Civil and Environmental Engineering Commons^™

Construction Of Mse Wall Using Tire Shred-Sand Mixture As Backfill (Spr-3470), Monica Prezzi, Varenya Kumar Duvvuru Mohan

JTRP Other Publications and Reports

A large number of waste tires are generated each year throughout the world. Instead of disposing these tires in landfills, they can be used beneficially in road construction, MSE walls or structural fills that require large quantities of material. Such use of tires not only saves the costs of landfilling, but also provides certain desirable mechanical properties. The focus of this research was on determining important geotechnical properties of tire shred-sand mixtures required for their use as a lightweight backfill for MSE walls. Accordingly, the shear strength and pullout characteristics of tire shred-sand mixtures at various mixing ratios were determined …

The Marked Tree Site: Evaluation Of Geosynthetic Reinforcements In Flexible Pavements, Taylor Mitchell Goldman

Graduate Theses and Dissertations

This document presents findings from a three-year, full-scale, field research project aimed at determining the benefits of using geosynthetic reinforcements to improve the performance of flexible pavements constructed over poor subgrade soils. The test site, known as the Marked Tree site, is an 850-ft (258-m) long segment of low-volume frontage road along Highway 63 in the town of Marked Tree, Arkansas. The site, constructed in 2005, consists of seventeen 50-ft (15.2-m) long flexible pavement test sections with various types of geosynthetic reinforcements (woven and nonwoven geotextiles, and geogrids), which were all positioned at the base-subgrade interface, and two different nominal …

Effects Of High-Impedance-Contrast Boundary Upon Multi-Modal Seismic Surface Wave Data, Prajwol Tamrakar

UNLV Theses, Dissertations, Professional Papers, and Capstones

Synthetic studies and analyses of an experimental dataset were conducted to address the use of Rayleigh-type surface waves for estimation of shear wave velocity (VS) profiles of shallow bedrock sites. The shallow bedrock presents a high impedance contrast boundary which causes surface wave energy to be partitioned to higher modes. Idealized studies of hypothetical datasets and root-mean-squared calculations of error surfaces showed that if reliable dispersion data are available over a broad frequency spectrum, the VS profile can be recovered using the fundamental mode alone. However, when dispersion data are limited to a relatively narrow frequency band representing what might …

Hydraulic Conductivity Of Environmentally Controlled Landfill Liner Test Pad, Camila Maldonado Soria Galvarro

Civil Engineering Undergraduate Honors Theses

Laboratory and field hydraulic conductivity tests have been conducted on soil samples to develop and verify the zone of acceptance for liner placement. Compaction testing and flexible wall hydraulic conductivity tests were performed on fifteen (15) samples to determine the dry unit weight, molding water content, and laboratory permeability. Five of the fifteen samples were compacted at Standard proctor energy, five were compacted at 75 percent of Standard proctor energy, and five were compacted at 50 percent of Standard proctor energy. The results obtained from the laboratory portion of the testing program (the zone of acceptance) are presented. A ten …

Dimensional Stability Of Geosynthetic Clay Liners In Landfill Applications, Gregory R. Olsen

Master's Theses

An investigation was conducted related to the dimensional stability of geosynthetic clay liners (GCLs) in landfill applications. Multiple occurrences of panel separation of overlap seams in GCLs have been documented; however, explanation for the relative contribution of various mechanisms causing shrinkage has been limited. A systematic test program was conducted to determine the effects of a variety of conditions on GCL dimensional stability.

Effects of initial moisture content, permeant type, and overburden pressure were tested by subjecting various GCL products to wet-dry cycles and measuring the dimensional change with each cycle. Different GCL types were each tested under various combinations …

Thermal And Mechanical Studies Of Thin Spray-On Liner (Tsl) For Concrete Tunnel Linings, Taesang Ahn

Electronic Thesis and Dissertation Repository

The thesis presents a summary of Thin Spray-On Liner (TSL) effects on concrete. Three aspects, fire insulation, adhesion strength on concrete surface and load carrying capacity (i.e. flexural strength) on segmental concrete liners, are presented. Small-scale to full-scale laboratory tests were conducted using ASTM standards or devised methods. The TSL effects on three aspects were then compared with the results for uncoated concrete specimens. Numerical analyses using TEMP/W for the thermal response of TSL and a FE program, ABAQUS for the mechanical response of TSL were respectively carried out and compared with the measured results. Additionally, numerical analyses in respect …

