Chemical Engineering Commons^™

Iodat Analysis Content In Cooking Ingredients Using Iodometry And X-Ray Fluorescence Methods., Nelson Saksono

Makara Journal of Technology

Iodat Analysis Content in Cooking Ingredients Using Iodometry and X-ray Fluorescence Methods. Salt iodization program using iodine fortification into salt method is the best method that is effective and economical to overcome the problems caused by iodine deficiency. However in, its development there are some issues clamed that the use of iodized salt is ineffective since iodine content reduces, even disappear when the salt mix with other cooking ingredients. In order to investigated the existence of iodine in cooking ingredients, a research applying iodometry and X-ray fluorescence methods was carry out. The result obtained by iodometry method showed decreases in …

Emission Gas Reducer On Motor Vehicle, Automobile, Light Engine Of Boat And Stationary Combustion Engine., I Gusti Bagus Wijaya Kusuma

Makara Journal of Technology

Emission gas reducer on motor vehicle, automobile, light engine of boat and stationary combustion engine. The use of motor vehicle should be followed by protection against damages on the environment, since the exhaust gas from combustion engine has significantly affect on air and environmental pollution. One method to solve the problems in air pollution has been done by using a re-heater designed in Mechanical Engineering Department, University of Udayana. In accordance to the test on the re-heater, it can be seen very clear that the re-heater has significantly reduce the CO emission of about 54%. It also reduces the CO2 …

Application Of Remote Sensing For Mapping Soil Organic Matter Content, Bangun Muljo Sukojo, Wahono Wahono

Makara Journal of Technology

Application of Remote Sensing for Mapping Soil Organic Matter Content. Information organic content is important in monitoring and managing the environment as well as doing agricultural production activities. This research tried to map soil organic content in Malang using remote sensing technology. The research uses 6 bands of data captured by Landsat TM (Thematic Mapper) satellite (band 1, 2, 3, 4, 5, 7). The research focuses on pixels having Normalized Difference Soil Index (NDSI) more than 0.3. Ground-truth data were collected by analysing organic content of soil samples using Black-Walkey method. The result of analysis shows that digital number of …

Optimation Model Of Planning Investment Dockyard With Approach Multi Objective Goal Programming, Ali Azhar

Makara Journal of Technology

Optimation model of planning investment dockyard with approach multi objective goal programming. The purpose of this research is to determine decision variable, goal function, alternative priority and achievement function in investment planning. From this optimation component, the model of ship yard investment planning could be achieved. The model of developed model in this research was the optimation of ship yard investment planning using multi objective goal programming approach. The model consist of 5 decision variable, 11 goal function, 2 alternative priority and 11 achievement functions. The model implementation was done toward PT ASSI investment planning. The calculation using from Quantitative …

The Use Of 2d Plastic Grating For Surface Profile And Dimension Manufacture Product Measurements By Using Ndt Moiré Technique, Retno Wigajatri P., Dini Andiani

Makara Journal of Technology

The Use of 2D Plastic Grating for Surface Profile and Dimension Manufacture Product Measurements by Using NDT Moiré Technique. Research of measuring the shape and dimension of object using the moiré technique have been done. Measurement have been made by observing the moiré space as a result of interaction between grating and its shadow casted on the object’s surface caused by the projector lamp with CCD camera. The acquired data was further processed by way of off-line. By successive phase shifts that is π/2, π dan 3π/2 towards the table tennis ball at the distance of 48 cm from the …

Self-Ignition Properties Of Peat, Palm Shell Fibre And Woods, Yulianto Sulistyo Nugroho

Makara Journal of Technology

Self-ignition properties of peat, palm shell fibre and woods. Forest fire is one of the greatest environmental problems faced by Indonesia. Forest fires have destroyed million hectares of forest and land which cause economic loss, social problems including smoke related diseases and environmental disaster with long time consequences. The exothermic reactions of forest fuels that lead to fire can be initiated by a piloted flame and low-temperature oxidation mechanism. This paper presents the results of low temperature oxidation studies using forests fuel samples i.e. palm shell fibre, peat, woods and low-rank coal. The measured values of the critical oven temperatures …

The Effect Of Convection On Disorder In Primary Cellular And Dendritic Arrays, R. Trivedi, P. Mazumder, Surendra N. Tewari

Chemical & Biomedical Engineering Faculty Publications

Directional solidification studies have been carried out to characterize the spatial disorder in the arrays of cells and dendrites. Different factors that cause array disorder are investigated experimentally and analyzed numerically. In addition to the disorder resulting from the fundamental selection of a range of primary spacings under given experimental conditions, a significant variation in primary spacings is shown to occur in bulk samples due to convection effects, especially at low growth velocities. The effect of convection on array disorder is examined through directional solidification studies in two different alloy systems, Pb-Sn and Al-Cu. A detailed analysis of the spacing …

