Chemical Engineering Commons^™

Thermo-Elasto-Plastic Stability Of Biaxially Loaded Hollow Rectangular Section Steel Beam-Columns With Applied Torsion, George Adomako Kumi

Civil & Environmental Engineering Theses & Dissertations

Presented herein is an experimental and theoretical study of biaxially loaded hollow rectangular section steel beam-columns with applied torsion at elevated temperatures. The theoretical analysis is based on a system of simultaneous materially nonlinear differential equations of equilibrium for which an iterative semi-analytic solution approach is formulated. Although the primary goal of this research is to study the influence of elevated temperatures on the steel member with the complex loading, rigorous analysis is also conducted of the member at ambient temperature for comparison. The experimental part of the study involves conducting tests on the members at both ambient and high …

Quasi-Static And Impact Load Response Of Bfrp-Reinforced Concrete Beams And Post-Terrorist-Attack Sub-Assemblages, José Luis Carrasquillo

Civil & Environmental Engineering Theses & Dissertations

This dissertation presents the outcome of a theoretical and experimental study of Basalt Fiber Reinforced Polymer (BFRP) reinforced concrete beams and post-terrorist-attack subassemblages subjected to either quasi-static or impact load. Both BFRP reinforcement as well as BFRP fabric are used in this investigation. The sub-assemblage consists of an otherwise two-span beam converted to a fixed-end single-span one owing to the loss of a middle column blasted off during the terrorist attack. The simply supported beams are subjected to a midspan quasistatic or an impact load. However, each sub-assemblage is subjected to a quasi-static load up to collapse to simulate the …

Fabrication Of Nb3Sn By Magnetron Sputtering For Superconducting Radiofrequency Application, Md Nizam Sayeed

Electrical & Computer Engineering Theses & Dissertations

Particle accelerators are considered as an important device that has wide applications in cancer treatment, sterilizing waste, preserving foods, ion implantation in semiconductor industry, and in production of isotopes for medical applications. Superconducting radiofrequency (SRF) cavities are the building blocks of a linear particle accelerator. Current particle accelerators use niobium (Nb) superconductors as the sheet material to fabricate a single SRF cavity for particle acceleration. With better superconducting properties (critical temperature T_c ~ 18.3 K, superheating field H_sh~ 400 mT), Nb₃Sn is considered a potential candidate in SRF technology. Magnetron sputtering is a promising deposition …

4,6-O-Phenylethylidene Acetal Protected D-Glucosamine Carbamate-Based Gelators And Their Applications For Multi-Component Gels, Pooja Sharma, Guijun Wang

Chemistry & Biochemistry Faculty Publications

The self-assembly of carbohydrate-based low molecular weight gelators has led to useful advanced soft materials. The interactions of the gelators with various cations and anions are important in creating novel molecular architectures and expanding the scope of the small molecular gelators. In this study, a series of thirteen new C-2 carbamates of the 4,6-O-phenylethylidene acetalprotected D-glucosamine derivatives has been synthesized and characterized. These compounds are rationally designed from a common sugar template. All carbamates synthesized were found to be efficient gelators and three compounds are also hydrogelators. The resulting gels were characterized using optical microscopy, atomic force microscopy, …

Broadband Dielectric Spectroscopic Detection Of Ethanol: A Side-By-Side Comparison Of Zno And Hkust-1 Mofs As Sensing Media, Papa K. Amoah, Zeinab Mohammed Hassan, Pengtao Lin, Engelbert Redel, Helmut Baumgart, Yaw S. Obeng

Electrical & Computer Engineering Faculty Publications

The most common gas sensors are based on chemically induced changes in electrical resistivity and necessarily involve making imperfect electrical contacts to the sensing materials, which introduce errors into the measurements. We leverage thermal- and chemical-induced changes in microwave propagation characteristics (i.e., S-parameters) to compare ZnO and surface-anchored metal-organic-framework (HKUST-1 MOF) thin films as sensing materials for detecting ethanol vapor, a typical volatile organic compound (VOC), at low temperatures. We show that the microwave propagation technique can detect ethanol at relatively low temperatures (<100 >°C), and afford new mechanistic insights that are inaccessible with the traditional dc-resistance-based measurements. In addition, …

Reducing Print Time While Minimizing Loss In Mechanical Properties In Consumer Fdm Parts, Long Le, Mitchel A. Rabsatt, Hamid Eisazadeh, Mona Torabizadeh

Mechanical & Aerospace Engineering Faculty Publications

Fused deposition modeling (FDM), one of various additive manufacturing (AM) technologies, offers a useful and accessible tool for prototyping and manufacturing small volume functional parts. Polylactic acid (PLA) is among the commonly used materials for this process. This study explores the mechanical properties and print time of additively manufactured PLA with consideration to various process parameters. The objective of this study is to optimize the process parameters for the fastest print time possible while minimizing the loss in ultimate strength. Design of experiments (DOE) was employed using a split-plot design with five factors. Analysis of variance (ANOVA) was employed to …