Seismic Microzonation Of Great Toronto Area And Influence Of Building Resonances On Measured Soil Responses, Dimitar Genchev Mihaylov

Electronic Thesis and Dissertation Repository

A pilot seismic microzonation of the Greater Toronto Area (GTA) is used to establish the conditions and limitations of geophysical methods for site response investigations in city conditions. Maps of fundamental soil resonant frequencies, amplifications at these frequencies and interpolated average shear wave velocity of top 30 m of soil profile (VS- 30) used in soil classification were compared to the maps of drift thickness and surficial geology for the GTA. The non-applicability of the interpolated VS-30 map for site classification between measured test points is indicated. It is also shown that the soil response cannot be estimated properly using …

Seamless Bridge And Roadway System For The U.S. Practice, Nima Ala

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Expansion joints are one of the main causes for high maintenance costs in bridges. The search for ideal expansion joints has proven fruitless. That is why it has been said that “the best joint is no joint”. A seamless bridge system is envisioned that results in bridges with long service lives by eliminating the joints over the entire length of the bridge, approach slab and a segment of the roadway called transition. All bridge thermal movements are dissipated to zero in the transition. The system is similar to a system developed in Australia but modifications had to be made to …

Dissemination Of Geological Information In Avoiding Geotechnical Risks Associated With Tunnel Construction: Lessons Learned From Deep Voids In Marble In Lower Manhattan, New York City, Nazrul I. Khandaker, Stanley Schleifer, Masud Ahmed, Leah Scott

Publications and Research

Test boring associated with the recently accomplished City Water Tunnel # 3 in Manhattan, New York City revealed moderately to highly weathered marble with insoluble silicate residues composed mostly of phlogopite, chlorite, and tremolite. Apparent control on the weatherability of the marble was in response to original mineral constituents dominating this lithology. Encountered marble samples ranged between pure calcitic to mixed dolomitic/siliceous types. Fresh marble samples collected from adjacent boring locations revealed characteristic geochemical data: Lime (25-45%), Silica (4-7%), Alumina (1-3%), MgO (5-20%), and LOI (35-42%); compressive strength of unweathered marble varied between 2000-3000 Kg/cm². Relict foliations with …

Geotechnique, Physico-Chemical Behaviour And A New Erosion Model For Mine Tailings Under Environmental Loading, Rozalina S. Dimitrova

Electronic Thesis and Dissertation Repository

Comprehensive geotechnical characterisation of mine tailings is required for the design, construction and safe operation of mine waste management facilities against the large number of potential failure risks. It is important that the characterization is carried out under the stress range and drainage conditions relevant to those encountered in the field.

The present research utilized mine tailings samples from a copper/nickel base-metal mine. Kaolinite and bentonite clays were added to the mine tailings in order to study the effect of clay percentage and clay mineralogy on the behaviour of saturated tailings/clay systems with varying composition. Slurries with moderate or high …

Investigation Of Hybrid Monopile-Footing Foundation Systems Subjected To Combined Loading, Mohamed El-Marassi

Electronic Thesis and Dissertation Repository

Laterally loaded structures such as wind turbines, offshore platforms, earth retaining structures, bridge abutments and many other structures impose complex loading regimes on the supporting foundations. These foundations are typically subjected to combinations of vertical, horizontal and moment loadings resulting from the vertical self-weight of the foundation system, superstructure, soil fill and surface surcharge, in addition to significant lateral loads and moments due to soil pressures, wind loads, waves and currents. In the case of shallow foundations, the weight and dimensions must be sufficient to resist tilting and sliding, whilst at the same time preventing failure of the subsoil and …

Vibration Isolation Using In-Filled Geofoam Trench Barriers, Ashref Mohamed A. Alzawi

Electronic Thesis and Dissertation Repository

A significant amount of numerical and experimental research has been conducted to study the vibration isolation by wave barriers considering open trenches, in-filled concrete or bentonite trenches, sheet-pile walls, and rows of piles. A few studies have investigated the use of expanded polystyrene (EPS) geofoam material as wave barriers, which indicated that in-filled geofoam trenches can be used as effective wave barriers. However, no engineering design method is available to date for the design of such type of wave barriers. This dissertation presents comprehensive experimental and numerical investigations on the use of in-filled geofoam trench barriers to scatter machine foundations …