Steady State Simulation Of Ysz Intermediate-Temperature Fuel Cell, Zi-Jing Lin, Ye Gu, Xiao-Hua Zhang

Journal of Electrochemistry

With a coupled 2D electrochemical and thermal modeling software, the characteristics of the steady state operation of the intermediate-temperature fuel cell with thin yttria-stabilized zirconia(YSZ) electrolyte was analyzed. The parameters of I-V equation were obtained from fitting the experiment results and the choice of grid points was determined by balancing the accuracy requirement and computational efficiency. The temperature fields at different operation circumstances such as flow designs, material choices for interconnect, were examined. The dependences of the output power and cell efficiency on the operating voltage at different temperatures were studied. Based upon the analysis of the temperature profile, it …

Preparation And Performance Of Lifeo_2 Coated Nickel Oxide Cathode For Molten Carbonate Fuel Cells, Chun-Ming Wang, Fei Li, Ke-Ao Hu

Journal of Electrochemistry

A novel cathode for molten carbonate fuel cells was prepared by coating LiFeO 2 over the surface of porous NiO cathode by a simple combustion process. The analytical results of X-ray diffraction (XRD), energy dispersive analysis of X-ray (EDAX), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) indicated that the LiFeO 2 coating on the surface of NiO particles consisted of nonometer-sized LiFeO 2 grains and sintered tightly with the NiO particles. The LiFeO 2 coating dramatically reduced the contacting area of NiO with the carbonate melts, thus the solubility of NiO in the carbonate melts was decreased. Meanwhile, …

Nano-Sized Cobalt-Based Oxides As Negative Electrode For Lithium-Ion Batteries, Feng Huang, Zheng-Yong Yuan, Yun-Hong Zhou, Ju-Tang Sun

Journal of Electrochemistry

Nanosized cobalt-based oxide (Co 3O 4, CoB 1.36 O 2.8 and CoB 0.5 Al 0.1 O 1.5 ) samples were prepared by rheological phase method and were tested as anodes in secondary lithium batteries. The cells were cycled between 0.01V and 3.00 V. The best electrochemical performance was obtained from the Li/Co 3O 4 cell, which retained 95% of its initial capacity (931 mAh/g) after 30 cycles. The doping of B, Al reduced the reversible capacity during the first discharge/charge cycle, and the quantity of reversible capacity reduced with B, A1 increasing. The modifying structures at difference charge and discharge …

Electrocatalytic Oxidation Of Formic Acid On Molybdate-Modified Platinum Electrode, Jun-Hua Du, Xue-Hui Xu, Hong Li, Hong-Yu Cheng, Wei-Shan Li

Journal of Electrochemistry

The electrochemical behavior of molybdates on a platinum electrode in H 2SO 4 solutions with different H 2SO 4 concentrations was studied by cyclic voltammetry and double chronoamperometry. Molybdates were reduced to adsorb hydrogen molybdenum bronzes on the platinum electrode in H 2SO 4 solutions during cathodically potential sweep. The hydrogen molybdenum bronzes were oxidized to different forms of hydrogen molybdenum bronzes with less hydrogen, depending on the H 2SO 4 concentration. Platinum electrode was modified by these hydrogen molybdenum bronzes. However, this modified electrode was not stable in H 2SO 4 solutions. The modified electrode was used to study …

Mechanistic Study Of Oxidation Of Hypophosphite On Pt Electrodes By Sniftirs, Tai-Xiang Jiang, Hui-Huang Wu

Journal of Electrochemistry

The oxidation of hypophosphite on a polycrystalline platinum electrode was studied by SNIFTIRS and cyclic voltammetry, the in-situ IR spectra were analyzed as a function of Pt electrode potentials in the solution of 0.5 mol/L H 2SO 4+0.1 mol/L NaH 2PO 2. It was found that the dissociative adsorption of hypophosphite ions occurs on Pt surface, and the oxidation product is H 3PO 4, rather than H 2PO 3 - which was considered to produce on Ni electrodes, thereby a new insight into mechanism of hypophosphite oxidation on Pt in acidic media was provided.

