Civil and Environmental Engineering Commons^™

Efficient Sintering Of Lunar Soil Using Concentrated Sunlight, Diprajit Biswas

Electronic Theses and Dissertations

Construction material is one crucial need for long-term habitation on the moon. When concentrated for high heat flux, solar radiation can heat lunar soil or regolith until it sinters at temperatures above 900°C. The solid, sintered soil simulant can be used as construction material. This work explores the conditions leading to effective lunar soil sintering for both direct and indirect irradiated sintering. Lunar soil simulants were sintered using concentrated light from a xenon-arc lamp with varying heat flux intensity. During direct sintering of LHS-1, a sintering range of 860°C-1140°C corresponding to a peak heat flux of 105-120 kW/m2 was identified …

Studying The Effects Of Various Process Parameters On Early Age Hydration Of Single- And Multi-Phase Cementitious Systems, Rachel Cook

Doctoral Dissertations

”The hydration of multi-phase ordinary Portland cement (OPC) and its pure phase derivatives, such as tricalcium silicate (C₃S) and belite (ß-C₂S), are studied in the context varying process parameters -- for instance, variable water content, water activity, superplasticizer structure and dose, and mineral additive type and particle size. These parameters are studied by means of physical experiments and numerical/computational techniques, such as: thermodynamic estimations; numerical kinetic-based modelling; and artificial intelligence techniques like machine learning (ML) models. In the past decade, numerical kinetic modeling has greatly improved in terms of fitting experimental, isothermal calorimetry to kinetic-based modelling …

Optimal Sintering Temperature Of Ceria-Doped Scandia Stabilized Zirconia For Use In Solid Oxide Fuel Cells, Amanda K. Assuncao

Honors Undergraduate Theses

Carbon emissions are known to cause decay of the Ozone layer in addition to creating pollutant, poisonous air. This has become a growing concern among scientists and engineers across the globe; if this issue is not addressed, it is likely that the Earth will suffer catastrophic consequences. One of the main culprits of these harmful carbon emissions is fuel combustion. Between vehicles, power plants, airplanes, and ships, the world consumes an extraordinary amount of oil and fuel which all contributes to the emissions problem. Therefore, it is crucial to develop alternative energy sources that minimize the impact on the environment. …

Fabrication And Modification Of Titania Nanotube Arrays For Harvesting Solar Energy And Drug Delivery Applications, Ahmed El Ruby Abdel Rahman Mohamed

Electronic Thesis and Dissertation Repository

The fast diminishing of fossil fuels in the near future, as well as the global warming caused by increasing greenhouse gases have motivated the urgent quest to develop advanced materials as cost-effective photoanodes for solar light harvesting and many other photocatalytic applications. Recently, titania nanotube arrays (TNTAs) fabricated by anodization process has attracted great interest due to their excellent properties such as: high surface area, vertically oriented, highly organized, one-dimensional, nanotubular structure, photoactivity, chemical stability and biocompatibility. This unique combination of excellent properties makes TNTAs an excellent photoanode for solar light harvesting. However, the relatively wide band gap energy of …

Microstructural Analysis Of Thermoelastic Response, Nonlinear Creep, And Pervasive Cracking In Heterogeneous Materials, Alden C. Cook

Electronic Theses and Dissertations

This dissertation is concerned with the development of robust numerical solution procedures for the generalized micromechanical analysis of linear and nonlinear constitutive behavior in heterogeneous materials. Although the methods developed are applicable in many engineering, geological, and materials science fields, three main areas are explored in this work. First, a numerical methodology is presented for the thermomechanical analysis of heterogeneous materials with a special focus on real polycrystalline microstructures obtained using electron backscatter diffraction techniques. Asymptotic expansion homogenization and finite element analysis are employed for micromechanical analysis of polycrystalline materials. Effective thermoelastic properties of polycrystalline materials are determined and compared …

Studies In Modulation Of Interfacial Reactions For Certain Sulphide Minerals, Robert Owen Beyaert

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

Preliminary Examination Of The Aluminum Corner Of The Ternary System Aluminum-Silver-Indium (A1-Ag-In), Jerome J. Blake

Bachelors Theses and Reports, 1928 - 1970

In this paper the author attempts to lay the groundwork for future work on the Al-Ag-In system.

Production Of Standard-Grade Ferromanganese In An Electric Arc Furnace, Force F. Baney Jr.

Bachelors Theses and Reports, 1928 - 1970

The investigations conducted in this project were essentially concerned with the effects of various compositions of two different slag systems upon the increased recovery of manganese in a standard-grade ferromanganese.

Investigation Of The Ternary System Silver-Aluminum-Indium (Ag-Al-In), Elvin H. Beardslee

Bachelors Theses and Reports, 1928 - 1970

This thesis paper contains material pertaining to & preliminary investigation of the ternary system Ag-Al-In. Procedures in this preliminary investigation are discussed in detail.