Development Of A High Strain-Rate Constitutive Model For Sands And Its Application In Finite Element Analysis Of Tunnels Subjected To Blast, William T. Higgins Iv

Master's Theses

This thesis describes the development of a constitutive model for simulating the high strain-rate behavior of sands and demonstrates the use of the model by analyzing underground tunnels subjected to blast. The constitutive model is based on the concepts of the critical state soil mechanics and bounding surface plasticity theory. The model captures the behavior of sand under multi-axial loading conditions and predicts both drained and undrained behavior at small and large strains. Perzyna’s overstress theory is incorporated in the model to simulate the viscoplastic behavior of sand under high strain rate. The model follows a nonassociated flow rule.

The …

Correlation Between Grain Dislocation Density And Orientation For Naturally Deformed Mantle Xenolith From Jagersfontein Mine, Quinton Guerrero, Quinlan Smith

Undergraduate Research Opportunities Program (UROP)

Determining the reaction of poly-crystalline structures to induced stress is an extremely difficult problem in contemporary engineering and geology. The main challenge lies in the inhomogeneity of the grains inside of the poly-crystalline structures. To predict the response of a certain polycrystalline structure to a specific stress, you must resort to one of two views on grain interaction, an orientation or propagation based model. For every material there may be certain correlations between the prediction model used and the actual deformation that occurred. Our work centers around describing the correlation of these prediction models with a sample of naturally deformed …

Constitutive Model For Rate Dependent Behavior Of Clay Internal Geotechnical Report 2011-3, Harry Martindale, Dipanjan Basu

Technical Reports

This report presents a strain-rate dependent plastic constitutive model for clays. Based on the concepts of critical-state soil mechanics and bounding surface plasticity theory, the model reproduces the mechanical response of clays under multi-axial loading conditions and predicts both the drained and undrained behavior. The model parameters are determined for Boston Blue Clay, London Clay and Kaolin Clay, and the performance of the model in simulating the mechanical response of these clays is demonstrated for low to medium strain rates. The sensitivity of each model parameter is checked by perturbing the calibrated values by ±20%. Subsequently, a probabilistic analysis using …

A High Strain-Rate Constitutive Model For Sand With Application In Finite Element Analysis Internal Geotechnical Report 2011-4, William Higgins, Dipanjan Basu

Technical Reports

The report presents a constitutive model for simulating the high strain-rate behavior of sands. Based on the concepts of critical-state soil mechanics, the bounding surface plasticity theory and the overstress theory of viscoplasticity, the constitutive model simulates the high strain-rate behavior of sands under uniaxial, triaxial and multiaxial loading conditions. The model parameters are determined for Ottawa and Fontainebleau sands, and the performance of the model under extreme transient loading conditions is demonstrated through simulations of split Hopkinson pressure bar tests up to a strain rate of 2000/sec. The constitutive model is implemented in a finite element analysis software to …

Dynamic And Static Performance Of Large-Capacity Helical Piles In Cohesive Soils, Mohamed A. Elkasabgy

Electronic Thesis and Dissertation Repository

Large-capacity helical piles can provide immense construction and performance advantages over the conventional concrete and steel piles. Nowadays, there is significant interest in using large-capacity helical piles to support foundations that would be subjected to both dynamic and static loading.

The main objectives of this thesis are to: investigate the dynamic response and impedances of large-capacity helical piles; develop an analysis methodology for their dynamic response; and investigate their static axial compression and lateral behaviour, considering installation effects on their dynamic and static performances. The thesis presents the first full-scale vertical and horizontal dynamic field testing program executed on large-capacity …

Development Of Sstreamflow Projections Under Changing Climate Conditions Over Colorado River Basin Headwaters, W. P. Miller, Thomas C. Piechota, S. Gangopadhyay, T. Pruitt

Civil and Environmental Engineering and Construction Faculty Research

The current drought over the Colorado River Basin has raised concerns that the US Department of the Interior, Bureau of Reclamation (Reclamation) may impose water shortages over the lower portion of the basin for the first time in history. The guidelines that determine levels of shortage are affected by relatively short-term (3 to 7 month) forecasts determined by the Colorado Basin River Forecast Center (CBRFC) using the National Weather Service (NWS) River Forecasting System (RFS) hydrologic model. While these forecasts by the CBRFC are useful, water managers within the basin are interested in long-term projections of streamflow, particularly under changing …