Review Of Mathematical Model For Proton Exchange Membrane Fuel Cell, Shan-Hai Ge, Bao-Lian Yi, Hua-Min Zhang

Journal of Electrochemistry

In the review with 49 references, the mathematical models for proton exchange membrane fuel cell (PEMFC) were summarized. The mechanistic model and empirical model were introduced. Transfer in the membrane, catalyst layer,diffusion layer and flow field of PEMFC were described. The importance of water and heat management was analyzed. The dimension, complexity and solving methods of the PEMFC model were discussed. The importance and validity to develop a model with time dimension are put forward.

Manufacture Of 1 Kw Molten Carbonate Fuel Cell Stack, Sheng Sui, Xin-Jian Zhu, Zheng-Yu Fan, Cao Guang-Yi And

Journal of Electrochemistry

A molten carbonate fuel cell stack with an active area of 240 mm×140 mm consisted of 30 cells.The gas feed system works via interior manifolds,and the stack placed in a couple of self-chest,coupled with a heater at the bottom and other fours surrounded,to keep uniformity of temperature.Under ambient pressure and 650 ℃,fed with hydrogen and air as anode and cathode gases respectively,the stack gave a current density of 150 mA/cm 2 at an average cell voltage of 0.7 V.The peak output of the stack was 1.06 kW during its performance of 300 h.

Synthesis And Characterization Of Lini_(0.8-X)Al_Xco_(0.2)O_2 As Cathodes For Lithium-Ion Batteries, Jun Zhang, Zhong-Kao Jin, Qing-He Yang, Qing-Mei Song, Xiao-Hua Ma, Xiang-Fu Zong

Journal of Electrochemistry

Single_phase solid solution of LiNi 0.8- x Al x Co 0.2 O 2 (0≤ x <0.1)had been synthesized and characterized by X_ray diffraction(XRD) and scanning electron microscopy (SEM). Their electrochemical performance was examined by charge_discharge cycling.The LiNi 0.71 Al 0.09 Co 0.2 O 2 compound showed a discharge capacity of 152 mAh/g after 20 cycles that corresponds to 97.4% capacity retention. The beneficial effect of co_doping with Al and Co elements was corro_borated by slow scanning cyclic voltammograms(SSCV),electrochemical impedance spectrum(EIS)and differential scanning calorimetry(DSC) data on charged cathodes. These results show that the 2D_character of the crystal lattice was stabilized by co_doping with Al and Co, the phase transitions that occur during deintercalation or intercalation of Li_ions were significantly suppressed,and thermal stability in the charged state was also improved.

Ionic Conduction In Ba_(0.95)Ce_(0.9)Y_(0.1)O_(3-Α)Solid Oxide And Its Performance In Fuel Cell, Gui-Lin Ma, Ding-Xian Jia, Li-Gan Qiu, Hui Shi, Rong Chen

Journal of Electrochemistry

Using Ba 0.95 Ce 0.9 Y 0.1 O 3-α as a solid electrolyte and porous platinum as electrodes,hydrogen and oxygen concentration cells and hydrogen_air fuel cell were constructed,respectively.Electromotive forces(MEFs)of the gas concentration cells and I_V characteristics of the fuel cell were detdrmined in the temperature range of 600～1 000 ℃.The Ba 0.95 Ce 0.9 Y 0.1 O 3-α exhibited almost the pure protonic conduction under hydrogen gas,and a mixed conduction of oxide_ion and electron hole with oxide_ion transport number of 0.3～0.5 under oxygen gas.It exhibited a mixed conduction of proton and oxide_ion with the total ion transport number above 0.9 …

Optimum Of Catalyst Layers For Direct Methanol Fuel Cells, Jun Zhang, Lei Li, Li Xu, Yu-Xin Wan

Journal of Electrochemistry

The performances of membrane electrode assemblies (MEAs)with various Pt loading were compared.The amount of Nafion in a catalytic layer was optimized,and the effect of Nafion loading on the resistance of MEAs was investigated with ac impedance spectroscopy.For a MEA with both Pt 4 mg/cm 2 in the anode and the cathode,suitable Nafion loading was 21.4 wt% in the anode.With 21.4 wt% Nafion loading in the cathode,the Direct Methanol Fuel Cells(DMFC) showed the highest performance at high current density.While,the DMFC performances came down,as Nafion loading increasing,for ohm and concentration polarization.