Crystal Habit Modification Of Sodium Chlorate, Michael R. Keegan

Bachelors Theses and Reports, 1928 - 1970

All single crystals have a particular habit or morphology. The crystal habit refers to the relative degree of development of crystallographic planes into surfaces which make up the external appearance of the single crystal.

In this paper, NaClO3 is used as a parent crystal. Its simple cubic habit is modified to tetrahedral by the use of impurities of SO4=, S2O3=, Cr2O7=, and NO3-. The degree of habit change is studied as a function of impurity concentration and temperature. The problem and phenomena are explained in terms of surface chemistry and thermodynamics.

Physico-Chemical Principles Of Sixteenth Century Metallurgy, Robert E. Johnson

Bachelors Theses and Reports, 1928 - 1970

Following a review of sixteenth century metallurgical literature and a discussion of Gibbs free energy, this thesis discusses thermodynamic considerations of galena (PbS) reduction by iron from a lead assay of this period. The importance of fluxes in this assay is emphasized. The discussion covers both equilibrium and non-equilibrium conditions at 1100 degrees Celsius. Possible substitutes for iron are also covered.

Information from twenty-one small controlled lead assays is correlated with the thermodynamic discussion to determine the purpose of each constituent in the assay.

The Beneficiation Of Titaniferous-Magnetite Sands, Ronald Lloyd Nordwick

Bachelors Theses and Reports, 1928 - 1970

The purpose of this investigation of beneficiation methods is to develop and study possible economic methods for recovering an iron-titanium concentrate of sufficient purity to meet metallurgical requirements for subsequent direct reduction to pig iron and a high titanium slag.

Stress-Corrosion Cracking Of Brass, Paul A. Fossey

Bachelors Theses and Reports, 1928 - 1970

the mechanism of stress-corrosion cracking of brass has been sought for many years. Investigators have proposed many mechanisms, but each of these mechanisms has always had several drawbacks. This paper presents an account of experimental work done in the laboratory on this subject and compares it to the work of previous investigations. It evaluates the mechanisms presented by investigators and shows the failures of these mechanisms. A theory of Nitrogen Embrittlement is presented and an evaluation of this theory with experimental work follows.

Experimental Arc Furnace Smelting Of Titaniferous Iron Sands From The Northern Oregon Coast, Allan P. Herring

Bachelors Theses and Reports, 1928 - 1970

This investigation is an attempt to experimentally smelt titaniferous iron sands from the Northern Oregon Coast in a laboratory arc furnace.

The Effect Of Ph Upon Chelation Reactions In Montmorillonite Clays, Joseph Michael Keane

Bachelors Theses and Reports, 1928 - 1970

The purpose of this thesis is to investigate several chelation reactions and determine the effect of variable pH upon these reactions.

An Investigation Of The Sintering Of Iron-Wire Compacts, George L. Vivian

Bachelors Theses and Reports, 1928 - 1970

A study of the sintering of iron has been made by observing the rate of bonding of iron wires wound on iron spools. The specimens were sintered at a constant temperature of 850c in vacuum furnaces capable of producing pressures of 10-5 to 10-4 mm of mercury, and the growth of the bond between wires was observed as a function of time.

It has been concluded that the volume-diffusion mechanism is strongly operating in the sintering of iron at 850c, but in an evacuated system, the evaporation-condensation mechanism also contributes to the sintering process.

The Identification Of Montana Clays By X-Ray Analysis, David Stephen Malyevac

Bachelors Theses and Reports, 1928 - 1970

The purpose of this study is to identify the various Montana clay minerals by means of X-ray diffraction. The ultimate aim of this investigation is to identify the different clay mixtures through an analysis of their respective diffraction patterns, and diffraction patterns obtained after various chemical and thermal treatments.

Investigation Of Inclusions In Armco Ingot Iron, Edwin J. Duncan

Bachelors Theses and Reports, 1928 - 1970

Various chemical and electrolytic separation methods were investigated in an attempt to separate the in­clusions in Armco ingot iron. Residues obtained were X-rayed for identification purposes. The microstruc­tures of this iron were studied with the object of de­termining the relative sizes, locations, and possible compositions of the inclusions.

The Design And Construction Of An Electrolytic Cell For Aluminum Reduction, Thomas H. Melrose

Bachelors Theses and Reports, 1928 - 1970

The purpose of this investigation was to design and construct a laboratory size electrolytic cell in which to reduce alumina, using the same basic materials that are used in a commercial size cell. The cell was designed to have a capacity of approxi­mately 100 grams of metallic aluminum produced every 8 hours. The cell was constructed so it could be operated continuously.