Fourier Finite Element Analysis Of Laterally Loaded Piles In Elastic Media Internal Geotechnical Report 2011-1, William Higgins, Dipanjan Basu

Technical Reports

Laterally loaded piles are analyzed using the Fourier finite element method. Pile response was observed to be a function of the relative stiffness of pile and soil and of the pile slenderness ratio. The analysis is mostly performed for piles embedded in elastic soil with constant and linearly varying modulus although the pile response in two-layer soil profiles is also investigated. Equations describing pile head deflection, rotation and maximum bending moment are proposed for flexible long piles and stubby rigid piles. The design equations were developed after plotting the pile responses as functions of pile-soil stiffness ratio and pile slenderness …

Sustainability In Geotechnical Engineering Internal Geotechnical Report 2011-2, Aditi Misra, Dipanjan Basu

Technical Reports

The built environment serves as a dynamic interface through which the human society and the ecosystem interact and influence each other. Understanding this interdependence is key to understanding sustainability as it applies to civil engineering. There is a growing consensus that delivering a sustainable built environment starts with incorporating sustainability thoughts at the planning and design stages of a project. Geotechnical engineering is the most resource intensive of all the civil engineering disciplines and can significantly influence the sustainability of infrastructure development because of its early position in the construction process. In this report, a review is made of the …

Gis-Based Data Model And Tools For Creating And Managing Two-Dimensional Cross Sections, Timothy L. Whiteaker, Norm Jones, Gil Strassberg, Alan Lemon, Doug Gallup

Faculty Publications

While modern Geographic Information Systems (GIS) software is robust in handling maps and data in plan view, the software generally falls short when representing features in section view. Further complicating the issue is the fact that geologic cross sections are often drawn by connecting a series of wells together that do not fall along a single straight line. In this case, the x-axis of the cross section represents the distance along the set of individual lines connecting the series of wells, effectively “flattening out” the cross section along this path to create a view of the subsurface with which …

Rate-Dependent Behavior Of Clay, Harry F. Martindale Iv

Master's Theses

This thesis presents a strain-rate dependent two-surface plasticity constitutive model for clays based on the critical-state soil mechanics. The model reproduces the mechanical response of clays under multi-axial loading conditions and predicts both drained and undrained behaviors at small and large strains. Model parameter values are determined for Boston Blue Clay, London Clay and Kaolin Clay. The performance of the model in simulating the mechanical response of clays is demonstrated for a variety of strain rates. Sensitivity of each model parameter is checked for ±5, ±10 and ±20% of the deterministic values. Probabilistic analysis using Monte Carlo simulations were done …

Investigating Properties Of Pavement Materials Utilizing Loaded Wheel Tester (Lwt), Hao Wu

Doctoral Dissertations

Loaded wheel tester (LWT) is a common testing equipment usually used to test the permanent deformation and moisture susceptibility of asphalt mixtures by applying moving wheel loads on asphalt mixture specimens. It has been widely used in the United States since 1980s and practically each Department of Transportation or highway agency owns one or more LWT(s). Compared to other testing methods for pavement materials, LWT features movable wheel loads that allow more realistic situations existing on the actual pavement to be simulated in the laboratory. Due to its potential of creating a condition of repetitive loading, the concept of using …

Em Stimulation Of Water For Geotechnical Applications, Harlan Dwight Olson Sangrey

Boise State University Theses and Dissertations

The task of cleaning soil and/or groundwater contaminated by leakage from aging underground gasoline or petrochemical tanks along with surface spills of gasoline and other hazardous chemicals is of utmost importance for federal and state environmental agencies. Traditional clean up and contaminant removal involves dig-and-treat methods that are costly and impractical for large, contaminated sites. Less disruptive remediation techniques, such as air sparging, have become more attractive in the past decade. Air sparging, bioventing, and other remediation technologies that use air injection into soil can become very effective for non-aqueous phase liquid (NAPL) removal using volatilization and bioremediation. However, the …

Complex Vs Profiles To 100 M Depth From Rayleigh Waves And 3-D Vs Model For Las Vegas Valley, Helena Murvosh