Electrically-Small Low Q Radiator Structure And Method Of Producing Em Waves Therewith, Craig A. Grimes, Dale M. Grimes, Faton Tefiku, Gang Lui

Chemical and Materials Engineering Faculty Patents

An electrically small radiator structure for radiating electromagnetic waves having an electrical size, k*a, with a value less than π/2 and above π/20,000 and configured to have at least a first and second magnetic, or electric, dipole element. Dipole elements are preferably oriented such that a source-associated standing energy value for the structure, or W_ds(t_R), is low, Radiative Q value preferably less than ⅓(k*a)³; and each of the elements, whether paired with respective electric dipole elements, is in electrical communication through a feed circuit to at least one power source. Further, a first …

The Effects Of Corrosive Chemicals On Corrosion Rate Of Steel Reinforcement Bars: Ii. Swamp Sludges, Henki W. Ashadi, Sulistyoweni Widanarko, Irma Gusniani

Makara Journal of Technology

A polluted environment will influence the building age. The objective of this research was to find out the influence of corrosive chemicals within the sludge swamp area with the corrosion rate of steel concrete. Corrosion in steel concrete usually occur in acid area which contain of SO4 2-, Cl- and NO3 -. The research treatment used by emerging ST 37 and ST 60 within 60 days in ‘polluted’ sludge swamp area. Three variation of ‘polluted’ swamp sludge were made by increasing the concentration a corrosive unsure up to 1X, 5X and 10X. The corrosion rate measured by using an Immersion …

The Effects Of Corrosive Chemicals On Corrosion Rate Of Steel Reinforcement Bars: I. Swamp Water, Sulistyoweni Widanarko, Henki W. Ashadi, Andri Krisnadi Wicaksono

Makara Journal of Technology

Most of infrastructures using steel concrete to reinforce the strength of concrete. Steel concrete is so vulnerable to chemical compounds that can cause corrosion. It can happen due to the presence of chemical compounds in acid environment in low pH level. These chemical compounds are SO4 2-, Cl-, NO3 -. There are many swamp area in Indonesia. The acid contents and the concentration of ion sulphate, chlorides, and nitrate are higher in the swamp water than in the ground water .The objective of this research was to find out the influence of corrosive chemicals in the swamp water to the …

The Effect Of Ca Content On Cao-Zeolite On Nitrogen Adsorption Capacity, Mohammad Nasikin, Tania Surya Utami, Agustina Tp Siahaan

Makara Journal of Technology

In industry, Ca zeolite is used as nitrogen selective adsorbent with the use of PSA (Pressure Swing Adsorption)/VSA (Vacuum Swing Adsorption) methods. Natural zeolite modified to be Cao-zeolite by ion exchange process using Ca(OH)2. Adsorption test was done on CaO-zeolite with different Ca concentration to understand how it’s adsorption phenomena on oxygen and nitrogen. Adsorption test has been done for CaO-zeolite with Ca concentration = 0,682%, 0,849% and 1,244% to oxygen and nitrogen with equal concentration seperately. Pressure variation has being done three times (5 minutes long each time) adsorption time to analyze the connection between adsorption time and how …

Development Of Hardness Measurement Procedure For Nanocomposite Nc-Tin/A-Si3n4, Keba Moto

Makara Journal of Technology

Hardness of nc-TiN/a-Si3N4 nanocomposites which was determined by using two methods of measurements i. e. depth sensing method and remaining plastic indentation area that were magnified by using SEM (Scanning Electron Microscope) lie in the good agreement. The hardness value is not influenced by the biaxial and residual compressive stress. The measurement of the biaxial stress on the substrate shows a very small value of biaxial stress as well as the constant hardness and crystallite size against annealing temperature. Therefore, the reported hardness value here is the intrinsic value that depend on its microstructure properties.

Cetane Number Booster Additive For Diesel Fuel Synthesized From Coconut Oil, Mohammad Nasikin, Rita Arbianti, Abdul Azis

Makara Journal of Technology

To reduce NOx, SOx, HC, and particulates that produce because of using diesel fuel, can be done by increasing cetane number. One of methods is adding an additive to diesel fuel. 2-Ethyl Hexyl Nitrate (2-EHN) is a commercial additive that an organic nitrate. Making an additive in this research is used palm oil by nitration reaction that used HNO3 and H2SO4. Result of this reaction is methyl ester nitrate that has a structure looks like 2-EHN. IR spectra from research show that methyl ester nitrate is indicated by spectrum NO2 at 1635 cm-1. This result show that methyl ester nitrate …

Biodiesel's Characteristics Preparation From Palm Oil, Tilani Hamid. S, Rachman Yusuf

Makara Journal of Technology

Biodiesel’s characteristics preparation from palm oil. Using vegetable oils directly as an alternative diesel fuel has presented engine problems. The problems have been attributed to high viscosity of vegetable oil that causes the poor atomization of fuel in the injector system and pruduces uncomplete combustion. Therefore, it is necessary to convert the vegetable oil into ester (metil ester) by tranesterification process to decrease its viscosity. In this research has made biodiesel by reaction of palm oil and methanol using lye (NaOH) as catalyst with operation conditions: constant temperature at 60 oC in atmosferic pressure, palm oil : methanol volume ratio …