Failure Modes For I-Section Gfrp Beams, Mamadou Konate, Zia Razzaq

Civil & Environmental Engineering Faculty Publications

This paper presents calculations for the failure modes for I-section Glass Fiber Reinforced Polymer (GFRP) beams with single mid-span web brace. Theoretical predictions are made using ASCE-LFRD Pre-Standard for FRP structures. For the member length considered, it is found that for small and medium I-sections the failure mode is governed by lateral-torsional buckling and for bigger I-sections the failure mode is governed by material rupture. The outcome of the predicted lateral-torsional buckling mode is compared with that observed experimentally.

Improving The Efficiency Of P3ht:Icba Organic Solar Cells By Modifying The Photoactive Solution Preparation Step, Matthew Blaine Samson

Electrical & Computer Engineering Theses & Dissertations

Organic solar cells (OSCs) are a promising alternative to conventional silicon solar cells. These organic devices offer the promise of facile low cost large scale solution based processing on lightweight, flexible, plastic substrates. At the present state of the technology, however, OSCs exhibit relatively low power conversion efficiencies. To improve these efficiencies, new materials are constantly being developed.

One such material is the fullerene indene-C₆₀ bisadduct (ICBA). When implemented in a poly(3-hexylthiophene-2, 5-diyl) (P3HT) : ICBA bulk heterojunction solar cell, these devices exhibit open circuit voltages exceeding 0.8 V, a value much higher than the devices made implementing phenyl-C …

Flexural Rigidity Characterization Of Retrofitted Frp Plates, Steven J. Makonis Jr., Stella B. Bondi, Zia Razzaq

Civil & Environmental Engineering Faculty Publications

Presented herein is a procedure and numerical results for flexural rigidity characterization of Fiber Reinforced Polymer (FRP) plates retrofitted with various types of fabrics. The FRP plates were retrofitted with Kevlar® 49 (Aramid), Carbon Fiber (Harness-Satin H5), and Unidirectional Carbon Fiber (T700 Aerospace Grade) fabrics, respectively. The FRP plate flexural rigidity values were calculated with a central finitedifference iterative scheme while utilizing the experimental load-deflection relations based on bending tests. The tests were performed on each plate by applying a concentrated load at the center. A fourth-order partial differential equation of plate equilibrium was adopted to estimate the plate flexural …

Preparation And Surface Studies Of Negative Electron Affinity Semiconductors Photocathodes, Khaled A. Elamrawi

Electrical & Computer Engineering Theses & Dissertations

Fabrication of high quantum efficiency, long lifetime negative electron affinity photocathodes is important for applications such as photomultipliers, image intensifiers, electron beam lithography, electron microscopy, and polarized electron sources. The surface cleanliness of the III-V semiconductor photocathode is crucial in obtaining high photosensitivity.

GaAs(100) and InP(100) photocathodes are prepared by atomic hydrogen cleaning. The cleaning effect on the photocathode performance is discussed. The surface degradation mechanisms which reduce the photocathode lifetime are presented. The photocathode surface cleanliness, structure, and morphology are studied using reflection high-energy electron diffraction (RHEED).

Quantum efficiencies of ∼14% and 8% are obtained for GaAs and InP, …

The Effects Of Electron Radiation On The Glass Transition Temperature Of A Polyetherimide, Kristen Tulloch Kern

Physics Theses & Dissertations

The effects of electron radiation on a polyetherimide (PEI), Ultem*, were investigated. In particular, the changes in the glass transition temperature (T_g) with absorbed radiation dose were studied. The polymer was exposed to mono-energetic beams of 100-keV electrons and 1.0-MeV electrons for doses up to 100 megagray (MGy). Dosimetry for the exposures was based on Monte-Carlo simulations of the transfer of energy from an energetic electron to the polymer and on comparison to Nylon standards. Dynamic mechanical analysis was used to determine the (T_g) for non-exposed PEI and the changes in (T_g) resulting from …

Thermal Characterization Of Carbon Monoxide Oxidation Catalysts Using Thermogravimetric Analysts And Differential Scanning Calorimetry, Rene A. Bartgis

Chemistry & Biochemistry Theses & Dissertations

Catalysts composed of platinum and/or palladium on tin (IV) oxide supports, with and without silica gel, as well as catalysts composed of gold on manganese oxide, have been developed for the recombination of carbon monoxide and oxygen to form carbon dioxide for use in carbon dioxide lasers. A thermogravimetric method and a differential scanning calorimetric method have been developed for the thermal characterization of these catalysts. The mass loss data and the enthalpy changes determined as the catalysts lost water were then related to existing activity data for these catalysts. No relationship was found between the thermal data and the …