Effect Of Recovery On The Recrystallized Grain-Size Of High Purity Aluminum, Rodney L. Helterline

Bachelors Theses and Reports, 1928 - 1970

When a cold-worked metal is annealed, it’s physical properties hange as a result of a new grain structure. The annealing treatment is divided into three stages according to the changes that occur in the distorted metal: (1) recovery, (2) recrystallization, and (3) grain growth.

Geology Of The Ragged Point Oil Field Musselshell County, Montana, David M. Amos

Bachelors Theses and Reports, 1928 - 1970

The Ragged Point oil field is located in Northwest Musselshell County, in the Lake Basin field of central Mon­tana, and on the western border of the Great Plains region. The surface topography is that of a plain marked by erosion and moderate folding. The stratigraphy of central Montana shows periodic marine invasions from the Cordilleran trough, with normal marine limestones interbedded with sandstone sand shales. These sediments are over 12,000 feet thick, with the Creta­ceous Eagle and Colorado formations exposed at the surface on the Ragged Point anticline. Undifferentiated Cambrian lime­stones and shales are the oldest rocks encountered in drilling.

Polarography Of Indium, John Jackson

Bachelors Theses and Reports, 1928 - 1970

The purpose of this thesis is to study the various aspects of the polarography of indium. The eventual goal would be to develop a method of analyzing indium in unknowns. The investigation is approached by studying the indium ions in various electrolytes and in various concentrations.

The Application Of Electric Energy To The Metallurgy Plants In Montana, Edwin J. Duncan

Bachelors Theses and Reports, 1928 - 1970

Since the year 1800, metallurgy has been affiliated with electricity. In fact, the two industries have grown side by side, being naturally dependent upon each other and having a parallel growth.

The Construction And Operation Of A Universal Specimen Mount With Protective Lead Shield For The Purpose Of Determining Pole Figures Using The Schulz-Decker Transmission Technique, Richard L. Fausner

Bachelors Theses and Reports, 1928 - 1970

It was the purpose of this study to construct a universal mount, to construct a protective lead shield, to operate the instrument, and to provide a pole figure using the transmission method of Schulz and Decker. There are at present several lengthy x-ray methods of determining the grain orientation of metals. These methods are mainly photographic. In order to provide a rapid means of obtaining the necessary information concerning the grain orientation of a metal, a universal mount was constructed.

The Lucky Hit Mine Of Jefferson County, Montana, Bruce B. Goddard

Bachelors Theses and Reports, 1928 - 1970

Many mines in the Cardwell Mining District have been more or less steady producers of gold, silver, lead and zinc since 18SO. The area first came into prominence with the discovery of gold at the Mayflower Mine in 1896. Soon after the Mayflower discovery, many claims were located in the nearby Saint Paul Gulch area, northeast of Whitehall. The Lucky Hit Mine is located in Saint Paul Gulch area of the Cardwell Mining District.

Nonmetallic Mineral Resources Of Montana (Except Fuels), F. L. Rytlewski

Bachelors Theses and Reports, 1928 - 1970

Essentially, the paper is composed of seven parts, each of which concerns a group of related nonmetallic minerals such as ceramic materials, gemstones, or abra­sives. Following the data pertaining to the minerals of each group are index mars locating the major mineral deposits which are known to date. Production and reserve figures are listed by tables in cases where such information is available.

The Flotation Concentration Of A Complex Low-Grade Lead Zinc Ore, Edward James Fong

Bachelors Theses and Reports, 1928 - 1970

This report is concerned primarily with the beneficiation of a low-grade complex lead-zinc ore. The depletion of high grade veins has caused the mineral engineer to seek deposits deeper in the earth's crust or to find lower grade deposits. The other alternative has placed more research problems on Mineral Dressing Engineers in particularly the iron, copper, lead and zinc fields.

Host Rocks And Gangue Minerals Associated With Copper Deposits In Plutonic Igneous Rocks, Richard D. Montgomery

Bachelors Theses and Reports, 1928 - 1970

All of the information on the various districts has come directly from published reports. The investigation was suggested by Mr. Forbes Robertson. The geographical extent of the deposits was confined to the western United States. Many of these deposits are of the disseminated porphyry type. A few of the de­posits, such as at Butte, Montana, were of the fissure vein type.

Studies Of Tempering Behavior Of Steel X-9165 Of N-A-X 9100 Series, James A. Ndulue

Bachelors Theses and Reports, 1928 - 1970

One of the reasons why steel is the most versatile of all the metals available for engineering applications is because of the wide range of properties that can be obtained from it by proper heat treatment.

Geology Of The Marget Ann Mine Butte District, Montana, Winston Martin Sahinen

Bachelors Theses and Reports, 1928 - 1970

As the field work progressed it became apparent that very little was known of the mineralogical associations of the precious metal constituents of the Marget Ann ore. A mineralogical study in excess of that originally planned was then decided upon to de­termine the affiliations exhibited by the silver and gold. With these objectives in mind, the laboratory and field work continued.