, and cost-effective. The proposed parking guidance system is designed to optimize the use of parking spaces and to reduce wait times. Based on a literature review we identify that the ultrasonic sensor is suitable to …

Rfid Microscope Lab, Patricia Carranza

Computer Engineering

The RFID Microscope Lab is a new exhibit created for the San Luis Obispo Children's Museum. The goal of the project is to create a modern, interactive exhibit that will teach children about different natural specimens through the use of technology. A computer, custom software, and RFID technology, will be used to display facts, microscopic images, and short videos of ten different specimens.