Analogy Method Development For Cost Estimation Of Software Design, Riyanarto Sarno, Joko Lianto Buliali, Siti Maimunah

Makara Journal of Technology

The important aspect of planning and managing software development project is to estimate the cost of a project. There are several methods for estimating the cost of a software development project, and the Analogy method is a method which gives relatively better estimates. This paper shows that the modified Analogy method selects a closer project reference, estimates more accurate project effort and cost. This study enhances the cost estimate technique by including valid and complete cost parameters, therefore the estimate of a project cost is better than the result of the standard Analogy method.

The Role Of Si3n4 Amorphous Phase In Nc-Tin/A-Si3n4 Nanocomposites In Increases The Hardness And Thermal Stability, Keba Moto

Makara Journal of Technology

The role of Si3N4 amorphous phase in nc-TiN/a-Si3N4 nanocomposites will be shown and compared with polycrystalline ZrN/Ni which has no such amorphous phase (non-composites). The presence of amorphous phase Si3N4 increases the hardness of film as well as the toughness of the bulk nanocomposites under indentation load. It has been observed that nc-TiN/a-Si3N4 nanocomposites films has higher thermal stability than ZrN/Ni polycrystalline films.

Thermodynamic Behavior Of Poly(Cyclohexylethylene) In Polyolefin Diblock Copolymers, Eric W. Cochran, Frank S. Bates

Eric W. Cochran

We report the temperature dependence of the Flory-Huggins interaction parameter for three symmetric diblock copolymer systems containing poly(cyclohexylethylene) (PCHE): poly(cyclohexylethylene-b-ethylene) (CE), poly(cyclohexylethylene-b-ethylethylene) (CEE), and poly(cyclohexylethylene-b-ethylenepropylene) (CP). Order-disorder transition temperatures (TODT) were determined using dynamic mechanical spectroscopy and interpreted with mean-field theory, (χN)ODT = 10.5, leading to well-defined expressions for χ(T). These results have been analyzed in the context of solubility parameter (δ) theory resulting in a unique parameter δC that describes the interactions in CE, CP, and CEE, where δC < δEE < δP < δE with (δE - δC) ≈ 1.6 MPa1/2 at 500 K. In contrast to the predictions of group contribution theory, this indicates that δC is in surprisingly close proximity to the solubility parameter for poly(dimethylsiloxane).

Design And Analysis For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Xiaolong Wu

UNLV Theses, Dissertations, Professional Papers, and Capstones

Fundamental issues related to the selection of a metallic fuel casting furnace design are presented and discussed including heating mechanisms, casting issues, crucible design, and issues related to the mass transport of americium. The process of evaluating all of these different criteria is undertaken to select a concept that would have the greatest chance of success for casting americium in a metallic fuel rod. Based on this evaluation process, a concept for the casting of metallic fuel pins containing high vapor pressure materials is selected and discussed. The important physics of this concept include mass transport of americium from the …

Modeling And Simulation Of The Chemical Etching Process In Niobium Cavities, Qin Xue

UNLV Theses, Dissertations, Professional Papers, and Capstones

Niobium Cavities are important parts of the integrated NC/SC high-power linear accelerator (linac) that can accelerate over 100 mA of protons to several GeV. Surface finish of the niobium cavity plays an important role of achieving the best performance of niobium cavity. The chemical etching techniques have been widely used.

Chemical etching of the inner surface of the cavity is achieved by circulating acid through it. The acid interacts with the surface and eliminates imperfections. During the etching process, a pipe with baffles is inserted within the cavity to direct the flow along the surfaces.

A 2-D, axisymmetric, steady state, …

Remote Magneto-Elastic Analyte, Viscosity And Temperature Sensing Apparatus And Associated Methods Of Sensing, Craig A. Grimes, Plamen G. Stoyanov

Chemical and Materials Engineering Faculty Patents

An analyte, viscosity, or temperature sensing apparatus for operative arrangement within a time-varying magnetic field, including a sensor with an outer surface that is chemically, frictionally, or thermally responsive and adhered to a base magnetostrictive element, and a receiver to measure a first and second value for magneto-elastic emission intensity of the sensor taken at, respectively, a first and second interrogation frequency. A change in mass or a change in material stiffness of the sensor due to the responsiveness, the viscosity and mass density of a fluid therearound, or the temperature, can be identified. The receiver, alternatively, measures a plurality …