UNLV Theses, Dissertations, Professional Papers, and Capstones

A three-dimensional (3-D) shear wave velocity (VS) model was developed for the heterogeneous shallow sediments (to nearly 400 m) of the Las Vegas Valley (LVV), Nevada. The model was based on more than 200 VS profiles and 1400 geologic well logs. Five sediment units including a cemented unit were defined from geologic log descriptions. A characteristic VS profile for four of the units was obtained by correlating between closely spaced pairs of VS and sediment data; a constant VS was assigned to the cemented unit. VS profiles were then assigned to each well location based on type of sediment according …

Evaluation Of Wind-Induced Resuspension On The Performance Of A Mine Tailings Storage Facility, Laxmi Kant Kachhwal

Electronic Thesis and Dissertation Repository

Proper management of sulphide rich reactive mine tailings is a growing concern for mining industries. Oxidation of tailings can release acids and toxic metals into the surroundings, which can potentially pollute the ecosystem. Confining tailings under shallow water covers is one of the most successfully applied technologies for long-term storage. The water has lower solubility and diffusivity of oxygen than air and can significantly reduce the influx of oxygen to the bed tailings. However, wind-induced waves and currents in the water can resuspend bed tailings and ultimately result in oxidation.

Extensive field investigations were carried out to evaluate the performance …

The Behaviour Of Cement Stabilized Clay At High Water Contents, Saeed Sasanian

Electronic Thesis and Dissertation Repository

Artificial cementation of soft clays has been used for several years for different ground improvement projects. Although considerable work has been done to develop advanced machinery and techniques for the implementation of artificial cementation, less knowledge is available on the mechanisms involving the formation of the artificial structure and the resulting mechanical behaviour. The primary objectives of the present work were to investigate the formation of microstructure in artificially cemented material with Portland cement, find the relationships between cementitious bonding and clay mineralogy, and create constitutive frameworks for predicting the mechanical behaviour of cement-treated clays.

Qualitative and quantitative microstructural characterisation …

Influence Of Nozzle Pressure, Standoff Distance, And Reinforcing Steel Cage On Water Jetting Of Cidh Pile Anomalies, Matthew Jason Schaffer

Master's Theses

The effectiveness of removing anomalous material from cast-in-drilled-hole (CIDH) piles by water jetting was examined. The primary objectives of this research were to examine how reinforcing steel influences water jetting and to evaluate how jetting pressures and standoff distance from the material surface affect water jetting of concrete type materials and PVC tubing. The experimental work consisted of water blasting submerged test specimens using rotary jets, nozzles, pumping equipment, and testing procedures currently used in construction practice. The concrete test specimens were comprised of ring- and cylinder-shaped samples, containing materials with compressive strengths of approximately 160 and 3,600 psi. Typical …

Probabilistic Fault Displacement Hazard Analysis For Reverse Faults And Surface Rupture Scale Invariance, Zachary E. Ross

Master's Theses

p.p1 {margin: 0.0px 0.0px 0.0px 0.0px; font: 12.0px 'Times New Roman'}

A methodology is presented for evaluating the potential surface fault displacement on reverse faults in a probabilistic manner. This methodology follows the procedures put forth for Probabilistic Fault Displacement Hazard Analysis (PFDHA). Empirical probability distributions that are central to performing a PFDHA are derived from field investigations of reverse faulting events. Statistical analyses are used to test previously assumed properties of scale invariance with respect to magnitude for normalized displacement. It is found that normalized displacement is statistically invariant with respect to magnitude and focal mechanism, allowing for the …

Hydraulic Conductivity Of Model Soil-Bentonite Backfills Subjected To Wet-Dry Cycling, Michael A. Malusis, Jeffrey C. Evans, Seungchoel Yeom

Faculty Journal Articles

The potential for changes in hydraulic conductivity, k, of two model soil-bentonite (SB) backfills subjected to wet-dry cycling was investigated. The backfills were prepared with the same base soil (clean, fine sand) but different bentonite contents (2.7 and 5.6 dry wt %). Saturation (S), volume change, and k of consolidated backfill specimens (effective stress = 24 kPa) were evaluated over three to seven cycles in which the matric suction, Y_m, in the drying stage ranged from 50 to 700 kPa. Both backfills exhibited susceptibility to degradation in k caused by wet-dry cycling. Mean values of …